Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

The ECM monitors its internal operation and it will set this DTC when it detects an internal malfunction.

DTC No. DTC Detection Condition Trouble Area
P062F ECM internal error (EEPROM) ECM

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and sets a DTC.

MONITOR STRATEGY

Related DTCs P062F: Internal control module EEPROM error
Required sensors/Components (Main) ECM
Required sensors/Components (Related) -
Frequency of operation Once per driving cycle
Duration 3 times
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Time after engine start 10 seconds or more
Battery voltage 8 V or higher
Ignition switch ON

TYPICAL MALFUNCTION THRESHOLDS

Permanent fault code data Mismatch (3 times or more)

CONFIRMATION DRIVING PATTERN

A199238E03
0.212,1.721 1.405,1.904 1.193,0.184 10 Ignition Switch ON 0.25,2.202 1.443,2.385 1.193,0.184 10 Ignition Switch off 2.533,1.602 2.745,1.848 0.211,0.246 10 [A] 6.176,2.963 6.378,3.165 0.202,0.202 10 [B] 3.775,2.552 5.197,2.736 1.422,0.184 10 30 seconds or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 30 seconds or more [A].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P062F.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




PROCEDURE

1.READ OUTPUT DTC (DTC P062F)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and turn the Techstream off.


f.

Disconnect the Techstream.


g.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


h.

Connect the cable to the negative (-) battery terminal.


i.

Connect the Techstream to the DLC3.


j.

Turn the ignition switch to ON.


k.

Turn the Techstream on.


l.

Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.


m.

Read DTCs.

Result
Result Proceed to
No output A
P062F B



A

B