Home › Drivetrain › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM
RM27M0U _52 Drivetrain _049120 TIRE AND WHEEL _0234088 TIRE PRESSURE WARNING SYSTEM J

TIRE AND WHEEL  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU detects a disconnected connector or an open circuit between the tire pressure warning ECU and combination meter, the tire pressure warning light turns off 10 seconds after the ignition switch is turned ON, blinks for 1 minute, and then remains on. Connecting terminals TC and CG of the DLC3 makes the tire pressure warning light blink and output the DTC.

WIRING DIAGRAM

C171956E15
5.625,0.885 5.771,1.052 0.146,0.167 10 false 5 5.906,1.01 6.302,1.188 0.396,0.177 10 false IND 5.375,1.76 7.156,2.104 1.781,0.344 10 false Tire Pressure Warning ECU 1.531,0.875 1.74,1.063 0.208,0.188 10 false 13 0.354,1.875 1.75,2.083 1.396,0.208 10 false Combination Meter 5.375,1.563 5.635,1.74 0.26,0.177 10 false J31 0.354,1.688 0.667,1.875 0.313,0.188 10 false J28 1.052,1.01 1.417,1.177 0.365,0.167 10 false TIRE

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (COMBINATION METER)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Start the engine.


e.

Enter the following menus: Body / Combination Meter / Active Test.


f.

Check the condition of the tire pressure warning light by operating the tester.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light ON or OFF Perform the test with the vehicle stopped and engine idling

OK:

The warning light turns on/off when operating the Techstream.




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECU)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECU)
a.

Disconnect the J31 ECU connector.


b.

Disconnect the J28 meter connector.


c.
U152204E02
1.979,1.719 2.448,1.792 true 2.188,3.792 2.135,4.25 true 0.344,0.198 2.74,0.708 2.396,0.51 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.375,2.49 2.656,3.01 2.281,0.521 10 false Front view of wire harness connector: (to Combination Meter) 0.74,1.188 1.031,1.385 0.292,0.198 10 false J31 0.25,3.698 0.542,3.896 0.292,0.198 10 false J28 2.5,1.719 2.969,1.979 0.469,0.26 10 false IND 1.99,4.271 2.365,4.427 0.375,0.156 10 false TIRE

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J31-5 (IND) - J28-13 (TIRE) Always Below 1 Ω
J31-5 (IND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR