Home › Engine / Hybrid System › 3UR-FBE FUEL › FUEL TANK
RM27M0U _51 Engine / Hybrid System _049096 3UR-FBE FUEL _0233953 FUEL TANK A

3UR-FBE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77310A 4.REMOVE FUEL TANK CAP

Hide 77606 5.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)

a.

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the 2 bolts, 2 nuts and No. 1 fuel tank protector sub-assembly.



b.
A330902

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 6 nuts and No. 1 fuel tank protector sub-assembly.



Hide 77209D 6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A194631

Remove the bolt and disconnect the fuel pressure switching valve.


b.
A152240E01
2.267,4.09 3.051,4.261 0.784,0.171 10 Nylon Tube 1.067,4.177 1.572,4.349 0.505,0.171 10 O-Ring 0.167,4.278 0.861,4.449 0.694,0.171 10 Connector 1.149,2.991 1.738,3.163 0.590,0.171 10 Retainer 2.528,2.21 3.177,2.381 0.648,0.171 10 Lifting Up 0.23,2.904 0.541,3.075 0.311,0.171 10 Pipe 2.689,3.908 2.689,4.099 false 1.087,3.847 1.241,4.167 false 1.241,4.167 1.345,3.847 false 0.618,4.081 0.618,4.272 false 0.698,3.409 1.047,3.085 false 1.041,3.085 1.127,3.085 false 0.242,3.539 0.14,3.423 false 0.144,3.431 0.144,2.994 false 0.138,2.994 0.21,2.994 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Detach the lock claw by lifting up the cover as shown in the illustration.


ii.

Pinch and pull the return tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





c.
A330903E01
0.306,3.044 0.587,3.210 0.281,0.166 10 Tab 0.992,2.914 1.588,3.093 0.596,0.179 10 Retainer 2.634,1.82 3.165,2.013 0.531,0.193 10 Pull Up 0.855,2.223 1.322,2.441 1.322,2.441 1.322,2.892 false 0.789,2.746 0.789,2.965 0.789,2.965 0.468,2.965 false 0.468,2.745 0.468,3.024 false

for 144 L (38 US gal) Fuel Tank:

i.

Pull the tabs of the retainer and pull up as shown in the illustration.


ii.

Pull the return tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





Hide 77204A 7.DISCONNECT FUEL TANK RETURN TUBE

a.
A159750E01
2.07,4.089 2.854,4.260 0.784,0.171 10 Nylon Tube 1.064,4.176 1.569,4.347 0.505,0.171 10 O-Ring 0.164,4.277 0.859,4.448 0.694,0.171 10 Connector 1.165,2.99 1.755,3.161 0.590,0.171 10 Retainer 2.453,2.213 3.078,2.385 0.625,0.171 10 Lifting Up 0.227,2.902 0.538,3.074 0.311,0.171 10 Pipe 2.491,3.907 2.491,4.098 false 1.084,3.845 1.238,4.166 false 1.238,4.166 1.343,3.845 false 0.615,4.079 0.615,4.27 false 0.696,3.408 1.064,3.084 false 1.057,3.084 1.144,3.084 false 0.239,3.538 0.137,3.421 false 0.141,3.429 0.141,2.993 false 0.135,2.993 0.207,2.993 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Detach the lock claw by lifting up the cover as shown in the illustration.


ii.

Pinch and pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





b.
A330904E03
0.979,0.24 0.917,0.24 false 0.917,0.24 0.771,0.51 false 0.375,1.365 0.542,1.365 0.542,1.365 0.771,1.115 false 0.469,1.115 0.469,1.365 false 1.01,0.146 1.656,0.417 0.646,0.271 10 true Retainer 0.031,1.271 0.417,1.906 0.385,0.635 10 true Tab 2.552,0.24 3.063,0.417 0.51,0.177 10 false Pull Up

for 144 L (38 US gal) Fuel Tank:

i.

Pull the tabs of the retainer and pull up as shown in the illustration.


ii.

Pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





Hide 8.DISCONNECT VENT LINE HOSE

a.
A152244E04
1.99,0.146 2.26,0.354 0.271,0.208 10 true Up

Pull up the retainer and disconnect the vent line hose.

NOTICE:
·

Do not use any tools in this procedure.


·

Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.




Hide 9.DISCONNECT WIRE HARNESS

a.
A152242

Detach the harness clamp from the fuel tank assembly.


Hide 77213B 10.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A152252E06
2.688,3.958 2.688,4.156 false 0.552,4.115 0.552,4.333 false 0.708,3.396 1.083,3.042 1.083,3.042 1.24,3.042 false 0.25,3.542 0.302,2.979 0.302,2.979 0.458,2.979 false 1.104,3.865 1.104,4.146 1.104,4.146 1.5,4.146 false 1.333,3.865 1.333,4.156 false 2.323,4.167 3.104,4.375 0.781,0.208 10 false Nylon Tube 1.542,4.063 2.073,4.25 0.531,0.188 10 false O-Ring 0.167,4.354 0.865,4.521 0.698,0.167 10 false Connector 1.281,2.958 1.927,3.167 0.646,0.208 10 false Retainer 2.073,0.229 2.698,0.396 0.625,0.167 10 false Lifting up 0.49,2.906 0.844,3.094 0.354,0.188 10 false Pipe

Detach the lock claws by lifting up the cover as shown in the illustration.


b.

Disconnect the fuel tank breather tube from the inlet fuel tank pipe sub-assembly.


c.

Disconnect the fuel tank to filler pipe hose from the inlet fuel tank pipe sub-assembly.


d.

Detach the fuel tank to filler pipe hose and fuel tank breather tube from the No. 1 breather tube clamp.


Hide 77754 11.DISCONNECT OUTLET NO. 1 CANISTER HOSE

a.

Disconnect the outlet No. 1 canister hose from the inlet fuel tank pipe sub-assembly.


b.

Detach the hose from the No. 1 breather tube clamp.


Hide 77100 12.REMOVE FUEL TANK ASSEMBLY

a.

Set an engine lifter underneath the fuel tank assembly.


b.
A152248

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the 2 bolts, 2 clips, 2 pins, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.



c.
A330905

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 3 bolts, 3 clips, 3 pins, 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly.



d.

Slowly lower the engine lifter slightly.

NOTICE:

Be careful not to cut the wiring.



e.
A307675

w/ Cover:

Detach the 3 claws to remove the No. 2 fuel tank protector.


f.
A194632

Disconnect the wire harness clamp from the fuel tank assembly.


g.

Disconnect the fuel pump connector and fuel pressure switching valve connector, and then lower the engine lifter.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




Hide 77201 13.REMOVE INLET FUEL TANK PIPE SUB-ASSEMBLY

a.
A156396

Remove the 2 nuts and inlet fuel tank pipe sub-assembly.


Hide 77204A 14.REMOVE FUEL TANK RETURN TUBE

a.
U151626E02
1.479,3.667 1.198,3.667 1.198,3.667 1.198,3.792 true 0.969,2.802 1.135,2.802 1.135,2.802 1.25,3.396 false 1.375,2.427 1.438,2.427 1.438,2.427 1.552,3.01 false 2,3.021 2.115,2.313 2.115,2.313 2.292,2.313 false 0.188,3.719 0.729,3.938 0.542,0.219 10 false O-Ring 2.344,3.604 3.198,3.99 0.854,0.385 10 false Fuel Suction Plate 0.292,2.719 1.031,3.115 0.74,0.396 10 false Tube Joint Clip 0.396,2.333 1.438,2.542 1.042,0.208 10 false Fuel Tube Joint 2.344,2.24 3.198,2.625 0.854,0.385 10 false Fuel Tank Return Tube

Remove the tube joint clip and pull out the fuel tank return tube to remove it.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tube.




Hide 15.REMOVE FUEL PRESSURE SWITCHING VALVE ASSEMBLY

a.
A194622E03
1.49,3.667 1.219,3.667 1.219,3.667 1.219,3.802 true 1.49,3.813 0.865,3.813 true 2.271,3.781 1.938,3.781 false 1.25,3.396 1.063,2.979 1.063,2.979 0.906,2.979 false 1.563,3.01 1.385,2.583 1.385,2.583 1.302,2.583 false 2.417,2.521 2.292,2.521 2.292,2.521 1.99,3.031 false 0.354,2.51 1.375,2.729 1.021,0.219 10 true Fuel Tube Joint 0.24,2.896 0.958,3.281 0.719,0.385 10 false Tube Joint Clip 0.292,3.729 0.813,3.927 0.521,0.198 10 false O-Ring 2.333,3.688 3.167,4.104 0.833,0.417 10 false Fuel Suction Plate 2.448,2.354 3.167,2.729 0.719,0.375 10 true Fuel Tank Main Tube

Remove the 2 tube joint clips and pull out the 2 fuel tank main tubes. Then remove the fuel pressure switching valve assembly.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




Hide 77697 16.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A330923E01
2.777,2.42 3.072,2.595 0.295,0.174 10 Nut 2.92,1.655 2.92,2.391 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the nut from the No. 1 fuel tank heat insulator.


ii.

Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



b.
A330906E01
3.062,0.436 3.361,0.603 0.298,0.166 10 Nut 3.008,0.535 2.785,0.535 2.785,0.535 2.338,1.759 false 2.785,1.535 2.785,0.535 false

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 2 nuts from the No. 1 fuel tank heat insulator.


ii.

Using needle-nose pliers, remove the 2 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



Hide 77697A 17.REMOVE NO. 2 FUEL TANK HEAT INSULATOR (for 144 L (38 US gal) Fuel Tank)

a.
A330907

Using needle-nose pliers, remove the 3 clips shown in the illustration and then remove the No. 2 fuel tank heat insulator.


Hide 77213B 18.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A196277

Remove the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77020A 19.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77641A 20.REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Cover)

A307676

HINT:

Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.


a.

Detach the 4 clamps to remove the No. 1 fuel tank protector.