Home › Drivetrain › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM
RM27M0U _52 Drivetrain _049120 TIRE AND WHEEL _0234088 TIRE PRESSURE WARNING SYSTEM C

TIRE AND WHEEL  TIRE PRESSURE WARNING SYSTEM  C2121/21  No Signal from Transmitter ID1  C2122/22  No Signal from Transmitter ID2  C2123/23  No Signal from Transmitter ID3  C2124/24  No Signal from Transmitter ID4  C2181/81  Transmitter ID1 not Received (Test Mode DTC)  C2182/82  Transmitter ID2 not Received (Test Mode DTC)  C2183/83  Transmitter ID3 not Received (Test Mode DTC)  C2184/84  Transmitter ID4 not Received (Test Mode DTC)  


DESCRIPTION

The tire pressure warning valves and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of the tires. The measured values are transmitted to the tire pressure warning antenna and receiver on the body as radio waves and then sent to the tire pressure warning ECU. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter turns on.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning antenna and receiver.

Under the conditions below, the tire pressure warning antenna and receiver is unable to receive the signals from the tire pressure warning valves and transmitters, and a DTC is stored.

·

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

·

Devices using similar radio frequencies are used in the vehicle.

·

The ID of the tire pressure warning valve and transmitter is mistyped during registration.

·

A tire/wheel/transmitter from a different vehicle is installed.

·

The parts, such as tire chains, window film which obstruct the radio signal of the tire pressure warning valve and transmitter.


HINT:

These DTCs are detected when the vehicle is driven and no signals are received for 20 minutes or more.

DTCs from C2121/21 to C2124/24 can only be cleared by using the tester or receiving the signal from the tire pressure warning valve and transmitter. DTCs from C2181/81 to C2184/84 can be cleared when the transmitter in the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs from C2181/81 to C2184/84 are output only in test mode.


DTC Code DTC Detection Condition Trouble Area
C2121/21
C2122/22
C2123/23
C2124/24
When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode

·

Signal is not received from tire pressure warning valve and transmitter when driving the vehicle at more than 8 km/h (5 mph) for 20 minutes or more


·

Tire pressure warning valve and transmitter

·

Tire pressure warning antenna and receiver

·

Harness or connector

·

Tire pressure warning ECU


C2181/81
C2182/82
C2183/83
C2184/84
Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning antenna and receiver

·

Harness or connector

·

Tire pressure warning ECU



HINT:

It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM

C158876E14
2.042,1.969 4.896,2.458 2.854,0.49 10 false Front Tire Pressure Warning Valve and Transmitter RH 4.021,0.615 4.323,0.802 0.302,0.188 10 false +5V 3.99,0.938 4.365,1.104 0.375,0.167 10 false RDA 3.979,1.313 4.333,1.469 0.354,0.156 10 false GND 0.417,0.563 0.729,0.75 0.313,0.188 10 false P17 0.406,0.729 3.281,0.917 2.875,0.188 10 false Tire Pressure Warning Antenna and Receiver 2.042,2.865 4.896,3.354 2.854,0.49 10 false Front Tire Pressure Warning Valve and Transmitter LH 2.042,3.771 4.896,4.26 2.854,0.49 10 false Rear Tire Pressure Warning Valve and Transmitter RH 2.021,4.646 4.875,5.135 2.854,0.49 10 false Rear Tire Pressure Warning Valve and Transmitter LH 1.292,6.073 1.604,6.271 0.313,0.198 10 false J43 1.281,6.25 3.646,6.479 2.365,0.229 10 false Tire Pressure Warning Reset Switch 1.042,8.229 2.021,8.438 0.979,0.208 10 false : Radio Signal 5.292,7.615 5.563,7.781 0.271,0.167 10 false J31 5.292,7.823 7.063,8.063 1.771,0.24 10 false Tire Pressure Warning ECU 6.031,6.906 6.552,7.167 0.521,0.26 10 false GND 6.021,5.677 6.542,5.875 0.521,0.198 10 false CLSW 5.729,5.552 5.906,5.75 0.177,0.198 10 false 1 5.74,6.781 5.927,6.979 0.188,0.198 10 false 9 6.031,0.594 6.615,0.833 0.583,0.24 10 false RF5V 6.042,0.948 6.771,1.208 0.729,0.26 10 false RDA 6.031,1.313 6.594,1.583 0.563,0.271 10 false GND2 5.719,0.479 5.906,0.677 0.188,0.198 10 false 6 5.667,0.823 5.938,1.01 0.271,0.188 10 false 12 5.667,1.198 5.865,1.396 0.198,0.198 10 false 11 4.49,1.177 4.729,1.375 0.24,0.198 10 false 4 4.49,0.813 4.656,1.01 0.167,0.198 10 false 1 4.49,0.469 4.719,0.625 0.229,0.156 10 false 5 2.271,5.552 2.49,5.75 0.219,0.198 10 false 1 1.156,5.552 1.271,5.802 0.115,0.25 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or the tire pressure warning valve and transmitter has been replaced.



PROCEDURE

1.READ OUTPUT DTC (DTC C2174/74)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC C2174/74 is not output A
DTC C2174/74 is output B

NOTICE:

When DTC C2174/74 is output, troubleshoot that DTC first. Then troubleshoot DTCs C2121/21 to C2124/24.




A

2.CHECK FREQUENCY RECEIVING CONDITION

B

2.CHECK FREQUENCY RECEIVING CONDITION
a.

Check if the vehicle is in conditions such as the ones described below:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in areas described above, the tire pressure warning light may blink for a minute and turn on in a particular area.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio frequency may be interrupted due to the surroundings, or devices installed by the user.





OK

3.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

NG

CHECK IF ANY DEVICE IS INSTALLED BY USER

3.IDENTIFY TRANSMITTER CORRESPONDING TO DTC
a.

Set the tire pressures to the appropriate specified value(s) (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>PRECAUTION).


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and the Techstream on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*

HINT:

*: It may take about 5 to 6 minutes until the values are displayed.



g.

Rapidly reduce the tire pressure for each tire at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.


h.

Check the Data List.

NOTICE:
·

It may take about 5 to 6 minutes to display the updated tire pressure data.

·

When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.

·

Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.




i.

After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID4) has changed, repeat this procedure for the other tires. Identify the transmitter that corresponds to the DTC.

Result
Condition Proceed to
All abnormal A
One or more transmitters are abnormal B
All normal C



A

4.CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)

B

5.CHECK TRANSMITTER ID

C

END

4.CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)
a.

Disconnect the J31 ECU connector.


b.

Disconnect the P17 receiver connector.


c.
U152696E02
1.323,3.948 1.031,4.031 true 1.823,4 1.875,4.396 true 2.063,3.969 2.333,4.073 true 2.135,1.698 2.438,1.698 true 2.115,1.49 2.406,1.323 true 0.271,0.104 2.615,0.469 2.344,0.365 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.292,2.208 2.625,2.729 2.333,0.521 10 false Front view of wire harness connector: (to Tire Pressure Warning Antenna and Receiver) 0.573,1.063 0.958,1.24 0.385,0.177 10 false J31 0.708,3.448 1.021,3.625 0.313,0.177 10 false P17 2.469,1.24 2.854,1.396 0.385,0.156 10 false RF5V 2.479,1.615 2.823,1.813 0.344,0.198 10 false RDA 0.563,1.635 1.01,1.802 0.448,0.167 10 false GND2 2.375,4 2.698,4.208 0.323,0.208 10 false +5V 1.74,4.417 2.073,4.573 0.333,0.156 10 false GND 0.698,3.979 1.021,4.135 0.323,0.156 10 false RDA

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J31-12 (RDA) - P17-1 (RDA) Always Below 1 Ω
J31-11 (GND2) - P17-4 (GND) Always Below 1 Ω
J31-6 (RF5V) - P17-5 (+5V) Always Below 1 Ω
J31-12 (RDA) - Body ground Always 10 kΩ or higher
J31-11 (GND2) - Body ground Always 10 kΩ or higher
J31-6 (RF5V) - Body ground Always 10 kΩ or higher




OK

5.CHECK TRANSMITTER ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TRANSMITTER ID
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
Registered ID1 Code Registered ID1 code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in the transmitter ID1 is displayed *: Displayed only when the transmitter ID is not registered.
Registered ID2 Code Registered ID2 code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in the transmitter ID2 is displayed *: Displayed only when the transmitter ID is not registered.
Registered ID3 Code Registered ID3 code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in the transmitter ID3 is displayed *: Displayed only when the transmitter ID is not registered.
Registered ID4 Code Registered ID4 code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in the transmitter ID4 is displayed *: Displayed only when the transmitter ID is not registered.


f.

Check the transmitter ID on the identified transmitter by removing it from the tire and wheel.

C156141E02
4.656,1.073 5.198,0.698 5.198,0.698 5.521,0.698 false 0.104,0.094 2.99,0.469 2.885,0.375 10 false Tire Pressure Warning Valve and Transmitter: 5.583,0.615 6.573,1.052 0.99,0.438 10 false Transmitter ID (8 Digit Number)


g.

Confirm that the transmitter ID on the transmitter and recorded transmitter ID match.

Result
Result Proceed to
Match A
Do not match B



A

6.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

7.REGISTRATION OF TRANSMITTER ID
6.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the tire pressure warning valve and transmitter (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING VALVE AND TRANSMITTER>REMOVAL).



NEXT

7.REGISTRATION OF TRANSMITTER ID
7.REGISTRATION OF TRANSMITTER ID

NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

NEXT

9.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
9.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*

HINT:
·

*: It may take about 5 to 6 minutes until the values are displayed.

·

When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.



Result
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B



A

10.REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER

B

END

10.REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER
a.

Replace the tire pressure warning antenna and receiver (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

11.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
11.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
Actual tire inflation pressure If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*

HINT:
·

*: It may take about 5 to 6 minutes until the values are displayed.

·

When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.



Result
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B



A

REPLACE TIRE PRESSURE WARNING ECU

B

END