Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › DRIVE BELT
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234033 DRIVE BELT A

1UR-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.
A217532E02
0.323,0.5 0.198,0.5 0.198,0.5 0.688,1.302 false 1.531,0.917 1.604,0.448 1.604,0.448 1.688,0.448 false 2.948,0.542 2.865,0.542 2.865,0.542 2.542,0.813 false 0.865,1.979 1.052,1.979 1.052,1.979 1.094,1.771 false 1.229,2.271 1.396,2.271 1.396,2.271 1.198,1.354 false 2.208,4.26 1.542,4.26 1.542,4.26 1.188,3.625 false 1.938,2.042 1.938,1.771 false 2.844,3.458 2.844,3.25 2.844,3.25 2.552,3.104 false 2.417,3.906 1.979,3.906 false 0.323,3.865 0.323,3.729 0.323,3.729 0.698,3.583 false 1.031,3.021 1.24,3.021 1.24,3.021 1.552,3.177 false 2.781,2.25 2.781,1.76 false 1.094,4.344 1.094,4.021 false 1.729,0.365 2.563,0.552 0.833,0.188 10 false Water Pump 0.385,0.417 1.146,0.615 0.76,0.198 10 false Vane Pump 1.885,2.25 3.135,2.448 1.25,0.198 10 false Cooler Compressor 0.052,1.875 0.719,2.042 0.667,0.167 10 false Generator 2.052,0.938 2.344,1.104 0.292,0.167 10 false Fan 1.604,2.052 2.333,2.24 0.729,0.188 10 false Crankshaft 0.083,2.167 1.01,2.333 0.927,0.167 10 false Belt Tensioner 2.99,0.458 3.354,0.781 0.365,0.323 10 false No. 1 Idler 0.021,0 2.156,0.26 2.135,0.26 12 false w/ Air Conditioning System: 0.021,2.542 2.229,2.802 2.208,0.26 12 false w/o Air Conditioning System: 2.042,3.188 2.333,3.354 0.292,0.167 10 false Fan 0.74,4.354 1.406,4.521 0.667,0.167 10 false Generator 2.26,4.167 3.198,4.323 0.938,0.156 10 false Belt Tensioner 2.448,3.823 3.177,4.01 0.729,0.188 10 false Crankshaft 2.51,3.479 3.24,3.667 0.729,0.188 10 false No. 1 Idler 0.135,3.875 0.573,4.271 0.438,0.396 10 false Vane Pump 0.021,2.917 0.854,3.104 0.833,0.188 10 false Water Pump

Set the V belt onto every part.


b.

While turning the belt tensioner counterclockwise, remove the pin.

NOTICE:

Make sure that the V belt is properly set to each pulley.



c.
A174124E01
0.231,1.304 1.012,1.497 0.781,0.193 10 CORRECT 1.911,1.304 2.817,1.465 0.906,0.161 10 INCORRECT

After installing the belt, check that it fits properly in the ribbed grooves.

HINT:

Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.