Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0337  Crankshaft Position Sensor "A" Circuit Low Input  P0338  Crankshaft Position Sensor "A" Circuit High Input  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a crankshaft position sensor plate and Magnetic Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed to the rear end of the crankshaft. The crankshaft position sensor outputs 34 rotation signals per crankshaft revolution. The ECM uses the G2 signal to distinguish between the cylinders, and uses the NE signal to detect the crankshaft position and engine speed.

DTC No. DTC Detection Condition Trouble Area
P0335
·

No CKP sensor signal to ECM while cranking (1 trip detection logic)

·

No CKP sensor signal to ECM at engine speed of less than 450 rpm (1 trip detection logic)


·

Open or short in CKP sensor circuit

·

CKP sensor

·

CKP sensor plate

·

ECM


P0337 Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
·

Open or short in CKP sensor circuit

·

CKP sensor

·

CKP sensor plate

·

ECM


P0338 Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
·

Open or short in CKP sensor circuit

·

CKP sensor

·

CKP sensor plate

·

ECM


P0339 Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have elapsed since starter signal switched from ON to OFF
·

Open or short in CKP sensor circuit

·

CKP sensor

·

CKP sensor plate

·

ECM



A211721E02
2.827,1.419 3.206,1.599 0.379,0.181 10 GND 2.827,1.966 3.206,2.146 0.379,0.180 10 GND 0.246,1.872 0.477,2.035 0.231,0.163 10 G2 0.246,1.323 0.508,1.486 0.261,0.163 10 NE 1.108,2.472 2.049,2.649 0.941,0.177 10 20 msec./DIV. 2.708,0.749 3.274,0.926 0.566,0.177 10 5 V/DIV. 0.102,0.059 1.958,0.241 1.856,0.182 10 NE and G2 Signal Waveform

Reference: Inspection using an oscilloscope.

Standard:
Tester Connection Tool Setting Condition Specified Condition
D74-110 (NE+) - D74-111 (NE-) 5 V/DIV., 20 msec./DIV. Cranking or idling The correct waveform is as shown
D74-90 (G2) - D74-89 (G2-) 5 V/DIV., 20 msec./DIV. Cranking or idling The correct waveform is as shown


HINT:

G2 stands for the camshaft position sensor signal, and NE stands for the crankshaft position sensor signal.



MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Related DTCs P0335: Crankshaft position sensor range check/rationality
P0337: Crankshaft position sensor check (Low voltage)
P0338: Crankshaft position sensor check (High voltage)
Required sensors/Components (Main) Crankshaft Position (CKP) sensor
Required sensors/Components (Related) Camshaft position sensor
Frequency of operation Continuous
Duration -: Verify pulse input (case 2)
4.7 seconds: Verify pulse input (case 1)
4 seconds: Others
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not stored None

P0335 Crankshaft Position Sensor Verify Pulse Input (Case 1):
Battery voltage Higher than 6 V
CKP sensor voltage 0.3 to 4.7 V
Time after starter off to ON 0.5 seconds or more
Ignition switch ON
Starter ON
Minimum battery voltage while starter ON Below 11 V

P0335 Crankshaft Position Sensor Verify Pulse Input (Case 2):
Battery voltage Higher than 6 V
CKP sensor voltage 0.3 to 4.7 V
Ignition switch ON
Engine speed (Top dead center) 450 rpm or higher
Engine speed (30°CA) 450 rpm or higher
Starter OFF
Time after starter turned from ON to OFF 3 seconds or more

P0337, P0038 Crankshaft Position Sensor Range Check (Low voltage, High voltage):
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

P0335 Crankshaft Position Sensor Verify Pulse Input:
Crankshaft Position (CKP) sensor signal No signal

P0337 Crankshaft Position Sensor Range Check (Low voltage):
CKP sensor voltage Less than 0.3 V

P0338 Crankshaft Position Sensor Range Check (High voltage):
CKP sensor voltage More than 4.7 V

COMPONENT OPERATING RANGE

CKP sensor
·

CKP sensor output voltage fluctuates while engine crankshaft revolving

·

34 CKP sensor signals per crankshaft revolution


CKP sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0335, P0337 or P0338.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



13.

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A164993E09
1.414,2.288 1.634,2.444 0.221,0.156 10 D3 1.414,2.438 3.134,2.612 1.721,0.174 10 Crankshaft Position Sensor 2.907,1.944 3.035,2.100 0.128,0.156 10 3 2.907,1.408 3.035,1.564 0.128,0.156 10 2 2.907,0.858 3.035,1.014 0.128,0.156 10 1 5.461,0.939 5.766,1.089 0.305,0.150 10 NE+ 5.461,1.479 5.766,1.628 0.305,0.150 10 NE- 2.519,1.479 2.824,1.628 0.305,0.150 10 NE- 5.461,2.015 5.860,2.164 0.398,0.150 10 VCV2 2.593,2.015 2.824,2.164 0.232,0.150 10 VC 5.205,1.948 5.389,2.097 0.184,0.149 10 66 5.138,1.412 5.388,1.561 0.250,0.149 10 111 5.128,0.87 5.388,1.019 0.260,0.149 10 110 5.972,2.562 6.260,2.717 0.288,0.156 10 D74 5.972,2.704 6.315,2.860 0.343,0.156 10 ECM 2.527,0.939 2.824,1.095 0.297,0.156 10 NE+

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the Techstream. To check, follow the procedures below:

1.

Connect the Techstream to the DLC3.

2.

Start the engine.

3.

Turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor output voltage is insufficient.


·

Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


d.

Start the engine.


e.

Read the values displayed on the Techstream while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the Techstream.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the Techstream remains zero (0), there may be an open or short in the Crankshaft Position (CKP) sensor circuit.





OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
U151596E02
2.885,2.708 2,2.188 false 0.135,0.25 2.469,0.656 2.333,0.406 10 false Front view of wire harness connector: (to Camshaft Position Sensor) 0.469,2.073 0.74,2.271 0.271,0.198 10 false D3 2.948,2.677 3.302,2.927 0.354,0.25 10 false VC

a.

Disconnect the D3 crankshaft position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D3-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the D3 crankshaft position sensor connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D3-1 (NE+) - D74-110 (NE+) Always Below 1 Ω
D3-2 (NE-) - D74-111 (NE-) Always Below 1 Ω
D3-1 (NE+) or D74-110 (NE+) - Body ground Always 10 kΩ or higher
D3-2 (NE-) or D74-111 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E98
2.163,1.53 2.360,1.731 0.197,0.201 10 *c 0.49,1.765 0.757,1.973 0.267,0.208 10 *a 2.673,1.765 2.940,1.973 0.267,0.208 10 *b 2.833,1.978 3.414,2.144 0.581,0.165

a.

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.




OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.




OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.


NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Refer to the confirmation driving pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0335, P0337, P0338 and/or P0339 B

HINT:

If the engine does not start, replace the ECM.




A

END

B

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the D3 crankshaft position sensor connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D3-3 (VC) - D74-66 (VCV2) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR