Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL INJECTOR
RM27M0U _51 Engine / Hybrid System _049097 3UR-FE FUEL _0233958 FUEL INJECTOR A

3UR-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the fuel pump ECU connector (see page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP ECU>REMOVAL).


c.

Connect the cable to the negative (-) battery terminal.


d.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

DTC P0171/0174 (system too lean) may be set.



e.

Crank the engine again, and then check that the engine does not start.


f.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


g.

Connect the fuel pump ECU connector (see page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP ECU>INSTALLATION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 23902 6.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A161418

Disconnect the No. 2 fuel tube from the fuel pressure regulator (for quick type A) (see page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23901 7.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A256329

Disconnect the fuel tube from the fuel delivery pipe RH (for quick type A) (see page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.
A161415

Disconnect the fuel tube from the fuel delivery pipe LH (for quick type A) (see page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23801P 8.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A308885

Detach the clamp.


b.

Disconnect the No. 1 fuel pipe from the fuel delivery pipe LH (for quick type B) (see page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 9.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH

a.
A161422

Disconnect the ventilation hose and No. 6 wire harness connector.


b.

Remove the No. 3 engine cover.


c.
A256330

Remove the 2 bolts and fuel delivery pipe RH.

NOTICE:

When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.



d.

Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head RH.


Hide 23808 10.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH

a.

Disconnect the No. 7 wire harness connector.


b.

Remove the No. 1 engine cover.


c.
A256331

Remove the 2 bolts and fuel delivery pipe LH.

NOTICE:

When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.



d.

Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head LH.


Hide 23250 11.REMOVE FUEL INJECTOR ASSEMBLY

a.
A161427

Remove the fuel injector from the fuel delivery pipe, and then disconnect the injector connector.

NOTICE:
A380111

For reinstallation, attach a tag or label to the injector shaft.



b.
A149190E01
2.549,1.735 3.077,1.909 0.527,0.173 10 O-Ring 2.852,1.454 2.852,1.704 false

Remove the O-ring from the fuel injector.


c.
A214317

Detach the 3 clamps and then remove the No. 6 wire harness from the delivery pipe RH.


d.
A214318

Detach the 3 clamps and then remove the No. 7 wire harness from the delivery pipe LH.