Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  P0357  Ignition Coil "G" Primary / Secondary Circuit  P0358  Ignition Coil "H" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is set, check the No. 1 ignition coil circuit.

·

If DTC P0352 is set, check the No. 2 ignition coil circuit.

·

If DTC P0353 is set, check the No. 3 ignition coil circuit.

·

If DTC P0354 is set, check the No. 4 ignition coil circuit.

·

If DTC P0355 is set, check the No. 5 ignition coil circuit.

·

If DTC P0356 is set, check the No. 6 ignition coil circuit.

·

If DTC P0357 is set, check the No. 7 ignition coil circuit.

·

If DTC P0358 is set, check the No. 8 ignition coil circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A371072E02
4.104,1.24 3.865,0.5 3.865,0.5 3.729,0.5 false 5.469,0.458 4.969,0.688 false 2.531,0.917 2.938,1.115 0.406,0.198 10 false IGT1 2.51,1.344 2.906,1.531 0.396,0.188 10 false IGF1 2.521,2.323 2.927,2.521 0.406,0.198 10 false IGT2 2.531,2.698 2.938,2.896 0.406,0.198 10 false IGF2 2.51,3.198 2.917,3.396 0.406,0.198 10 false IGT3 2.542,4.063 2.927,4.26 0.385,0.198 10 false IGT4 2.542,4.948 2.927,5.146 0.385,0.198 10 false IGT5 2.531,5.813 2.917,6.01 0.385,0.198 10 false IGT6 2.542,6.688 2.927,6.885 0.385,0.198 10 false IGT7 2.542,7.552 2.927,7.75 0.385,0.198 10 false IGT8 2.448,8.083 2.833,8.281 0.385,0.198 10 false ECM 1.76,7.719 2.229,7.917 0.469,0.198 10 false TACH 1.094,7.563 1.698,7.76 0.604,0.198 10 false to DLC3 0.385,2.271 1.625,2.625 1.24,0.354 10 false Crankshaft Position Sensor 0.448,3.438 1.333,3.646 0.885,0.208 10 false VVT Sensor 0.396,4.635 1.573,5.01 1.177,0.375 10 false Camshaft Position Sensor 0.146,5.76 1.958,6.479 1.813,0.719 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 4.802,0.021 5.771,0.188 0.969,0.167 10 false from Battery 3.271,0.406 3.76,0.615 0.49,0.208 10 false Igniter 5.552,0.385 6.76,0.604 1.208,0.219 10 false No. 1 Ignition Coil 4.25,1.781 5.125,1.979 0.875,0.198 10 false Ignition Coil 5.521,1.031 6.604,1.229 1.083,0.198 10 false No. 1 Cylinder 5.875,1.688 6.646,1.885 0.771,0.198 10 false Spark Plug 3.958,2.323 5.167,2.542 1.208,0.219 10 false No. 2 Ignition Coil 3.969,3.198 5.177,3.417 1.208,0.219 10 false No. 3 Ignition Coil 3.958,4.073 5.167,4.292 1.208,0.219 10 false No. 4 Ignition Coil 3.938,4.927 5.146,5.146 1.208,0.219 10 false No. 5 Ignition Coil 3.938,5.813 5.146,6.031 1.208,0.219 10 false No. 6 Ignition Coil 3.938,6.688 5.146,6.906 1.208,0.219 10 false No. 7 Ignition Coil 3.948,7.583 5.156,7.802 1.208,0.219 10 false No. 8 Ignition Coil 5.688,7.99 6.698,8.208 1.01,0.219 10 false No. 8 Cylinder 5.656,7.115 6.667,7.333 1.01,0.219 10 false No. 7 Cylinder 5.635,6.24 6.646,6.458 1.01,0.219 10 false No. 6 Cylinder 5.635,5.344 6.646,5.563 1.01,0.219 10 false No. 5 Cylinder 5.635,4.5 6.646,4.719 1.01,0.219 10 false No. 4 Cylinder 5.615,3.625 6.625,3.844 1.01,0.219 10 false No. 3 Cylinder 5.635,2.74 6.646,2.958 1.01,0.219 10 false No. 2 Cylinder 0.156,0.073 2.115,0.292 1.958,0.219 10 false Reference (System Diagram):

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
No IGF signal to ECM while engine running
(1 trip detection logic)
·

Ignition system

·

Open or short in IGF1, IGF2 or IGT1 circuit (to 8) between ignition coil and ECM

·

No. 1 to No. 8 ignition coils

·

ECM



Reference: Inspection using an oscilloscope.

A379410E02
0.594,0.115 1.188,0.292 0.594,0.177 10 false 2 V/DIV. 0.604,0.896 0.979,1.073 0.375,0.177 10 false GND 0.594,1.458 0.969,1.635 0.375,0.177 10 false GND 0.865,0.719 1.177,0.906 0.313,0.188 10 false IGT 0.865,1.26 1.167,1.448 0.302,0.188 10 false IGF 1.833,1.813 2.854,1.99 1.021,0.177 10 false 20 msec./DIV.

Standard:
Tester Connection Tool Setting Condition Specified Condition
D74-40 (IGT1) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-33 (IGT2) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-37 (IGT3) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-34 (IGT4) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-35 (IGT5) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-36 (IGT6) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-38 (IGT7) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-39 (IGT8) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-104 (IGF1) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
D74-105 (IGF2) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown


HINT:

While cranking or idling the engine, check the waveform between terminals IGT1 (to 8) and E1, and IGF1 or IGF2 and E1 of the ECM connector.



MONITOR DESCRIPTION

A220081E04
4.716,2.416 5.483,2.600 0.767,0.184 10 Ignition Coil 4.118,1.542 4.781,1.726 0.663,0.184 10 Igniter 5.33,1.367 6.277,1.530 0.948,0.163 10 Ignition Coil 0.324,2.902 1.457,3.266 1.134,0.364 10 Ignition Signal (IGT) 0.331,3.624 1.170,4.171 0.840,0.547 10 Ignition Confirmation Signal (IGF) 1.61,3.511 2.169,3.688 0.559,0.177 10 Normal 1.386,3.896 2.167,4.073 0.781,0.177 10 Malfunction 3.66,4.52 4.608,4.707 0.947,0.187 10 Circuit Open 5.825,4.984 6.349,5.147 0.524,0.163 10 Time 1.805,1.668 2.203,1.843 0.398,0.175 10 ECM 2.918,1.337 3.245,1.522 0.326,0.186 10 IGT 2.918,1.751 3.245,1.936 0.326,0.186 10 IGF

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY

Related DTCs P0351: Igniter (cylinder 1) malfunction
P0352: Igniter (cylinder 2) malfunction
P0353: Igniter (cylinder 3) malfunction
P0354: Igniter (cylinder 4) malfunction
P0355: Igniter (cylinder 5) malfunction
P0356: Igniter (cylinder 6) malfunction
P0357: Igniter (cylinder 7) malfunction
P0358: Igniter (cylinder 8) malfunction
Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration -
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not stored None
Either of following conditions A or B met -
A. Engine speed 1500 rpm or less
B. Starter OFF
Either of following conditions C or D met -
C. Both of following conditions (a) and (b) met -
(a) Engine speed 500 rpm or less
(b) Battery voltage 6 V or more
D. All of following conditions (a), (b) and (c) met -
(a) Engine speed More than 500 rpm
(b) Battery voltage 10 V or more
(c) Number of sparks after CPU reset 5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS

All of the following conditions are met A, B, C and D
A. Ignition signal fail counter More than 2 times
B. Time after condition A is met 0.256 seconds or more
C. Ignition signal fail count after condition B is met More than 2 times
D. Ignition switch ON

COMPONENT OPERATING RANGE

IGF signal Igniter transmits IGF signal when it receives IGT signal from ECM

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353, P0354, P0355, P0356, P0357 or P0358.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A259910E01
5.377,0.841 5.713,1.011 0.336,0.170 10 IGT1 3.471,0.911 3.808,1.081 0.336,0.170 10 IGT1 5.377,2.508 5.713,2.678 0.336,0.170 10 IGT3 5.377,4.176 5.713,4.346 0.336,0.170 10 IGT5 5.377,5.843 5.713,6.013 0.336,0.170 10 IGT7 5.378,1.25 5.709,1.419 0.331,0.169 10 IGF1 3.473,1.32 3.804,1.489 0.331,0.169 10 IGF1 5.911,6.458 6.206,6.614 0.295,0.156 10 D74 5.121,0.841 5.305,0.997 0.184,0.156 10 40 5.121,2.508 5.305,2.664 0.184,0.156 10 37 5.121,4.176 5.305,4.332 0.184,0.156 10 35 5.121,5.843 5.305,5.999 0.184,0.156 10 38 5.037,1.25 5.304,1.406 0.267,0.156 10 104 5.902,6.612 6.266,6.796 0.364,0.184 10 ECM 3.853,0.831 3.968,0.987 0.114,0.156 10 3 3.856,1.228 3.991,1.391 0.135,0.163 10 2 2.891,0.835 2.991,0.991 0.100,0.156 10 1 2.897,1.227 3.011,1.383 0.114,0.156 10 4 2.813,1.58 3.107,1.736 0.295,0.156 10 D10 2.841,1.748 4.010,1.918 1.170,0.170 10 No. 1 Ignition Coil 3.051,0.909 3.262,1.063 0.211,0.154 10 +B 3.051,1.316 3.401,1.471 0.350,0.156 10 GND 3.471,2.593 3.808,2.762 0.336,0.170 10 IGT3 3.473,3.001 3.804,3.170 0.331,0.169 10 IGF2 3.853,2.512 3.968,2.668 0.114,0.156 10 3 3.856,2.909 3.991,3.072 0.135,0.163 10 2 2.891,2.502 2.991,2.658 0.100,0.156 10 1 2.897,2.909 3.011,3.065 0.114,0.156 10 4 2.813,3.261 3.107,3.417 0.295,0.156 10 D12 2.841,3.429 4.010,3.599 1.170,0.170 10 No. 3 Ignition Coil 3.051,2.59 3.262,2.744 0.211,0.154 10 +B 3.051,2.997 3.401,3.153 0.350,0.156 10 GND 3.471,4.26 3.808,4.430 0.336,0.170 10 IGT5 3.473,4.669 3.804,4.838 0.331,0.169 10 IGF2 3.853,4.18 3.968,4.335 0.114,0.156 10 3 3.856,4.576 3.991,4.739 0.135,0.163 10 2 2.891,4.184 2.991,4.340 0.100,0.156 10 1 2.897,4.576 3.011,4.732 0.114,0.156 10 4 2.813,4.928 3.107,5.084 0.295,0.156 10 D14 2.841,5.096 4.010,5.266 1.170,0.170 10 No. 5 Ignition Coil 3.051,4.258 3.262,4.411 0.211,0.154 10 +B 3.051,4.664 3.401,4.820 0.350,0.156 10 GND 3.471,5.927 3.808,6.097 0.336,0.170 10 IGT7 3.473,6.336 3.804,6.505 0.331,0.169 10 IGF1 3.853,5.847 3.968,6.003 0.114,0.156 10 3 3.856,6.244 3.991,6.407 0.135,0.163 10 2 2.891,5.837 2.991,5.993 0.100,0.156 10 1 2.897,6.243 3.011,6.399 0.114,0.156 10 4 2.813,6.595 3.107,6.751 0.295,0.156 10 D16 2.813,6.764 3.982,6.933 1.170,0.170 10 No. 7 Ignition Coil 3.051,5.925 3.262,6.079 0.211,0.154 10 +B 3.051,6.331 3.401,6.487 0.350,0.156 10 GND 1.657,0.515 1.905,0.671 0.248,0.156 10 INJ 0.139,0.118 1.119,0.302 0.980,0.184 10 from IG2 Relay 1.54,7.548 1.668,7.718 0.128,0.170 10 A 4.553,7.548 4.681,7.718 0.128,0.170 10 B 4.791,7.548 4.919,7.718 0.128,0.170 10 C

A259911E01
5.38,0.896 5.748,1.061 0.368,0.165 10 IGT2 5.38,2.559 5.748,2.724 0.368,0.165 10 IGT4 5.38,4.221 5.748,4.386 0.368,0.165 10 IGT6 5.38,5.903 5.748,6.068 0.368,0.165 10 IGT8 5.38,1.307 5.730,1.491 0.350,0.184 10 IGF2 5.945,6.661 6.240,6.826 0.295,0.165 10 D74 5.135,0.91 5.347,1.085 0.211,0.174 10 33 5.07,1.307 5.346,1.472 0.276,0.165 10 105 5.144,2.563 5.333,2.724 0.188,0.161 10 34 5.13,4.231 5.319,4.391 0.188,0.161 10 36 5.13,5.912 5.319,6.072 0.188,0.161 10 39 3.853,0.915 3.972,1.071 0.119,0.156 10 3 3.853,1.307 3.972,1.463 0.119,0.156 10 2 2.9,0.915 3.001,1.079 0.100,0.164 10 1 2.886,1.319 3.004,1.493 0.119,0.174 10 4 3.461,0.99 3.820,1.155 0.360,0.165 10 IGT2 3.078,0.999 3.298,1.155 0.221,0.156 10 +B 3.078,1.391 3.419,1.547 0.341,0.156 10 GND 3.451,1.391 3.802,1.547 0.350,0.156 10 IGF2 3.853,2.591 3.972,2.747 0.119,0.156 10 3 3.853,2.984 3.972,3.140 0.119,0.156 10 2 2.9,2.591 3.001,2.755 0.100,0.164 10 1 2.886,2.996 3.004,3.170 0.119,0.174 10 4 3.461,2.666 3.820,2.831 0.360,0.165 10 IGT4 3.078,2.675 3.298,2.831 0.221,0.156 10 +B 3.078,3.068 3.419,3.224 0.341,0.156 10 GND 3.451,3.068 3.802,3.224 0.350,0.156 10 IGF1 3.853,4.254 3.972,4.410 0.119,0.156 10 3 3.853,4.646 3.972,4.802 0.119,0.156 10 2 2.9,4.254 3.001,4.418 0.100,0.164 10 1 2.886,4.658 3.004,4.833 0.119,0.174 10 4 3.461,4.329 3.820,4.494 0.360,0.165 10 IGT6 3.078,4.338 3.298,4.494 0.221,0.156 10 +B 3.078,4.73 3.419,4.886 0.341,0.156 10 GND 3.451,4.73 3.802,4.886 0.350,0.156 10 IGF1 3.853,5.926 3.972,6.082 0.119,0.156 10 3 3.853,6.318 3.972,6.474 0.119,0.156 10 2 2.9,5.926 3.001,6.090 0.100,0.164 10 1 2.886,6.33 3.004,6.505 0.119,0.174 10 4 3.461,6.001 3.820,6.166 0.360,0.165 10 IGT8 3.078,6.01 3.298,6.166 0.221,0.156 10 +B 3.078,6.402 3.419,6.558 0.341,0.156 10 GND 3.451,6.402 3.802,6.558 0.350,0.156 10 IGF2 5.945,6.804 6.286,6.969 0.341,0.165 10 ECM 1.545,0.093 1.684,0.258 0.139,0.165 10 A 4.572,0.093 4.710,0.258 0.139,0.165 10 B 4.796,0.093 4.934,0.258 0.139,0.165 10 C 2.888,1.656 3.202,1.821 0.313,0.165 10 D25 2.888,1.805 4.035,1.989 1.147,0.184 10 No. 2 Ignition Coil 2.888,3.337 3.202,3.502 0.313,0.165 10 D23 2.888,3.487 4.035,3.670 1.147,0.184 10 No. 4 Ignition Coil 2.888,5 3.202,5.165 0.313,0.165 10 D21 2.888,5.149 4.035,5.333 1.147,0.184 10 No. 6 Ignition Coil 2.888,6.662 3.202,6.828 0.313,0.165 10 D19 2.888,6.812 4.035,6.996 1.147,0.184 10 No. 8 Ignition Coil

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL (POWER SOURCE)
U151439E01
0.092,0.103 2.444,0.458 2.353,0.355 10 Front view of wire harness connector: (to Ignition Coil) 0.204,2.489 0.482,2.631 0.278,0.142 10 D16 0.645,2.162 0.921,2.304 0.276,0.142 10 D21 0.201,2.162 0.477,2.304 0.276,0.142 10 D14 0.65,2.489 0.927,2.631 0.276,0.142 10 D19 0.204,1.497 0.482,1.639 0.278,0.142 10 D10 0.645,1.497 0.921,1.639 0.276,0.142 10 D25 0.201,1.824 0.477,1.966 0.276,0.142 10 D12 0.65,1.824 0.927,1.966 0.276,0.142 10 D23 1.032,2.676 1.436,2.813 0.404,0.137 10 +B (+) 1.937,2.676 2.526,2.813 0.589,0.137 10 GND (-) 1.341,2.154 1.303,2.635 false 2.132,2.111 2.193,2.624 false

a.

Disconnect the D10, D12, D14, D16, D19, D21, D23 or D25 ignition coil connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D10-4 (GND) - Body ground Always Below 1 Ω
D25-4 (GND) - Body ground Always Below 1 Ω
D12-4 (GND) - Body ground Always Below 1 Ω
D23-4 (GND) - Body ground Always Below 1 Ω
D14-4 (GND) - Body ground Always Below 1 Ω
D21-4 (GND) - Body ground Always Below 1 Ω
D16-4 (GND) - Body ground Always Below 1 Ω
D19-4 (GND) - Body ground Always Below 1 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D10-1 (+B) - D10-4 (GND) Ignition switch ON 11 to 14 V
D25-1 (+B) - D25-4 (GND) Ignition switch ON 11 to 14 V
D12-1 (+B) - D12-4 (GND) Ignition switch ON 11 to 14 V
D23-1 (+B) - D23-4 (GND) Ignition switch ON 11 to 14 V
D14-1 (+B) - D14-4 (GND) Ignition switch ON 11 to 14 V
D21-1 (+B) - D21-4 (GND) Ignition switch ON 11 to 14 V
D16-1 (+B) - D16-4 (GND) Ignition switch ON 11 to 14 V
D19-1 (+B) - D19-4 (GND) Ignition switch ON 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
a.

Disconnect the D10, D12, D14, D16, D19, D21, D23 or D25 ignition coil connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D10-2 (IGF1) - D74-104 (IGF1) Always Below 1 Ω
D25-2 (IGF2) - D74-105 (IGF2) Always Below 1 Ω
D12-2 (IGF2) - D74-105 (IGF2) Always Below 1 Ω
D23-2 (IGF1) - D74-104 (IGF1) Always Below 1 Ω
D14-2 (IGF2) - D74-105 (IGF2) Always Below 1 Ω
D21-2 (IGF1) - D74-104 (IGF1) Always Below 1 Ω
D16-2 (IGF1) - D74-104 (IGF1) Always Below 1 Ω
D19-2 (IGF2) - D74-105 (IGF2) Always Below 1 Ω
D10-3 (IGT1) - D74-40 (IGT1) Always Below 1 Ω
D25-3 (IGT2) - D74-33 (IGT2) Always Below 1 Ω
D12-3 (IGT3) - D74-37 (IGT3) Always Below 1 Ω
D23-3 (IGT4) - D74-34 (IGT4) Always Below 1 Ω
D14-3 (IGT5) - D74-35 (IGT5) Always Below 1 Ω
D21-3 (IGT6) - D74-36 (IGT6) Always Below 1 Ω
D16-3 (IGT7) - D74-38 (IGT7) Always Below 1 Ω
D19-3 (IGT8) - D74-39 (IGT8) Always Below 1 Ω
D10-2 (IGF1) or D74-104 (IGF1) - Body ground Always 10 kΩ or higher
D25-2 (IGF2) or D74-105 (IGF2) - Body ground Always 10 kΩ or higher
D12-2 (IGF2) or D74-105 (IGF2) - Body ground Always 10 kΩ or higher
D23-2 (IGF1) or D74-104 (IGF1) - Body ground Always 10 kΩ or higher
D14-2 (IGF2) or D74-105 (IGF2) - Body ground Always 10 kΩ or higher
D21-2 (IGF1) or D74-104 (IGF1) - Body ground Always 10 kΩ or higher
D16-2 (IGF1) or D74-104 (IGF1) - Body ground Always 10 kΩ or higher
D19-2 (IGF2) or D74-105 (IGF2) - Body ground Always 10 kΩ or higher
D10-3 (IGT1) or D74-40 (IGT1) - Body ground Always 10 kΩ or higher
D25-3 (IGT2) or D74-33 (IGT2) - Body ground Always 10 kΩ or higher
D12-3 (IGT3) or D74-37 (IGT3) - Body ground Always 10 kΩ or higher
D23-3 (IGT4) or D74-34 (IGT4) - Body ground Always 10 kΩ or higher
D14-3 (IGT5) or D74-35 (IGT5) - Body ground Always 10 kΩ or higher
D21-3 (IGT6) or D74-36 (IGT6) - Body ground Always 10 kΩ or higher
D16-3 (IGT7) or D74-38 (IGT7) - Body ground Always 10 kΩ or higher
D19-3 (IGT8) or D74-39 (IGT8) - Body ground Always 10 kΩ or higher




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Shuffle the arrangement of the ignition coil (among No. 1 to No. 8 cylinders).

NOTICE:

Do not shuffle the connectors.



e.

Perform a simulation test.


f.

Check DTCs displayed on the Techstream.

Result
Result Proceed to
Same DTC is output A
Different ignition coil DTC is output B

HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




A

B