Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0111  Intake Air Temperature Sensor 1 Circuit Range / Performance  


DESCRIPTION

A371036E02
1.802,2.26 2.219,1.844 false 0.104,0.083 0.583,0.281 0.479,0.198 10 false Fig. 1 0.135,0.396 1.198,0.594 1.063,0.198 10 false Resistance 2.042,1.656 2.844,1.854 0.802,0.198 10 false Acceptable 0.469,0.802 0.74,0.99 0.271,0.188 10 false 30 0.469,1.01 0.74,1.198 0.271,0.188 10 false 20 0.469,1.313 0.74,1.5 0.271,0.188 10 false 10 0.469,3.479 0.74,3.667 0.271,0.188 10 false 0.1 0.469,3.156 0.74,3.344 0.271,0.188 10 false 0.2 0.458,2.833 0.729,3.021 0.271,0.188 10 false 0.3 0.458,2.646 0.729,2.833 0.271,0.188 10 false 0.5 0.542,2.385 0.719,2.573 0.177,0.188 10 false 1 0.542,2.063 0.719,2.25 0.177,0.188 10 false 2 0.542,1.875 0.719,2.063 0.177,0.188 10 false 3 0.552,1.646 0.729,1.833 0.177,0.188 10 false 5 0.813,3.865 1.083,4.052 0.271,0.188 10 false -20 1.208,3.865 1.479,4.052 0.271,0.188 10 false 0 1.531,3.865 1.802,4.052 0.271,0.188 10 false 20 1.854,3.865 2.125,4.052 0.271,0.188 10 false 40 2.167,3.865 2.438,4.052 0.271,0.188 10 false 60 2.542,3.865 2.813,4.052 0.271,0.188 10 false 80 2.865,3.865 3.135,4.052 0.271,0.188 10 false 100 0.802,4.021 1.104,4.208 0.302,0.188 10 false (-4) 1.125,4.021 1.427,4.208 0.302,0.188 10 false (32) 1.479,4.021 1.781,4.208 0.302,0.188 10 false (68) 1.771,4.021 2.135,4.219 0.365,0.198 10 false (104) 2.104,4.021 2.469,4.219 0.365,0.198 10 false (140) 2.458,4.021 2.823,4.219 0.365,0.198 10 false (176) 2.833,4.031 3.198,4.229 0.365,0.198 10 false (212) 1.365,4.25 2.688,4.458 1.323,0.208 10 false Temperature °C (°F) 0.073,0.729 0.417,0.948 0.344,0.219 10 false (kΩ)

The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.


DTC No. DTC Detection Condition Trouble Area
P0111 When either condition below is met:
(2 trip detection logic)
1.

The intake air temperature change from the previous trip warm-up to the following trip is small.

2.

The change in the intake air temperature after engine start is less than the threshold value.


Mass air flow meter

MONITOR DESCRIPTION

The ECM performs OBD II monitoring based on the values from the intake air temperature sensor. If there is no change of the sensor value within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects the stuck intake air temperature sensor value by performing monitoring after the ignition switch is turned off or the engine is started (short soak or long soak).

MONITOR STRATEGY

Related DTCs P0111: Intake air temperature sensor rationality (After engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start)
Required Sensors/Components (Main) Intake Air Temperature (IAT) sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle
Duration 10 seconds or more
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs are not present P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P2610 (Soak timer)

After Engine Stop
Time after engine start 10 seconds or more
Battery voltage 10.5 V or more
ECT change since engine stop -40°C (-40°F) or more
ECT before engine stop 70°C (158°F) or more
Accumulated MAF amount before engine stop 6754 g or more
Key-off duration 30 minutes

After Cold Engine Start
Key-off duration 5 hours
Time after engine start 10 seconds or more
ECT 70°C (158°F) or more
Accumulated MAF amount 6754 g or more
Either of the following conditions 1 or 2 is met: -
1. Duration while engine load is low 120 seconds or more
2. Duration while engine load is high 10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

After Engine Stop
IAT change Less than 1°C (2°F)

After Cold Engine Start
IAT change Less than 1°C (2°F)

CONFIRMATION DRIVING PATTERN

A198822E01
2.179,2.853 2.807,3.183 0.628,0.330 10 Warming Up 2.891,2.857 4.061,3.046 1.169,0.190 10 5 minutes or more 2.025,2.091 2.222,2.279 0.198,0.188 10 [A] 2.522,1.785 2.747,1.974 0.225,0.189 10 [B] 3.356,1.762 3.567,1.949 0.211,0.187 10 [C] 4,3.109 4.239,3.279 0.238,0.171 10 [D] 0.498,1.077 1.615,1.251 1.118,0.173 10 40 km/h (25 mph) 1.299,1.91 1.672,2.082 0.373,0.172 10 Idling 0.498,2.212 1.674,2.361 1.177,0.149 10 Ignition Switch ON 4.166,0.182 5.806,0.333 1.640,0.151 10 Total of 5 minutes or more 4.799,0.699 5.002,0.884 0.203,0.185 10 [E] 6.158,3.389 6.359,3.562 0.201,0.173 10 [F]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

HINT:

During steps [A] through [C], if the change in the intake air temperature is below 1°C (33.8°F), the intake air temperature sensor (MAF meter) is malfunctioning. It is not necessary to continue this procedure.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0111.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].



13.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result again [F].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F] again.


15.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0111 and other DTCs are output A
P0111 is output B

HINT:
·

If any DTCs other than P0111 are output, troubleshoot those DTCs first.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





A

B