Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P1613  Secondary Air Injection Driver Malfunction  P1614  Secondary Air Injection System Driver Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P1613
P1614
Either of following conditions (1) or (2) met:
(1) All of following conditions met (1 trip detection logic):
·

Either of air pump or air switching valve not operating

·

Diagnostic signal from Air Injection Control Driver (AID) 80%

·

Battery voltage 8 V or more


(2) Both of following conditions met (1 trip detection logic):
·

Battery voltage 8 V or more

·

Diagnostic signal from AID abnormal (duty signal other than 0, 20, 40, 80 and 100%)


·

AID

·

Open in AID ground circuit


P1613
P1614

All of following conditions met (1 trip detection logic):

1.

Air injection system operating (Air Switching Valve [ASV] ON and air pump ON)

2.

Diagnostic signal from Air Injection Control Driver (AID) 0%

3.

Battery voltage 8 V or more



·

Short in diagnostic information signal circuit (AID - ECM)

·

Open or short in air pump and air switching valve command signal circuit (AID - ECM)

·

Open in AID ground circuit

·

AID

·

ECM


P1613
P1614

Both of following conditions met (1 trip detection logic):

1.

Battery voltage 8 V or more

2.

Diagnostic signal from Air Injection Control Driver (AID) 100%



·

Open or short in AID +B circuit

·

Open in diagnostic information signal circuit (AID - ECM)

·

AID

·

ECM



MONITOR DESCRIPTION

For a short time after cold engine starts, the ECM transmits command signals to the Air Injection Control Driver (AID) to drive the air pump and the Air Switching Valve (ASV). The AID detects open and short circuits according to the voltages at the AID terminals to the air pump and ASV, and the circuit voltage of the AID power source, and transmits diagnostic information as a signal to the ECM.

If the Secondary Air Injection (AIR) system circuit or the AID itself malfunctions, the AID sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM sets the DTC based on the diagnostic information from the AID.

EXAMPLE:

1.

The duty ratio of the diagnostic signal from the AID is 0 or 100% (remains at 0 V or the same as battery voltage).

2.

The duty ratio of the diagnostic signal from the AID shows an impossible ratio (other than 0, 20, 40, 80 and 100%).

3.

The AID outputs the normal signal (normal duty signal: 80%) while the system is not operating.


MONITOR STRATEGY

Related DTCs P1613: Secondary air injection system air injection control driver circuit range check
P1614: Secondary air injection system air injection control driver circuit range check
Required Sensors/Components (Main) Air injection control driver
Required Sensors/Components (Related) Air switching valve
Frequency of Operation Once per drive cycle
Duration 3 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Case 1 and 4:
Monitor runs whenever following DTCs not stored None
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

Case 2:
Monitor runs whenever following DTCs not stored None
Either a or b met: -
a. Air pump Not operating
b. Air switching valve Not operating
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

Case 3:
Monitor runs whenever following DTCs not stored None
Following conditions (a) and (b) met -
a. Air pump Operating
b. Air switching valve Operating
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Case 1:
One of following conditions met: A, B, C or D
A. Diagnostic signal duty ratio from air injection control driver 1% or more, and 10% or less
B. Diagnostic signal duty ratio from air injection control driver 30%
C. Diagnostic signal duty ratio from air injection control driver 49%
D. Diagnostic signal duty ratio from air injection control driver 91% or more, and 99% or less

Case 2:
Diagnostic signal duty ratio from air injection control driver 70% or more, and 90% or less

Case 3:
Diagnostic signal duty ratio from air injection control driver 0%

Case 4:
Diagnostic signal duty ratio from air injection control driver 100%

COMPONENT OPERATING RANGE

Diagnostic signal duty ratio from air injection control driver 70% or more, and 90% or less when secondary air injection system operating.
0% when secondary air injection system not operating.

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the Techstream on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the Techstream initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the AIR system pending codes: Press the ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P1613 or P1614.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.



18.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613 OR P1614)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
P1613 and/or P1614 are output A
P1613 and/or P1614 and other DTCs are output B

If any DTCs other than P1613 and P1614 are output, troubleshoot those DTCs first.



A

2.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)

B

2.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)
A379562E01
1.708,0.917 2.146,1.146 0.438,0.229 4.969,0.927 5.396,1.167 0.427,0.24 2.198,1.813 2.479,2.281 true 5.521,1.771 5.813,2.167 true 0.531,0.115 2.854,0.49 2.323,0.375 10 false Front view of wire harness connector: (to AID for Bank 1) 4.052,0.094 6.375,0.469 2.323,0.375 10 false Front view of wire harness connector: (to AID for Bank 2) 1.802,0.948 2.094,1.135 0.292,0.188 10 false D50 5.063,0.969 5.354,1.156 0.292,0.188 10 false D54 2.542,2.25 2.833,2.438 0.292,0.188 10 false +B 5.75,2.188 6.115,2.385 0.365,0.198 10 false +B2

a.

Disconnect the D50 or D54 Air Injection Control Driver (AID) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D50-5 (+B) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)
D54-5 (+B2) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)




OK

3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)
a.

Disconnect the A24 or D74 ECM connector.


b.

Disconnect the D50 or D54 AID connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D74-54 (AIRP) - D50-4 (SIP) Always Below 1 Ω
D74-28 (AIRV) - D50-3 (SIV) Always Below 1 Ω
D74-53 (ARP2) - D54-4 (SIP2) Always Below 1 Ω
A24-43 (ARV2) - D54-3 (SIV2) Always Below 1 Ω
D74-30 (AIDI) - D50-2 (DI) Always Below 1 Ω
D74-29 (AID2) - D54-2 (DI2) Always Below 1 Ω
D50-1 (E) - Body ground Always Below 1 Ω
D54-1 (E2) - Body ground Always Below 1 Ω
D74-54 (AIRP) or D50-4 (SIP) - Body ground Always 10 kΩ or higher
D74-28 (AIRV) or D50-3 (SIV) - Body ground Always 10 kΩ or higher
D74-53 (ARP2) or D54-4 (SIP2) - Body ground Always 10 kΩ or higher
A24-43 (ARV2) or D54-3 (SIV2) - Body ground Always 10 kΩ or higher
D74-30 (AIDI) or D50-2 (DI) - Body ground Always 10 kΩ or higher
D74-29 (AID2) or D54-2 (DI2) - Body ground Always 10 kΩ or higher




OK

4.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
A379562E02
1.698,0.938 2.125,1.198 0.427,0.26 4.938,0.938 5.365,1.198 0.427,0.26 1.24,2.24 1.458,1.792 true 1.969,2.229 1.667,1.802 true 4.448,2.219 4.667,1.771 true 5.156,2.229 4.906,1.781 true 0.51,0.135 2.844,0.51 2.333,0.375 10 false Front view of wire harness connector: (to AID for Bank 1) 3.969,0.104 6.271,0.49 2.302,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 1.177,2.26 1.333,2.458 0.156,0.198 10 false E 1.958,2.25 2.198,2.427 0.24,0.177 10 false DI 4.354,2.24 4.604,2.458 0.25,0.219 10 false E2 5.104,2.25 5.406,2.438 0.302,0.188 10 false DI2 1.781,0.979 2.104,1.177 0.323,0.198 10 false D50 5.021,0.979 5.344,1.177 0.323,0.198 10 false D54

a.

Disconnect the D50 or D54 AID connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D50-2 (DI) - D50-1 (E) Ignition switch ON 11 to 14 V (near battery voltage)
D54-2 (DI2) - D54-1 (E2) Ignition switch ON 11 to 14 V (near battery voltage)




OK

5.PERFORM ACTIVE TEST USING TECHSTREAM

NG

5.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Disconnect the D50 or D54 AID connector.

A379565E01
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.104,1.344 1.365,1.521 0.26,0.177 10 false SIV 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRV 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D50 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.323,1.313 4.708,1.5 0.385,0.188 10 false SIV2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARV2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D54 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


b.

Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the AIR system forced operation while the engine is idling.


h.

Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


i.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D50-3 (SIV) - D50-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D54-3 (SIV2) - D54-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D50-3 (SIV) - D50-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D54-3 (SIV2) - D54-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



j.

Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.

A379565E02
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.094,1.344 1.354,1.521 0.26,0.177 10 false SIP 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRP 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D50 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.333,1.313 4.708,1.5 0.375,0.188 10 false SIP2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARP2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D54 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


k.

Connect the Techstream to the DLC3.


l.

Turn the ignition switch to ON and turn the Techstream on.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



n.

Start the engine.


o.

Perform the AIR system forced operation while the engine is idling.


p.

Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


q.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D50-4 (SIP) - D50-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D54-4 (SIP2) - D54-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D50-4 (SIP) - D50-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D54-4 (SIP2) - D54-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V




OK

6.REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)

NG

6.REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)
a.

Replace the air injection control driver (for bank 1 or bank 2) (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL).



NEXT

7.CONFIRM WHETHER DTC OUTPUT RECURS
7.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


g.

Start the engine after the Techstream initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


k.

Read DTCs.

Result
Result Proceed to
No DTC is output A
Other DTCs are output B


l.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





A

END

B