Home › Engine / Hybrid System › 1UR-FE FUEL › FUEL TANK
RM27M0U _51 Engine / Hybrid System _049098 1UR-FE FUEL _0233970 FUEL TANK A

1UR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77310A 4.REMOVE FUEL TANK CAP

Hide 77606 5.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)

a.

Remove the 2 bolts, 2 nuts and No. 1 fuel tank protector sub-assembly.


Hide 77209D 6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A159750E04
2.458,3.948 2.458,4.135 false 0.615,4.104 0.615,4.292 false 1.052,3.052 1.146,3.052 false 0.26,3.552 0.083,2.958 0.083,2.958 0.208,2.958 false 0.677,3.438 1.063,3.052 true 1.083,3.854 1.229,4.177 true 1.229,4.188 1.323,3.854 true 2.365,4.167 2.563,4.344 0.198,0.177 10 false *5 1.115,4.229 1.302,4.417 0.188,0.188 10 false *4 0.5,4.323 0.719,4.521 0.219,0.198 10 false *3 1.167,2.969 1.396,3.188 0.229,0.219 10 false *2 2.448,2.188 2.698,2.406 0.25,0.219 10 false *a 0.229,2.875 0.427,3.052 0.198,0.177 10 false *1

a.

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Pipe
*2 Retainer
*3 Connector
*4 O-Ring
*5 Nylon Tube
*a Lifting Up


b.

Pinch and pull the fuel tank main tube connector to disconnect the fuel tank main tube sub-assembly from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 77204A 7.DISCONNECT FUEL TANK RETURN TUBE

A152240E04
2.458,3.948 2.458,4.135 false 0.625,4.115 0.625,4.302 false 1.073,3.063 1.156,3.063 false 0.271,3.552 0.094,2.958 0.094,2.958 0.219,2.958 false 0.677,3.427 1.073,3.063 true 1.083,3.854 1.219,4.177 true 1.229,4.188 1.323,3.854 true 2.375,4.146 2.573,4.323 0.198,0.177 10 false *5 1.146,4.24 1.333,4.427 0.188,0.188 10 false *4 0.542,4.323 0.76,4.521 0.219,0.198 10 false *3 1.177,2.979 1.406,3.198 0.229,0.219 10 false *2 2.469,2.188 2.719,2.406 0.25,0.219 10 false *a 0.24,2.875 0.438,3.052 0.198,0.177 10 false *1

a.

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Pipe
*2 Retainer
*3 Connector
*4 O-Ring
*5 Nylon Tube
*a Lifting Up


b.

Pinch and pull the fuel tank return tube connector to disconnect the fuel tank return tube from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 8.DISCONNECT VENT LINE HOSE

a.
A152244E03
1.979,0.177 2.167,0.396 0.188,0.219 10 false *a

Pull up the retainer and disconnect the vent line hose.

Text in Illustration
*a Up

NOTICE:
·

Do not use any tools in this procedure.


·

Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.




Hide 9.DISCONNECT WIRE HARNESS

a.
A152242

Detach the harness clamp from the fuel tank assembly.


Hide 77213B 10.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A152252E05
2.479,3.958 2.479,4.146 false 0.615,4.104 0.615,4.292 false 1.052,3.063 1.146,3.063 false 0.271,3.531 0.094,2.979 0.094,2.979 0.219,2.979 false 0.688,3.417 1.063,3.094 false 1.083,3.865 1.229,4.188 false 1.229,4.177 1.323,3.844 false 2.365,4.167 2.563,4.344 0.198,0.177 10 false *5 1.115,4.198 1.302,4.385 0.188,0.188 10 false *4 0.5,4.323 0.719,4.521 0.219,0.198 10 false *3 1.167,2.969 1.396,3.188 0.229,0.219 10 false *2 2.917,0.313 3.167,0.531 0.25,0.219 10 false *a 0.229,2.875 0.427,3.052 0.198,0.177 10 false *1

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Pipe
*2 Retainer
*3 Connector
*4 O-Ring
*5 Nylon Tube
*a Lifting Up


b.

Disconnect the fuel tank breather tube from the inlet fuel tank pipe sub-assembly.


c.

Disconnect the fuel tank to filler pipe hose from the inlet fuel tank pipe sub-assembly.


d.

Detach the filler pipe hose and fuel tank breather tube from the No. 1 breather tube clamp.


Hide 77754 11.DISCONNECT OUTLET NO. 1 CHARCOAL CANISTER HOSE

a.

Disconnect the outlet No. 1 charcoal canister hose from the inlet fuel tank pipe sub-assembly.


b.

Detach the hose from the No. 1 breather tube support.


Hide 77100 12.REMOVE FUEL TANK ASSEMBLY

a.

Set a transmission jack underneath the fuel tank assembly.


b.
A152248

Remove the 2 bolts, 2 clips, 2 pins, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.


c.

Slowly lower the transmission jack slightly.

NOTICE:

Be careful not to cut the wiring.



d.
A307675

w/ Cover:

Detach the 3 claws to remove the No. 2 fuel tank protector.


e.
A152243

Detach the wire harness clamp from the fuel tank assembly as shown in the illustration.


f.

Disconnect the fuel pump and fuel sender gauge connector and lower the transmission jack.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




Hide 77201 13.REMOVE INLET FUEL TANK PIPE SUB-ASSEMBLY

a.
A156396

Remove the 2 nuts and inlet fuel tank pipe sub-assembly.


Hide 77697 14.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

A152249E03
2.809,2.33 3.032,2.540 0.223,0.210 10 *1 2.935,1.603 2.935,2.325 false

a.

Remove the nut from the No. 1 fuel tank heat insulator.

Text in Illustration
*1 Nut


b.

Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.


Hide 77213B 15.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A152251

Remove the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77020A 16.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77641A 17.REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Cover)

A307676

HINT:

Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.


a.

Detach the 4 clamps to remove the No. 1 fuel tank protector.