Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P144C  Open in Secondary Air Injection System Heater Control Circuit  P144D  Short in Secondary Air Injection System Heater Control Circuit  


DESCRIPTION

The ECM operates the air pump heater (AI-HTR) relay which causes the air pump heater (AI-HTR) to operate.

DTC No. DTC Detection Condition Trouble Area
P144C Open or short in the air pump heater (AI-HTR) relay circuit for 5 seconds (1 trip detection logic).
·

Open or short in air pump heater (AI-HTR) relay circuit

·

Air pump heater (AI-HTR) relay

·

ECM


P144D Open or short in the air pump heater (AI-HTR) relay circuit for 5 seconds (1 trip detection logic).
·

Open or short in air pump heater (AI-HTR) relay circuit

·

Air pump heater (AI-HTR) relay

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air pump heater (AI-HTR) relay circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater (AI-HTR) relay is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater (AI-HTR) relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.

·

The battery voltage is not applied to terminal HAI1 while the air pump heater (AI-HTR) relay is off.

·

The battery voltage is applied to terminal HAI1 while the air pump heater (AI-HTR) relay is on.


MONITOR STRATEGY

Related DTCs P144C: Air pump heater relay circuit range check (Low voltage)
P144D: Air pump heater relay circuit range check (High voltage)
Required Sensors/Components (Main) Air pump heater relay (AI-HTR)
Required Sensors/Components (Related) -
Frequency of operation Continuous
Duration 5 seconds
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Case 1
Monitor runs whenever following DTCs not stored None
Current air pump heater relay (AI-HTR) ON
Last air pump heater (AI-HTR) relay ON
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

Case 2
Monitor runs whenever following DTCs not stored None
Current air pump heater (AI-HTR) relay OFF
Last air pump heater (AI-HTR) relay OFF
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

P144C
Air pump heater (AI-HTR) relay output terminal voltage Low

P144D
Air pump heater (AI-HTR) relay output terminal voltage High

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait for 10 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.

8.

Activate the air pump heater for 10 seconds or more.

HINT:
·

The active test activates the air pump heater for up to 60 seconds.

·

To protect the air pump heater, do not perform this test more than 4 times in a row.



9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P144C or P144D.

13.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



14.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR PUMP HEATER (AI-HTR) RELAY
A232574E01
3.198,1.523 3.303,1.666 0.105,0.143 10 3 2.815,1.606 3.17,1.606 false 3.198,1.049 3.303,1.192 0.105,0.143 10 5 2.815,1.132 3.17,1.132 false 1.926,0.319 2.031,0.462 0.105,0.143 10 1 2.325,0.702 2.04,0.403 false 3.198,0.319 3.303,0.462 0.105,0.143 10 2 2.921,0.714 3.176,0.403 false

a.

Remove the air pump heater (AI-HTR) relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

2.CHECK AIR PUMP HEATER (AI-HTR) RELAY (POWER SOURCE)

NG

REPLACE AIR PUMP HEATER (AI-HTR) RELAY

2.CHECK AIR PUMP HEATER (AI-HTR) RELAY (POWER SOURCE)
a.
A258729E08
0.12,0.03 0.373,0.213 0.253,0.184 10 *1 1.586,1.432 2.194,1.657 0.607,0.225 10 *2

Remove the air pump heater (AI-HTR) relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (Air pump heater (AI-HTR) relay) - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Air Pump Heater (AI-HTR) Relay



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER (AI-HTR) RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER (AI-HTR) RELAY)
a.

Remove the air pump heater (AI-HTR) relay from the engine room relay block.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (Air pump heater (AI-HTR) relay) - D74-60 (HAI1) Always Below 1 Ω
2 (Air pump heater (AI-HTR) relay) or D74-60 (HAI1) - Body ground Always 10 kΩ or higher




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR