Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

·

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the exhaust valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E02
4.651,0.815 6.372,1.026 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.651,1.325 5.477,1.485 0.825,0.161 10 CKP Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.758,3.922 2.160,0.174 10 Camshaft Oil Control Valve (OCV) 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.651,1.827 5.490,1.981 0.839,0.154 10 MAF Meter 4.651,2.854 5.449,3.042 0.797,0.188 10 ECT Sensor 4.651,2.344 5.018,2.511 0.367,0.167 10 TPS 4.651,3.353 5.004,3.506 0.353,0.154 10 VSS 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 5.049,5.101 1.166,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC Code DTC Detection Condition Trouble Area
P0013 An open or short in the Camshaft Oil Control Valve (OCV) for exhaust side (for Bank 1) circuit (1 trip detection logic).
·

Open or short in Camshaft Oil Control Valve (OCV) (for exhaust side of Bank 1) circuit

·

OCV for exhaust camshaft (for Bank 1)

·

ECM


P0023 An open or short in the OCV for exhaust side (for Bank 2) circuit (1 trip detection logic).
·

Open or short in OCV (for exhaust side of Bank 2) circuit

·

OCV for exhaust camshaft (for Bank 2)

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY

Related DTCs P0013: Exhaust camshaft OCV (for Bank 1)
P0023: Exhaust camshaft OCV (for Bank 2)
Required Sensors/Components (Main) Exhaust camshaft OCV
Required Sensors/Components (Related) -
Frequency of operation Continuous
Duration 1 second
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present None
All of following conditions met -
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 0.5 seconds or more

Case 1
One of following conditions met -
A. All of the following conditions are met -
Battery voltage 11 to 13 V
Target duty cycle Less than 70%
B. All of following conditions met -
Battery voltage 13 V or more
Target duty cycle Less than 80%

Case 2
Current cut status Not cut

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Output duty cycle 100% or more

Case 2
Output duty cycle 3% or less

COMPONENT OPERATING RANGE

OCV duty cycle 3 to 100%

CONFIRMATION DRIVING PATTERN

A198818E01
0.071,1.648 1.257,1.825 1.186,0.177 10 Ignition Switch ON 3.178,1.526 3.389,1.709 0.211,0.184 10 [A] 4.817,2.976 5.032,3.149 0.215,0.173 10 [B] 3.045,2.338 3.722,2.480 0.677,0.142 10 5 seconds

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds [A].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0013 or P0023.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A162759E02
5.868,4.237 6.218,4.421 0.350,0.184 10 ECM 5.42,0.506 5.854,0.662 0.434,0.156 10 OE1+ 5.42,1.234 5.854,1.390 0.434,0.156 10 OE1- 5.42,2.481 5.854,2.637 0.434,0.156 10 OE2+ 5.42,3.21 5.854,3.366 0.434,0.156 10 OE2- 0.103,1.631 2.602,1.843 2.499,0.211 10 OCV for Exhaust Camshaft (for Bank 1) 0.103,3.617 2.593,3.828 2.490,0.211 10 OCV for Exhaust Camshaft (for Bank 2) 0.101,1.449 0.387,1.614 0.286,0.165 10 D44 0.101,3.448 0.387,3.613 0.286,0.165 10 D45 1.466,0.491 1.592,0.681 0.126,0.191 10 1 1.473,1.229 1.592,1.402 0.119,0.173 10 2 1.466,2.444 1.592,2.635 0.126,0.191 10 1 1.473,3.182 1.592,3.356 0.119,0.173 10 2 5.868,4.085 6.153,4.239 0.286,0.154 10 D74 5.17,3.194 5.344,3.350 0.174,0.156 10 49 5.17,2.456 5.344,2.612 0.174,0.156 10 50 5.17,1.223 5.344,1.379 0.174,0.156 10 55 5.17,0.485 5.344,0.641 0.174,0.156 10 56

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0023 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).



PROCEDURE

1.CHECK DTC (DTC P0013 OR P0023)
a.

Connect the Techstream to the DLC3.


b.

Clear DTC after recording the freeze frame data and DTC.


c.

Turn the ignition switch off.


d.

Allow the engine to idle and check DTC.


e.

Check that P0013 or P0023 is not present.

OK:

P0013 or P0023 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft oil control valve assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
a.

Disconnect the D44 or D45 OCV connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D44-1 - D74-56 (OE1+) Always Below 1 Ω
D44-2 - D74-55 (OE1-) Always Below 1 Ω
D45-1 - D74-50 (OE2+) Always Below 1 Ω
D45-2 - D74-49 (OE2-) Always Below 1 Ω
D44-1 or D74-56 (OE1+) - Body ground Always 10 kΩ or higher
D44-2 or D74-55 (OE1-) - Body ground Always 10 kΩ or higher
D45-1 or D74-50 (OE2+) - Body ground Always 10 kΩ or higher
D45-2 or D74-49 (OE2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR