Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit Malfunction  P0552  Power Steering Pressure Sensor Circuit Low Input  P0553  Power Steering Pressure Sensor Circuit High Input  


DESCRIPTION

The power steering oil pressure sensor is turned ON when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.

DTC Code DTC Detection Condition Trouble Area
P0550 Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0552 Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0553 Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM



MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and sets a DTC.

MONITOR STRATEGY

Related DTCs P0550: Power steering pressure sensor range check (Chattering)
P0552: Power steering pressure sensor range check (Low Resistance)
P0553: Power steering pressure sensor range check (High Resistance)
Required Sensors/Components Power steering pressure sensor
Frequency of operation Continuous
Duration 0.5 seconds
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Time after starter signal ON to OFF 2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

P0550:
Power steering pressure sensor voltage Less than 0.28 V, or more than 4.9 V

P0552:
Power steering pressure sensor voltage Less than 0.28 V

P0553:
Power steering pressure sensor voltage More than 4.9 V

CONFIRMATION DRIVING PATTERN

A198821E01
0.763,1.195 1.197,1.414 0.434,0.218 10 Idling 0.092,1.579 1.354,1.777 1.262,0.198 10 Ignition Switch ON 1.768,1.45 1.994,1.609 0.226,0.159 10 [A] 3.29,1.076 3.483,1.269 0.193,0.193 10 [B] 4.803,2.921 5.033,3.151 0.230,0.230 10 [C] 3.043,2.253 3.735,2.437 0.693,0.184 10 5 seconds

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds [B].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0550, P0552 or P0553.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A162851E02
5.041,0.56 5.354,0.725 0.313,0.165 10 PSP 5.527,2.965 5.812,3.130 0.286,0.165 10 D74 5.036,1.466 5.442,1.631 0.406,0.165 10 VCV1 1.903,0.56 2.216,0.725 0.313,0.165 10 PSP 1.985,1.47 2.215,1.635 0.230,0.165 10 VC 5.041,2.381 5.502,2.537 0.461,0.156 10 ETHW 5.527,3.129 5.886,3.303 0.360,0.174 10 ECM 4.783,0.471 4.967,0.627 0.184,0.156 10 72 4.783,1.367 4.967,1.523 0.184,0.156 10 67 4.783,2.292 4.967,2.448 0.184,0.156 10 97 2.318,0.462 2.446,0.618 0.128,0.156 10 2 2.304,1.382 2.414,1.543 0.110,0.161 10 1 2.304,2.288 2.423,2.444 0.119,0.156 10 3 2.002,2.389 2.206,2.537 0.205,0.149 10 E2 0.503,2.949 0.791,3.112 0.288,0.163 10 D46 0.503,3.11 2.798,3.280 2.295,0.170 10 Power Steering Oil Pressure Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the D74 ECM connector.


b.

Disconnect the D46 power steering oil pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D46-2 (PSP) - D74-72 (PSP) Always Below 1 Ω
D46-1 (VC) - D74-67 (VCV1) Always Below 1 Ω
D46-3 (E2) - D74-97 (ETHW) Always Below 1 Ω
D46-2 (PSP) or D74-72 (PSP) - Body ground Always 10 kΩ or higher
D46-1 (VC) or D74-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

2.REPLACE POWER STEERING OIL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER STEERING OIL PRESSURE SENSOR
a.

Replace the power steering oil pressure sensor.



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0550, P0552 and/or P0553 are output A
No DTC is output B



A

B

END