Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P060A  Internal Control Module Monitoring Processor Performance  


DESCRIPTION

The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, a DTC is output.

DTC Code DTC Detection Condition Trouble Area
P060A When either condition below is met:
·

ECM main CPU error

·

ECM sub CPU error

·

Electronic throttle monitoring CPU error


ECM

MONITOR STRATEGY

Related DTCs None
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of operation Once per driving cycle
Duration -
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None

TYPICAL MALFUNCTION THRESHOLDS

When either condition below is met: Condition 1 or 2
1. When all conditions below are met: -
- CPU reset 1 time or more
- Learned TP - Learned APP 0.4 V or more
- Electronic throttle actuator OFF
2. CPU reset 2 times or more

CONFIRMATION DRIVING PATTERN

A199238E02
0.212,1.721 1.405,1.904 1.193,0.184 10 Ignition Switch ON 0.25,2.202 1.443,2.385 1.193,0.184 10 Ignition Switch off 2.558,1.557 2.769,1.803 0.211,0.246 10 [A] 6.176,2.963 6.378,3.165 0.202,0.202 10 [B] 3.775,2.552 5.209,2.736 1.434,0.184 10 16 seconds or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 16 seconds or more [A].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P060A.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Check DTC.

OK:

P060A is not present.




OK

NG