Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC Code Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P2610 Soak timer (built into ECM) ECM internal malfunction ECM Engine running 2 trip

DESCRIPTION

To ensure the accuracy of the EVAP (Evaporative Emission) monitor values, the soak timer, which is built into the ECM, measures 5 hours (+/-15 minutes) from when the ignition switch is turned off, before the monitor is run. This allows the fuel to cool down, which stabilizes the EVAP pressure. When 5 hours have elapsed, the ECM turns on.

A164737E01
5.59,4.332 5.936,4.488 0.346,0.156 10 ECM 4.992,1.18 5.731,1.497 0.739,0.317 10 Soak Timer IC 5.029,2.544 5.671,2.875 0.642,0.332 10 Power Source IC 5.002,3.347 5.732,3.669 0.730,0.323 10 Main Relay Control IC 4.324,0.9 4.724,1.055 0.400,0.156 10 IGSW 4.523,2.697 4.739,2.848 0.216,0.151 10 +B 4.303,3.492 4.736,3.649 0.434,0.157 10 MREL 3.175,3.893 3.433,4.049 0.258,0.156 10 EFI 1.895,3.314 2.542,3.470 0.647,0.156 10 EFI NO. 1 0.55,3.875 1.021,4.058 0.471,0.184 10 Battery 1.419,2.343 2.066,2.508 0.647,0.165 10 IG2 MAIN 0.373,2.33 0.705,2.485 0.332,0.156 10 AM2 3.908,1.105 4.194,1.270 0.286,0.165 10 IGN 2.837,1.698 3.095,1.864 0.258,0.165 10 IG2 1.428,1.67 2.371,1.845 0.943,0.174 10 Ignition Switch 0.07,0.051 2.482,0.346 2.413,0.295 12 Reference (System Diagram):

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle
Duration 2 times: Case 1
-: Case 2 and 3
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs are not stored None

Case 1
All of the following conditions are met -
Battery voltage 8 V or more
Ignition switch OFF
CPU clock elapsed time 1.96608 seconds or more

Case 2
All of the following conditions are met -
Internal engine off timer (elapsed time from engine stop) 10 minutes or more, and less than 30 minutes
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

Case 3
All of the following conditions are met -
Internal engine off timer (elapsed time from engine stop) 10 minutes or more, and less than 30 minutes
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Case 1
One of the following conditions is met Condition A, B or C
A. Both of the following conditions are met Condition (a) and (b)
(a) CPU clock elapsed time 1.96608 seconds or more, and less than 8.323072 seconds
(b) Internal Engine off timer 9.375 seconds or more
B. Both of the following conditions are met Condition (c) and (d)
(c) CPU clock elapsed time 8.323072 to 10.420224 seconds
(d) Internal Engine off timer 18.75 seconds or more
C. Both of the following conditions are met Condition (e) and (f)
(e) CPU clock elapsed time More than 10.420224 seconds
(f) Internal Engine off timer Less than 9.375 seconds

Case 2
ECM had the started record Yes

Case 3
ECM had the started record No

CONFIRMATION DRIVING PATTERN

A199319E01
0.226,1.73 1.419,1.914 1.193,0.184 10 Ignition Switch ON 0.264,2.211 1.457,2.395 1.193,0.184 10 Ignition Switch off 2.744,1.851 2.955,2.098 0.211,0.246 10 [A] 6.166,2.901 6.369,3.103 0.202,0.202 10 [B] 4.21,2.561 5.644,2.745 1.434,0.184 10 10 minutes or more 1.006,1.209 1.447,1.428 0.441,0.218 10 Idling

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 10 minutes or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2610.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


13.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Start the engine and wait for 10 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

If no pending DTC is displayed, the repair has been successfully completed.



NEXT

END