Home › Engine / Hybrid System › 1UR-FE FUEL › FUEL PUMP › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049098 1UR-FE FUEL _0233968 FUEL PUMP A

1UR-FE FUEL  FUEL PUMP  REMOVAL  


PROCEDURE

Hide 77100 1.REMOVE FUEL TANK ASSEMBLY

a.

Remove the fuel tank (See page Engine / Hybrid System>1UR-FE FUEL>FUEL TANK>REMOVAL).


Hide 77020A 2.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A152246E03
1.938,3.833 2.49,3.927 false 2.49,3.927 2.49,3.99 false 1.479,3.656 1.042,3.896 false 1.042,3.896 1.542,3.802 false 1.26,3.385 1.198,3.115 false 1.448,3.135 1.313,2.708 false 1.198,3.115 1.167,3.115 false 1.979,3.031 2.115,2.656 false 2.115,2.656 2.167,2.656 false 1.323,2.708 1.219,2.708 false 1.99,4 3.156,4.167 1.167,0.167 10 false Fuel Suction Plate 2.26,2.583 3.26,2.75 1,0.167 10 false Fuel Tank Tube 0.458,3.802 0.958,3.969 0.5,0.167 10 false O-Ring 0.198,3.021 1.156,3.188 0.958,0.167 10 false Tube Joint Clip 0.521,2.625 1.24,2.792 0.719,0.167 10 false Tube Joint

Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A259584E02
2.813,0.219 2.656,0.219 2.656,0.219 2.417,0.479 true 2.844,0.135 3.167,0.344 0.323,0.208 10 true SST

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Securely attach the claws of SST to the protrusion of the fuel pump gauge retainer and fix SST in place.

·

Install SST while pressing the claws of SST against the fuel pump gauge retainer (towards the center of SST).




c.
A259581E02
0.51,1.563 0.615,1.563 0.615,1.563 0.948,1.146 false 0.135,1.479 0.49,1.688 0.354,0.208 10 true SST

Using SST, loosen the retainer.

SST
09808-14030  

NOTICE:
·

Do not use any tools other than those specified in this operation. Damage to the retainer or the fuel tank may result.

·

While pressing down on SST so that the claws of SST do not slip off the protrusion of the retainer, turn the retainer counterclockwise to loosen it.



HINT:

The protrusions of the retainer fit in the ends of SST.



d.

Remove the retainer.


e.

Remove the fuel suction with pump and gauge tube assembly from the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



f.

Remove the gasket from the fuel tank.