Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM D

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  SYSTEM DESCRIPTION  


DESCRIPTION


·

A part-time 2-speed WF1AM transfer uses a touch select 2-4 and high-low system, enabling the driver to switch between 2WD, 4H and 4L modes by turning the transfer position switch.

·

Through these switch signals, the 4 wheel drive control ECU actuates the shift motor in the transfer shift actuator and another shift motor in the A.D.D. actuator (differential vacuum actuator assembly).



DRIVING MODE SWITCHING PATTERN


C295253E01
0.261,0.109 0.459,0.293 0.198,0.184 10 *1

Text in Illustration
*1 Transfer Position Switch - -


INDICATOR LIGHT AND WARNING BUZZER OPERATING CONDITIONS


Mode 4HI Indicator Light 4LO Indicator Light Warning Buzzer
2WD Not illuminated Not illuminated Not sounding
Switching from 2WD to 4H Blinking Not illuminated Not sounding
2WD to 4L switch request (not permitted) Blinking Not illuminated Sounding
4H Illuminated Not illuminated Not sounding
Switching from 4H to 2WD Blinking Not illuminated Not sounding
Switching from 4H to 4L Illuminated Blinking Not sounding
4H to 4L switch request (not permitted) Illuminated Blinking Sounding
4L Not illuminated Illuminated Not sounding
Switching from 4L to 2WD Blinking Illuminated Not sounding
4L to 2WD switch request (not permitted) Blinking Illuminated Sounding
Switching from 4L to 4H Blinking Illuminated Not sounding
Malfunctioning Rapidly blinking Rapidly blinking Not sounding

·

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



FUNCTION OF COMPONENTS


Components Functions
Transfer position switch Allows switching between the 3 drive modes: 2WD, 4HI and 4LO.
Combination meter assembly 4HI indicator light Illuminates to inform the user of 4HI mode status.
Blinks to inform the user of mode switching.
Rapidly blinks to inform the user of a system malfunction.
4LO indicator light Illuminates to inform the user of 4LO mode status.
Blinks to inform the user of mode switching.
Rapidly blinks to inform the user of a system malfunction.
Warning buzzer Sounds an alarm if a violation of the conditions required for mode shifting occurs when the transfer mode is shifted.
Skid control ECU Outputs wheel speed signals to the 4 wheel drive control ECU via CAN communication.
Speed sensors Detects the speeds of all 4 wheels and sends that information to the skid control ECU.
ECM Outputs information such as the shift lever position and engine speed to the 4 wheel drive control ECU via CAN communication.
Park/neutral position switch Detects the shift lever position and sends that information to the ECM.
4 wheel drive control ECU Determines the vehicle status from wheel and engine speed signals received via CAN communication, and according to the operation of the transfer position switch, switches to the requested 4WD mode by operating the transfer shift actuator assembly.
Transfer shift actuator assembly Operates the transfer shift motor according to commands sent from the 4 wheel drive control ECU and switches to 4WD mode.
Transfer indicator switch Detects the 2WD, 4HI and 4LO positions and sends that information to the 4 wheel drive control ECU.
A.D.D. actuator (differential vacuum actuator assembly) A.D.D. shift motor and limit switch Operates the A.D.D. shift motor according to commands sent from the 4 wheel drive control ECU and switches between 2WD and 4WD.
A.D.D. detection switch Detects the 2WD and 4WD A.D.D. positions and sends that information to the 4 wheel drive control ECU.

·

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)


·

Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)