The battery supplies electricity to the ECM even when the ignition switch is in the OFF position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and sets the DTC.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0560 | Open in ECM back up power source circuit
(1 trip detection logic) |
·
Open in back up power source circuit ·
Battery ·
Battery terminals ·
EFI NO. 1 fuse ·
ECM |
If DTC P0560 is set, the ECM does not store other DTCs or the data stored in the ECM is partly erased.
| Related DTCs | P0560: ECM system voltage |
| Required Sensors/Components (Main) | ECM |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 3 seconds |
| MIL Operation | Immediate (MIL illuminated after next engine start) |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Stand-by RAM | Initialized |
| ECM power source | Less than 3.5 V |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Wait 5 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0560.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Remove the EFI NO. 1 fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI NO. 1 fuse | Always | Below 1 Ω |
OK
NG
Check the harness and the connector between the EFI NO. 1 fuse and ECM.
Remove the EFI NO. 1 fuse from the engine room relay block.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI NO. 1 fuse terminal 2 - A24-1 (BATT) | Always | Below 1 Ω |
| EFI NO. 1 fuse terminal 2 or A24-1 (BATT) - Body ground | Always | 10 kΩ or higher |
Check the harness and the connector between the EFI NO. 1 fuse and battery.
Remove the EFI NO. 1 fuse from the engine room relay block.
Disconnect the positive battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Battery positive (+) terminal - EFI NO. 1 fuse terminal 1 | Always | Below 1 Ω |
| Battery positive (+) terminal or EFI NO. 1 fuse terminal 1- Body ground | Always | 10 kΩ or higher |
OK
NG
Check that the battery is not depleted (See page Engine / Hybrid System>3UR-FE CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION).
Battery is not depleted.
OK
NG
Check that the battery terminals are not loose or corroded.
Battery terminals are not loose or corroded.
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and turn the Techstream off.
Start the engine and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P0560 is output | A |
| No DTC is output | B |
A
B