Home › Drivetrain › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM
RM27M0U _52 Drivetrain _049120 TIRE AND WHEEL _0234088 TIRE PRESSURE WARNING SYSTEM U

TIRE AND WHEEL  TIRE PRESSURE WARNING SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch OFF.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menu items: Chassis / Tire Pressure Monitor / Data List.


e.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mode Status Tire pressure warning system
mode/Normal or Test
Normal: Normal mode
Test: Test mode
-
Main Tire Number of tire IDs to be registered/
4 or 5
4 should be displayed -
Vehicle Speed Vehicle speed reading/
min.: 0 km/h (0 mph),
max.: 255 km/h (158 mph)
Actual vehicle speed Speed indicated on the combination meter
Registered ID1 Code Registered ID1 code/
min.: 0
max.: FFFFFFFF*1
The transmitter ID registered in the transmitter ID1 is displayed -
Registered ID2 Code Registered ID2 code/
min.: 0
max.: FFFFFFFF*1
The transmitter ID registered in the transmitter ID2 is displayed -
Registered ID3 Code Registered ID3 code/
min.: 0
max.: FFFFFFFF*1
The transmitter ID registered in the transmitter ID3 is displayed -
Registered ID4 Code Registered ID4 code/
min.: 0
max.: FFFFFFFF*1
The transmitter ID registered in the transmitter ID4 is displayed -
ID Transmission Status Transmitter ID transmission status /
Finish or Now
Finish or Now -
Initialization Switch Tire pressure warning reset switch/
ON or OFF
ON: Switch is pressed and held
OFF: Switch is not pressed
-
Initialization SW Info Tire pressure warning reset switch setting information/
WITH or WITHOUT
WITH or WITHOUT -
ID 1 Tire Inflation Pressure ID1 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
ID 2 Tire Inflation Pressure ID2 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
ID 3 Tire Inflation Pressure ID3 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
ID 4 Tire Inflation Pressure ID4 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
ID 5 Tire Inflation Pressure - - -
ID 1 Temperature in Tire ID1 temperature in tire/
min.: -50°C (-58°F),
max.: 205°C (401°F)
Actual tire temperature If -50°C (-58°F) is displayed, the data has not been received.
ID 2 Temperature in Tire ID2 temperature in tire/
min.: -50°C (-58°F),
max.: 205°C (401°F)
Actual tire temperature If -50°C (-58°F) is displayed, the data has not been received.
ID 3 Temperature in Tire ID3 temperature in tire/
min.: -50°C (-58°F),
max.: 205°C (401°F)
Actual tire temperature If -50°C (-58°F) is displayed, the data has not been received.
ID 4 Temperature in Tire ID4 temperature in tire/
min.: -50°C (-58°F),
max.: 205°C (401°F)
Actual tire temperature If -50°C (-58°F) is displayed, the data has not been received.
ID 5 Temperature in Tire - - -
ID 1 Battery Voltage ID1 battery voltage/
OVER or LESS
OVER -
ID 2 Battery Voltage ID2 battery voltage/
OVER or LESS
OVER -
ID 3 Battery Voltage ID3 battery voltage/
OVER or LESS
OVER -
ID 4 Battery Voltage ID4 battery voltage/
OVER or LESS
OVER -
ID 5 Battery Voltage - - -
ID 1 Initial Threshold of Low-pressure ID1 initial threshold of low pressure (Absolute pressure) /
min.: 100.00 kPa (1 kgf/cm2, 14 psi)
max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
Tire pressure after initialization -
ID 2 Initial Threshold of Low-pressure ID2 initial threshold of low pressure (Absolute pressure) /
min.: 100.00 kPa (1 kgf/cm2, 14 psi)
max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
Tire pressure after initialization -
ID 3 Initial Threshold of Low-pressure ID3 initial threshold of low pressure (Absolute pressure) /
min.: 100.00 kPa (1 kgf/cm2, 14 psi)
max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
Tire pressure after initialization -
ID 4 Initial Threshold of Low-pressure ID4 initial threshold of low pressure (Absolute pressure) /
min.: 100.00 kPa (1 kgf/cm2, 14 psi)
max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
Tire pressure after initialization -
ID 5 Initial Threshold of Low-pressure - - -
Number of DTC Number of DTCs recorded/
min.: 0
max.: 255
0 -

HINT:
·

*1: Displayed only when the ID No. is not registered.

·

*2: It may take about 5 or 6 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>C2121/21).





PERFORM ACTIVE TEST


HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the tester, perform the "Active Test".

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light ON or OFF Perform the test with the vehicle stopped and engine idling