Home › Drivetrain › WF1AM TRANSFER › TRANSFER ASSEMBLY
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234108 TRANSFER ASSEMBLY G

WF1AM TRANSFER  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 33309B 1.INSPECT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (FRONT)

a.
C291202E01
2.829,0.286 2.985,0.490 0.156,0.205 10 A 1.581,0.269 1.737,0.473 0.156,0.205 10 B

Using a micrometer, measure the outer diameter of the output shaft companion flange sub-assembly (front) journal surface.

Minimum Diameter:
Journal Specified Condition
A 34.962 mm (1.376 in.)
B 39.955 mm (1.573 in.)


If the outer diameter is less than the minimum, replace the output shaft companion flange sub-assembly (front).


Hide 36270 2.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C291203

Using a feeler gauge, measure the thrust clearance of the pinion gear.

Maximum clearance:

0.93 mm (0.037 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


b.
C291204

Using a dial indicator, measure the radial clearance of the pinion gear.

Maximum clearance:

0.021 mm (0.0008 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


Hide 36231 3.INSPECT REAR TRANSFER OUTPUT SHAFT

a.
C291205E01
0.173,0.294 0.304,0.457 0.132,0.163 10 A 0.461,0.289 0.592,0.452 0.132,0.163 10 B 1.294,0.139 1.426,0.302 0.132,0.163 10 C 1.561,0.212 1.692,0.375 0.132,0.163 10 D 2.424,0.251 2.556,0.414 0.132,0.163 10 E

Using a micrometer, measure the diameter of the rear transfer output shaft journal.

Minimum Diameter:
Journal Specified Condition
A 29.987 mm (1.181 in.)
B 34.848 mm (1.372 in.)
C 58.000 mm (2.284 in.)
D 49.110 mm (1.934 in.)
E 44.874 mm (1.767 in.)


If the diameter is less than the minimum, replace the rear transfer output shaft.


Hide 35285B 4.INSPECT SOLENOID LOCK PLATE AND NO. 2 TRANSFER GEAR SHIFT FORK CLEARANCE

a.
C291206E01
0.149,1.377 0.281,1.536 0.132,0.159 10 A 1.885,0.887 2.017,1.046 0.132,0.159 10 B

Using a vernier caliper, measure the thickness of the No. 2 transfer gear shift fork claw.

Standard thickness (A):

6.90 to 7.06 mm (0.272 to 0.277 in.)



b.

Using a vernier caliper, measure the width of the groove of the solenoid lock plate.

Standard width (B):

7.16 to 7.32 mm (0.282 to 0.288 in.)



c.

Calculate the clearance between the solenoid lock plate and No. 2 transfer gear shift fork claw.

Maximum clearance (B) - (A):

0.42 mm (0.017 in.)


If the clearance is more than the maximum, replace the solenoid lock plate or No. 2 transfer gear shift fork.


Hide 36311F 5.INSPECT NO. 1 TRANSFER GEAR SHIFT FORK AND NO. 2 TRANSFER GEAR SHIFT FORK

a.
C291207

Check the gear shift fork pad for wear or damage.

If necessary, replace the gear shift fork pad.


b.
C291209E01
2.57,0.512 2.712,0.682 0.142,0.170 10 A 2.575,2.225 2.717,2.395 0.142,0.170 10 B 0.077,0.048 0.252,0.227 0.174,0.179 10 *1 0.106,1.687 0.280,1.866 0.174,0.179 10 *2

Using a micrometer, measure the outer diameter of the No. 1 transfer gear shift fork and No. 2 transfer gear shift fork.

Minimum Diameter:
Diameter Specified Condition
A 12.586 mm (0.496 in.)
B 12.586 mm (0.496 in.)


Text in Illustration
*1 No. 1 Transfer Gear Shift Fork
*2 No. 2 Transfer Gear Shift Fork

If the diameter is less than the minimum, replace the No. 1 transfer gear shift fork or No. 2 transfer gear shift fork.


Hide 36235 6.INSPECT TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
C291208

Using a vernier caliper, measure the thickness of the transfer high and low clutch sleeve.

Minimum thickness:

3.00 mm (0.1182 in.)


If the thickness is less than the minimum, replace the transfer high and low clutch sleeve.


Hide 36255 7.INSPECT TRANSFER OUTPUT SHAFT SPACER

a.
C291210

Using a vernier caliper, measure the thickness of the No. 1 transfer output shaft spacer and No. 2 transfer output shaft spacer.

Minimum Thickness:
Transfer Output Shaft Spacer Minimum Thickness
No. 1 Transfer Output Shaft Spacer 2.80 mm (0.111 in.)
No. 2 Transfer Output Shaft Spacer 4.045 mm (0.160 in.)


If the thickness is less than the minimum, replace the transfer output shaft spacer.


Hide 44109C 8.INSPECT SOLENOID COIL SUB-ASSEMBLY

a.
C291151E01
1.567,0.904 1.404,1.432 1.404,1.432 0.403,1.432 false 0.171,1.325 0.351,1.505 0.180,0.180 10 *a

Install the solenoid coil sub-assembly with the 3 nuts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

Text in Illustration
*a Rear Transfer Case Hole

Make sure that the solenoid coil sub-assembly terminal extends out from the rear transfer case hole.


b.

Connect the solenoid coil sub-assembly terminal.

i.
C301682

Attach the claw to connect the solenoid coil sub-assembly terminal.


ii.
C301683

Install the retainer to the coupler.



c.

Measure the resistance according to the value(s) in the table below.

C291226E02
1.583,1.604 1.333,2.25 1.333,2.25 1.094,2.25 false 0.927,0.49 1.156,0.688 0.229,0.198 10 false *a 0.75,2.177 1.146,2.375 0.396,0.198 10 false SCC 5.115,0.667 5.302,0.833 0.188,0.167 10 true *b 6.302,1.375 6.531,1.573 0.229,0.198 10 false *b 5.344,2.198 5.573,2.427 0.229,0.229 10 true *b

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SCC) - Case GND Always 1.62 to 1.78 Ω


Text in Illustration
*a Component without harness connected
(Solenoid Coil Sub-assembly)
*b Case GND

HINT:

For case ground, perform the measurement at one of the locations indicated by the arrows.