Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › THROTTLE BODY
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233916 THROTTLE BODY A

3UR-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 22210 1.INSTALL THROTTLE BODY ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A313317E01
2.277,0.288 2.464,0.458 0.187,0.170 10 *a 1.687,1.868 1.873,2.038 0.187,0.170 10 *a 1.63,1.05 2.127,0.396 2.127,0.396 2.26,0.396 false 1.279,1.574 1.529,1.959 1.529,1.959 1.683,1.959 false 1.5,0.378 1.067,0.378 false 0.872,0.284 1.032,0.450 0.159,0.165 10 *1 0.248,0.939 0.408,1.104 0.159,0.165 10 *2 0.739,1.442 0.577,1.03 0.577,1.03 0.439,1.03 false

Install the No. 5 water by-pass hose to the throttle with motor body assembly, and slide the clamp to secure the hose.

Text in Illustration
*1 No. 5 Water By-pass Hose
*2 No. 4 Water By-pass Hose
*a White Mark

HINT:

Make sure the hose color is shown in the illustration.



b.

Install the No. 4 water by-pass hose to the throttle with motor body assembly, and slide the clamp to secure the hose.

HINT:

Make sure the hose color is shown in the illustration.



c.
A165587E04
1.708,0.729 1.979,0.208 1.979,0.208 2.198,0.208 true 2.302,1.313 2.385,0.781 2.385,0.781 2.51,0.781 true 0.375,2.646 0.583,2.844 0.208,0.198 10 false *c 2.906,2.646 3.125,2.844 0.219,0.198 10 false *d 2.25,0.115 2.521,0.313 0.271,0.198 10 false *a 2.542,0.677 2.75,0.854 0.208,0.177 10 false *b

Align the protrusion of the gasket with the groove of the intake manifold.

Text in Illustration
*a Groove
*b Protrusion
*c Intake Manifold Side
*d Throttle Body Side


d.

Install a new gasket to the intake manifold.


e.

Install the throttle with motor body with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Connect the throttle position sensor and control motor connector.


g.
A313318E02
0.573,1.5 0.938,1.281 0.938,1.281 1.042,1.281 true 0.688,0.979 0.531,0.677 0.531,0.677 0.427,0.677 true 2.021,0.781 2.573,0.24 2.573,0.24 2.656,0.24 true 2.156,1.01 1.938,1.438 1.938,1.438 1.823,1.438 true 1.052,1.198 1.219,1.354 0.167,0.156 10 false *a 0.135,0.583 0.396,0.771 0.26,0.188 10 true *1 2.667,0.146 2.833,0.302 0.167,0.156 10 false *2 1.615,1.344 1.844,1.542 0.229,0.198 10 true *b

Connect the No. 5 water by-pass hose to the water inlet housing, and slide the clamp to secure the hose.

Text in Illustration
*1 No. 5 Water By-pass Hose
*2 No. 4 Water By-pass Hose
*a Yellow Mark
*b Pink Mark

HINT:

Make sure the hose color is shown in the illustration.



h.

Connect the No. 4 water by-pass hose to the No. 3 water by-pass pipe, and slide the clamp to secure the hose.

HINT:

Make sure the hose color is shown in the illustration.



Hide 17880 3.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 11209 5.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 6.PERFORM INITIALIZATION

NOTICE:

Perform the following procedure after replacing the throttle body assembly or any throttle body assembly components. The following procedure should also be performed if the throttle body assembly is cleaned.


a.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above step again.



b.

Connect the Techstream to the DLC3 and clear the DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


c.

Perform the "Inspection After Repairs" (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


d.

Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

Standard:
Condition Engine Idle Speed
A/C switched off 650 to 750 rpm


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or neutral.




e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Pos. Sensor Output. Fully depress the accelerator pedal and check that the value is 60% or more.


f.

Perform a road test and confirm that there are no abnormalities.