Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234042 ENGINE ASSEMBLY A

1UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly RH, cylinder head sub-assembly LH, No. 1 camshaft sub-assembly, No. 2 camshaft sub-assembly, No. 3 camshaft sub-assembly, No. 4 camshaft sub-assembly, camshaft timing gear RH, camshaft timing gear LH, camshaft timing exhaust gear RH, camshaft timing exhaust gear LH, piston or piston ring (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.REMOVE ENGINE FROM ENGINE STAND

a.
A217476

Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Engine hanger 12281-38150
Bolt 90119-A0166



b.

Attach an engine sling device and hang the engine with a chain block.


c.

Remove the bolts and engine assembly from the engine stand.


Hide 2.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.

NOTICE:

Make sure that the engine is clear of all wiring and hoses.



b.

Attach the engine mounting insulators to the vehicle.


c.
A214577E03
0.104,0.094 0.458,0.563 0.354,0.469 10 true RH: 0.104,2.396 0.427,2.875 0.323,0.479 10 true LH:

Install the 4 engine mounting insulator bolts.

Torque:
79 N*m (806 kgf*cm, 58 ft.*lbf)


d.

Remove the 2 bolts and 2 engine hangers.


Hide 32101 3.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E01
0.9,1.607 1.201,1.763 0.302,0.156 10 SST 0.831,1.237 1.049,1.572 1.049,1.572 1.089,1.108 false

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A217514C02
0,0 0,0 false
V100135

Engine Side


Install the crankshaft angle sensor rotor.

HINT:
·

Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.

·

As the crankshaft angle sensor rotor is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.
A217515C02
1.865,3.385 2.625,3.125 2.625,3.125 2.76,3.125 false 1.177,0.417 1.76,0.25 1.76,0.25 1.896,0.25 false 1.958,0.177 2.271,0.333 0.313,0.156 10 false *1 2.844,3.042 3.156,3.198 0.313,0.156 10 false *2
*1 Drive Plate
*2 Rear Drive Plate Spacer
V100135

Automatic Transmission Side


Install the drive plate and rear drive plate spacer onto the crankshaft.

HINT:

As the rear drive plate spacer and the drive plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



d.

Install the drive plate and ring gear and bolts.

HINT:

The bolts are tightened in 2 progressive steps.


i.

Clean the bolts and bolt holes.


ii.
A380777C01
1.833,1.188 2.052,0.479 2.052,0.479 2.198,0.479 false 2.26,0.406 2.573,0.563 0.313,0.156 10 false *1
*1 Adhesive


Apply adhesive to 2 or 3 threads of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



iii.
A214574E02
1.49,0.448 1.594,0.594 0.104,0.146 10 true 9 1.844,0.448 1.938,0.604 0.094,0.156 10 true 1 1.5,1.625 1.594,1.802 0.094,0.177 10 true 2 2.25,1.052 2.365,1.198 0.115,0.146 10 true 3 1.094,1.031 1.188,1.188 0.094,0.156 10 true 4 2.188,1.375 2.302,1.521 0.115,0.146 10 true 5 1.167,0.708 1.281,0.865 0.115,0.156 10 true 6 2.177,0.719 2.302,0.875 0.125,0.156 10 true 7 1.167,1.375 1.26,1.521 0.094,0.146 10 true 8 1.813,1.625 1.99,1.771 0.177,0.146 10 true 10

Step 1:

Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not reuse the drive plate installation bolts.

·

Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.




iv.

Mark the top of each drive plate installation bolt with paint.


v.

Step 2:

Tighten the drive plate installation bolts 90° as shown in the illustration.


vi.

Check that the painted marks are now at a 90° angle to the top.

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.




Hide 12371 4.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)

Hide 12371 5.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)

Hide 35000 6.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

Hide 17104 9.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 10.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 11.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 12.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25601 13.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 11452 14.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16268 15.CONNECT NO. 1 WATER BY-PASS PIPE

a.
A214575

Connect the No. 1 water by-pass pipe with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 17410 16.INSTALL EXHAUST PIPE ASSEMBLY

a.

Install the exhaust pipe assembly (See page Engine / Hybrid System>1UR-FE EXHAUST>EXHAUST PIPE>INSTALLATION).


Hide 37140 17.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

a.

Install the front propeller shaft (See page Drivetrain>PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>INSTALLATION).


Hide 37110 18.INSTALL PROPELLER SHAFT ASSEMBLY

a.

for 2WD:

Refer to the following procedures (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 2WD)>INSTALLATION).


b.

for 4WD:

Refer to the following procedures (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>INSTALLATION).


Hide 88320 21.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 22.CONNECT WIRE HARNESS AND HOSE

a.
A163790

Connect the 2 connectors and 2 clips to the engine room junction block.


b.

Install the engine wire with the nut. Then connect the 2 clips.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 4 air injection control driver connectors.


d.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the cable to the positive (+) battery terminal.


f.

Install the wire to the positive (+) battery cable with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


g.
A214573

Connect the air injection system hose.


h.

Install the connector bracket with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


i.

Connect the 2 clamps and air pump connector.


j.

Connect the clamp and ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


k.
U151465

Connect the 4 connectors to the connector holder block.


l.
A214851

Connect the 2 heater hoses.


m.
A214858

Connect the No. 4 water by-pass hose.


n.
A214862

Connect the ECM connector and clamp.

HINT:

Refer to the following procedures to connect the ECM connector (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>ECM>INSTALLATION).



Hide 23902 23.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel tube (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23801P 24.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A308865

Connect the No. 1 fuel pipe (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Install the fuel pipe clamp.


Hide 16261L 30.CONNECT NO. 13 WATER BY-PASS HOSE

Hide 53294C 35.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 36.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 53101 37.INSTALL RADIATOR GRILLE SUB-ASSEMBLY

Hide 16571 39.INSTALL INLET RADIATOR HOSE

Hide 53739A 40.INSTALL FRONT FENDER APRON SEAL REAR LH

Hide 53737B 41.INSTALL FRONT FENDER APRON SEAL LH

Hide 42.INSTALL FRONT FENDER APRON SEAL REAR RH

Hide 53736 43.INSTALL FRONT FENDER APRON SEAL RH

Hide 55701J 44.INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

Hide 17700 45.INSTALL AIR CLEANER ASSEMBLY

a.
A309638E02
0.031,0.042 0.917,0.51 0.885,0.469 10 true for Type A: 0.031,2.24 0.917,2.719 0.885,0.479 10 true for Type B:

Install the air cleaner case with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the air cleaner element to the air cleaner case.


c.
A309637E02
0.052,0.042 0.948,0.531 0.896,0.49 10 true for Type A: 0.052,2.229 0.938,2.667 0.885,0.438 10 true for Type B:

Install the air cleaner cap.

i.

for Type A:

Install the air cleaner cap and fasten the 4 hook clamps.


ii.

for Type B:

Install the air cleaner cap and fasten the 2 hook clamps.


iii.

Connect the MAF meter connector.


iv.

Attach the wire harness clamp.



Hide 17880 46.INSTALL AIR CLEANER HOSE ASSEMBLY

a.
A214569

Install the air cleaner hose with the 2 clamps.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Connect the ventilation hose and vacuum sensing hose.


Hide 49.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 54.INSPECT SHIFT LEVER POSITION

Hide 11209 55.INSTALL V-BANK COVER SUB-ASSEMBLY

a.
A214821E02
2.708,0.354 2.865,0.354 2.865,0.354 2.667,0.635 false 2.271,1.063 2.354,1.313 2.354,1.313 2.469,1.313 false 0.948,1.438 1.167,1.438 false 0.573,0.677 0.448,0.677 0.448,0.677 0.635,1.188 false 1.198,1.365 1.469,1.552 0.271,0.188 10 false Pin 0.594,0.594 1.24,0.781 0.646,0.188 10 false Grommet 2.188,0.281 2.719,0.479 0.531,0.198 10 false Bracket 2.5,1.25 2.875,1.427 0.375,0.177 10 false Hook

Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.


Hide 53301 56.INSTALL HOOD SUB-ASSEMBLY

a.
A308967

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Attach the lower part of the 2 hood supports to the hood support bolt ball joints.

CAUTION:

Install the hood support while supporting the hood by hand.



c.

Attach the hood support clips.

NOTICE:

Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



Hide 53301 57.ADJUST HOOD SUB-ASSEMBLY

Hide 59.INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

a.

Install the front wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).