Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM27M0U _51 Engine / Hybrid System _049105 3UR-FBE ENGINE MECHANICAL _0234016 ENGINE ASSEMBLY A

3UR-FBE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53301 7.REMOVE HOOD SUB-ASSEMBLY

a.
A302499

Using a screwdriver, release the 2 clips and remove the hood support assembly.

HINT:

Tape the screwdriver tip before use.


CAUTION:

Remove the hood support assembly while supporting the hood by hand.



b.

Remove the 4 bolts and hood.


Hide 85110 8.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Remove the windshield wiper motor (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 55701J 9.REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY

Hide 11209 10.REMOVE V-BANK COVER SUB-ASSEMBLY

a.
A380096E01
0.438,1.51 0.438,0.802 0.438,0.802 0.573,0.802 false 0.438,1.521 0.583,1.521 false 0.906,1.667 1.094,1.667 false 2.219,1.177 2.219,1.427 2.219,1.427 2.323,1.427 false 2.75,0.927 2.948,0.708 2.948,0.708 2.948,0.542 false 2.771,0.542 2.948,0.542 false 0.625,0.719 1.698,0.917 1.073,0.198 10 false Grommet 1.135,1.583 1.594,1.781 0.458,0.198 10 false Pin 2.375,1.333 2.99,1.531 0.615,0.198 10 false Hook 2.24,0.448 3.313,0.646 1.073,0.198 10 false Bracket

Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.


Hide 17880 11.REMOVE AIR CLEANER HOSE ASSEMBLY

a.
U151488

Disconnect the vacuum hose and ventilation hose.


b.

Loosen the 2 clamps.


c.

Remove the air cleaner hose.


Hide 17700 12.REMOVE AIR CLEANER ASSEMBLY

a.
A309637E06
0.052,0.042 0.938,0.438 0.885,0.396 10 true for Type A: 0.052,2.229 0.906,2.583 0.854,0.354 10 true for Type B:

Remove the air cleaner cap.

i.

Disconnect the MAF meter connector.


ii.

Using a clip remover, detach the wire harness clamp.


iii.

for Type A:

Unfasten the 4 hook clamps and then remove the air cleaner cap.


iv.

for Type B:

Unfasten the 2 hook clamps and then remove the air cleaner cap.



b.

Remove the air cleaner element.


c.
A309638E06
0.031,0.042 0.885,0.469 0.854,0.427 10 true for Type A: 0.031,2.24 0.938,2.729 0.906,0.49 10 true for Type B:

Remove the 2 bolts and air cleaner case.


Hide 16571 13.REMOVE INLET RADIATOR HOSE

Hide 16572 14.REMOVE OUTLET RADIATOR HOSE

Hide 53101 15.REMOVE RADIATOR GRILLE SUB-ASSEMBLY

Hide 53293C 16.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 53294C 17.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 23801P 21.DISCONNECT FUEL MAIN AND RETURN HOSE

a.
A308865

Remove the fuel pipe clamp.


b.

Disconnect the fuel main and return hoses (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 22.DISCONNECT WIRE HARNESS AND HOSE

a.
A163789

Disconnect the union to check valve hose.


b.

Disconnect the purge line hose.


c.
A163788

Disconnect the heater hoses.


d.

Disconnect the clamp and ECM connector.

HINT:

Refer to the following procedures to disconnect the ECM connector (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>ECM>REMOVAL).



e.
U151465

Disconnect the 4 connectors from the connector holder block.


f.
A163791

Remove the nut and connector bracket and disconnect the 2 air pump connectors.


g.

Remove the bolt and disconnect the ground wire.


h.

Disconnect the 2 air injection system hoses.


i.
A163790

Remove the nut and disconnect the wire from the positive (+) battery cable.


j.

Disconnect the cable from the positive (+) battery terminal.


k.

Remove the bolt and disconnect the ground wire.


l.

Disconnect the 4 air injection control driver connectors.


m.

Remove the nut and disconnect the wire and 2 clips from the engine room junction block.


n.

Disconnect the 2 connectors and 2 clips from the engine room junction block.


Hide 88320 23.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 44320 24.DISCONNECT VANE PUMP ASSEMBLY

Hide 17410 26.REMOVE EXHAUST PIPE ASSEMBLY

a.

Remove the exhaust pipe assembly (See page Engine / Hybrid System>3UR-FBE EXHAUST>EXHAUST PIPE>REMOVAL).


Hide 37110 27.REMOVE PROPELLER SHAFT ASSEMBLY

a.

for 2WD:

Remove the propeller shaft (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 2WD)>REMOVAL).


b.

for 4WD:

Remove the propeller shaft (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>REMOVAL).


Hide 37140 28.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

a.

Remove the front propeller shaft (See page Drivetrain>PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>REMOVAL).


Hide 53736 29.REMOVE FRONT FENDER APRON SEAL RH

Hide 53739A 30.REMOVE FRONT FENDER APRON SEAL REAR RH

Hide 11452 31.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17167 32.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 33.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 35000 36.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

Hide 32101 37.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E02
1.359,1.727 1.661,1.883 0.302,0.156 10 SST 0.829,1.22 0.829,1.812 0.829,1.812 1.312,1.812 false 1.076,1.054 1.076,1.812 false

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A163779

Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft position sensor rotor.


Hide 16268 38.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A163785

Remove the 2 bolts and disconnect the hose. Then remove the water by-pass pipe.


Hide 39.REMOVE ENGINE ASSEMBLY

a.
U151520

Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Item Part No.
Engine hanger 12281-38150
Bolt 90119-A0166



b.

Attach an engine sling device and hang the engine with a chain block.


c.
A163780E04
0.104,0.104 0.396,0.49 0.292,0.385 10 true RH: 0.115,2.406 0.417,2.771 0.302,0.365 10 true LH:

Remove the 4 engine mounting insulator bolts.


d.

Lift the engine out from the vehicle slowly and carefully.

NOTICE:

Make sure the engine is clear of all wiring, hoses and cables.



Hide 17168 40.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 41.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 42.INSTALL ENGINE ON ENGINE STAND

a.

Install the engine onto an engine stand with the bolts.


b.

Remove the 2 bolts and 2 engine hangers.