The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).
The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0111 | When either condition below is met:
1.
The intake air temperature change is small, from the previous trip warm-up to the following trip (2 trip detection logic). 2.
When the change in the intake air temperature after engine start is less than the threshold value. |
Mass air flow meter |
The ECM performs OBD II monitoring based on the values from the intake air temperature sensor. If there is no change of the sensor value within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects the stuck intake air temperature sensor value by performing monitoring after the ignition switch is turned off or the engine is started (short soak or long soak).
| Related DTCs | P0111: Intake air temperature sensor rationality (After engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start) |
| Required Sensors/Components (Main) | Intake Air Temperature (IAT) sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per driving cycle |
| Duration | - |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | None |
| Time after engine start | 10 seconds or more |
| Battery voltage | 10.5 V or more |
| ECT change since engine stop | -40°C (-40°F) or more |
| ECT before engine stop | 70°C (158°F) or more |
| Accumulated MAF amount before engine stop | 3240 g or more |
| Key-off duration | 30 minutes |
| Mass air flow meter circuit failure (P0102, P0103) | Not detected |
| Intake air temperature circuit failure (P0112, P0113) | Not detected |
| Engine coolant temperature sensor circuit failure (P0115, P0117, P0118) | Not detected |
| Soak timer circuit failure (P2610) | Not detected |
| Key-off duration | 5 hours |
| Time after engine start | 10 seconds or more |
| ECT | 70°C (158°F) or more |
| Accumulated MAF amount | 3240 g or more |
| Either of the following conditions 1 or 2 is met: | - |
| 1. Duration while engine load is low | 120 seconds or more |
| 2. Duration while engine load is high | 10 seconds or more |
| Mass air flow meter circuit failure (P0102, P0103) | Not detected |
| Intake air temperature circuit failure (P0112, P0113) | Not detected |
| Engine coolant temperature sensor circuit failure (P0115, P0117, P0118) | Not detected |
| Soak timer circuit failure (P2610) | Not detected |
| IAT change | Less than 1°C (2°F) |
| IAT change | Less than 1°C (2°F) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Idle the engine for 5 minutes or more [C].
During steps [A] through [C], if the change in the intake air temperature is below 1°C (1.8°F), the intake air temperature sensor (MAF meter) is malfunctioning. It is not necessary to continue this procedure.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0111.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [F].
Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].
Check the DTC judgment result again [F].
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [F] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Refer to DTC P0112 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0112).
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| P0111 and other DTCs are output | A |
| P0111 is output | B |
If any DTCs other than P0111 are output, troubleshoot those DTCs first.
Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
A
B