Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL TANK › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049097 3UR-FE FUEL _0233962 FUEL TANK A

3UR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77310A 4.REMOVE FUEL TANK CAP

Hide 77606 5.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)

a.

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the 2 bolts, 2 nuts and No. 1 fuel tank protector sub-assembly.



b.
A330902

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 6 nuts and No. 1 fuel tank protector sub-assembly.



Hide 77209D 6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A159750E01
2.07,4.089 2.854,4.260 0.784,0.171 10 Nylon Tube 1.064,4.176 1.569,4.347 0.505,0.171 10 O-Ring 0.164,4.277 0.859,4.448 0.694,0.171 10 Connector 1.165,2.99 1.755,3.161 0.590,0.171 10 Retainer 2.453,2.213 3.078,2.385 0.625,0.171 10 Lifting Up 0.227,2.902 0.538,3.074 0.311,0.171 10 Pipe 2.491,3.907 2.491,4.098 false 1.084,3.845 1.238,4.166 false 1.238,4.166 1.343,3.845 false 0.615,4.079 0.615,4.27 false 0.696,3.408 1.064,3.084 false 1.057,3.084 1.144,3.084 false 0.239,3.538 0.137,3.421 false 0.141,3.429 0.141,2.993 false 0.135,2.993 0.207,2.993 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Detach the lock claw by lifting up the cover as shown in the illustration.


ii.

Pinch and pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





b.
A330904E02
0.979,0.24 0.917,0.24 false 0.917,0.24 0.771,0.51 true 0.375,1.365 0.542,1.365 0.542,1.365 0.771,1.115 true 0.469,1.115 0.469,1.365 true 1.01,0.146 1.604,0.323 0.594,0.177 10 true Retainer 0.031,1.271 0.365,1.729 0.333,0.458 10 true Tab 2.552,0.24 3.063,0.417 0.51,0.177 10 false Pull Up

for 144 L (38 US gal) Fuel Tank:

i.

Pull the tabs of the retainer and pull up as shown in the illustration.


ii.

Pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





Hide 77204A 7.DISCONNECT FUEL TANK RETURN TUBE

a.
A152240E01
2.267,4.09 3.051,4.261 0.784,0.171 10 Nylon Tube 1.067,4.177 1.572,4.349 0.505,0.171 10 O-Ring 0.167,4.278 0.861,4.449 0.694,0.171 10 Connector 1.149,2.991 1.738,3.163 0.590,0.171 10 Retainer 2.528,2.21 3.177,2.381 0.648,0.171 10 Lifting Up 0.23,2.904 0.541,3.075 0.311,0.171 10 Pipe 2.689,3.908 2.689,4.099 false 1.087,3.847 1.241,4.167 false 1.241,4.167 1.345,3.847 false 0.618,4.081 0.618,4.272 false 0.698,3.409 1.047,3.085 false 1.041,3.085 1.127,3.085 false 0.242,3.539 0.14,3.423 false 0.144,3.431 0.144,2.994 false 0.138,2.994 0.21,2.994 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Detach the lock claw by lifting up the cover as shown in the illustration.


ii.

Pinch and pull the return tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





b.
A330903E01
0.306,3.044 0.587,3.210 0.281,0.166 10 Tab 0.992,2.914 1.588,3.093 0.596,0.179 10 Retainer 2.634,1.82 3.165,2.013 0.531,0.193 10 Pull Up 0.855,2.223 1.322,2.441 1.322,2.441 1.322,2.892 false 0.789,2.746 0.789,2.965 0.789,2.965 0.468,2.965 false 0.468,2.745 0.468,3.024 false

for 144 L (38 US gal) Fuel Tank:

i.

Pull the tabs of the retainer and pull up as shown in the illustration.


ii.

Pull the return tube connector to disconnect the connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.





Hide 8.DISCONNECT VENT LINE HOSE

a.
A152244E04
1.99,0.146 2.26,0.354 0.271,0.208 10 true Up

Pull up the retainer and disconnect the vent line hose.

NOTICE:
·

Do not use any tools in this procedure.


·

Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.




Hide 9.DISCONNECT WIRE HARNESS

a.
A152242

Detach the harness clamp from the fuel tank assembly.


Hide 77213B 10.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A152252E01
2.186,4.101 2.970,4.272 0.784,0.171 10 Nylon Tube 1.064,4.178 1.569,4.350 0.505,0.171 10 O-Ring 0.164,4.279 0.859,4.450 0.694,0.171 10 Connector 1.107,2.973 1.697,3.144 0.590,0.171 10 Retainer 2.011,0.233 2.632,0.404 0.621,0.171 10 Lifting Up 0.227,2.905 0.538,3.076 0.311,0.171 10 Pipe 2.608,3.919 2.608,4.11 false 1.084,3.848 1.238,4.168 false 1.238,4.168 1.343,3.848 false 0.615,4.082 0.615,4.273 false 0.696,3.41 1.005,3.066 false 0.999,3.066 1.085,3.066 false 0.239,3.54 0.137,3.424 false 0.141,3.432 0.141,2.995 false 0.135,2.995 0.207,2.995 false

Detach the lock claw by lifting up the cover as shown in the illustration.


b.

Disconnect the fuel tank breather tube from the inlet fuel tank pipe sub-assembly.


c.

Disconnect the fuel tank to filler pipe hose from the inlet fuel tank pipe sub-assembly.


d.

Detach the filler pipe hose and fuel tank breather tube from the No. 1 breather tube clamp.


Hide 77754 11.DISCONNECT OUTLET NO. 1 CANISTER HOSE

a.

Disconnect the outlet No. 1 canister hose from the inlet fuel tank pipe sub-assembly.


b.

Detach the hose from the No. 1 breather tube clamp.


Hide 77100 12.REMOVE FUEL TANK ASSEMBLY

a.

Set an engine lifter underneath the fuel tank assembly.


b.
A152248

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the 2 bolts, 2 clips, 2 pins, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.



c.
A330905

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 3 bolts, 3 clips, 3 pins, 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly.



d.

Slowly lower the engine lifter slightly.

NOTICE:

Be careful not to cut the wiring.



e.
A307675

w/ Cover:

Detach the 3 claws and remove the No. 2 fuel tank protector.


f.
A152243

Detach the wire harness clamp from the fuel tank assembly as shown in the illustration.


g.

Disconnect the fuel pump connector and lower the engine lifter.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




Hide 77201 13.REMOVE INLET FUEL TANK PIPE SUB-ASSEMBLY

a.
A156396

Remove the 2 nuts and inlet fuel tank pipe sub-assembly.


Hide 77697 14.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A152249E01
2.809,2.367 3.093,2.547 0.284,0.180 10 Nut 2.935,1.639 2.935,2.362 false

for 100 L (26.4 US gal) Fuel Tank:

i.

Remove the nut from the No. 1 fuel tank heat insulator.


ii.

Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



b.
A330911E01
3.021,0.602 3.325,0.781 0.304,0.179 10 Nut 2.981,0.69 2.785,0.69 2.785,0.69 2.336,1.759 false 2.785,1.535 2.785,0.69 false

for 144 L (38 US gal) Fuel Tank:

i.

Remove the 2 nuts from the No. 1 fuel tank heat insulator.


ii.

Using needle-nose pliers, remove the 2 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



Hide 77697A 15.REMOVE NO. 2 FUEL TANK HEAT INSULATOR (for 144 L (38 US gal) Fuel Tank)

a.
A330912

Using needle-nose pliers, remove the 3 clips shown in the illustration and then remove the No. 2 fuel tank heat insulator.


Hide 77213B 16.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A152251

Remove the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77020A 17.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A152246E04
1.938,3.833 2.49,3.927 false 2.49,3.927 2.49,3.99 false 1.458,3.667 1.021,3.906 false 1.01,3.906 1.51,3.813 false 1.26,3.385 1.198,3.115 false 1.448,3.135 1.313,2.708 false 1.198,3.115 1.167,3.115 false 1.969,3.031 2.115,2.656 false 2.115,2.656 2.167,2.656 false 1.323,2.708 1.219,2.708 false 1.99,4 3.156,4.167 1.167,0.167 10 false Fuel Suction Plate 2.219,2.583 3.219,2.75 1,0.167 10 false Fuel Tank Tube 0.458,3.802 0.958,3.969 0.5,0.167 10 false O-Ring 0.021,3.01 0.979,3.177 0.958,0.167 10 false Tube Joint Clip 0.385,2.625 1.104,2.792 0.719,0.167 10 false Tube Joint

Remove the 2 tube joint clips and pull out the fuel tank main tube sub-assembly and fuel tank return tube.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank tubes.




b.
A259584E04
2.813,0.219 2.656,0.219 2.656,0.219 2.417,0.479 false 2.844,0.135 3.167,0.344 0.323,0.208 10 true SST

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Securely attach the claws of SST to the protrusion of the retainer and fix SST in place.

·

Install SST while pressing the claws of SST against the retainer (towards the center of SST).




c.
A259581E03
0.51,1.563 0.615,1.563 0.615,1.563 0.948,1.146 false 0.135,1.479 0.552,1.75 0.417,0.271 10 true SST

Using SST, loosen the retainer.

SST
09808-14030  

NOTICE:
·

Do not use any tools other than those specified in this operation. Damage to the retainer or the fuel tank assembly may result.

·

While pressing down on SST so that the claws of SST do not slip off the protrusion of the retainer, turn the retainer counterclockwise to loosen it.



HINT:

The protrusions of the retainer fit in the ends of SST.



d.

Remove the retainer.


e.

Remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



f.

Remove the gasket from the fuel tank assembly.


Hide 77641A 18.REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Cover)

A307676

HINT:

Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.


a.

Detach the 4 clamps to remove the No. 1 fuel tank protector.