Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY
RM27M0U _54 Brake _049124 PARKING BRAKE _0234124 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL PARKING BRAKE ANCHOR BLOCK

a.
C155126

Install the anchor block with the 2 nuts.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


Hide 46430 2.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C154244

Connect the No. 3 parking brake cable with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.INSTALL PARKING BRAKE SHOE LEVER LH

a.

Apply high temperature grease to the parking brake shoe lever.


b.
C155125

C117760E04
0.396,0.125 0.948,0.365 0.552,0.24 12 false for LH: 2.031,0.115 2.583,0.365 0.552,0.25 12 false for RH:

Install the parking brake shoe lever to the No. 3 parking brake cable.

NOTICE:

Carefully distinguish the parking brake shoe lever RH and LH.



Hide 46590 4.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Apply high temperature grease to the areas of the backing plate that contact the shoe.


b.
C154249E02
0.729,1.854 0.729,1.615 0.729,1.615 2.021,1.615 false 0.604,1.875 0.896,2.031 0.292,0.156 10 false SST

Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

SST
09718-00011  


Hide 46580 5.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.

Apply high temperature grease to the areas of the backing plate that contact the shoe.


b.
C193371E06
0.75,4.156 2.333,4.333 1.583,0.177 10 false High temperature grease

Apply the high temperature grease to the areas of the shoe adjusting screw set shown in the illustration.


c.

Set the parking brake shoe and shoe adjuster screw set in place.


d.

Connect the tension spring.


e.
C155124E02
2.792,1.302 2.792,1.563 false 2.625,1.583 2.917,1.74 0.292,0.156 10 false SST

Using SST, install the No. 1 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

SST
09718-00011  


Hide 6.INSTALL PARKING BRAKE SHOE RETURN SPRING

a.
C179358E02
2.844,1.271 2.844,1.531 false 2.708,1.542 3.031,1.698 0.323,0.156 10 false SST

Using SST, install the shoe return spring.

SST
09703-30011  


Hide 7.CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C156989E01
0.254,0.189 1.028,0.440 0.774,0.251 12 for LH: 3.636,0.2 4.322,0.452 0.686,0.251 12 for RH: 5.671,2.51 6.054,2.664 0.384,0.154 10 Front 1.302,2.487 1.685,2.640 0.384,0.154 10 Front


Hide 42431 8.INSTALL REAR DISC

Hide 9.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C158344

Connect the rear disc brake cylinder with 2 new bolts.

Torque:
167 N*m (1703 kgf*cm, 123 ft.*lbf)

NOTICE:
·

Do not twist the brake hose.

·

Make sure that the bolts are free from damage and foreign matter.

·

Do not overtighten the bolts.




Hide 10.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 11.CHECK PARKING BRAKE PEDAL TRAVEL

Hide 12.ADJUST PARKING BRAKE PEDAL TRAVEL

Hide 13.INSTALL REAR WHEEL LH

Torque:
for aluminum wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for steel wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 14.SETTLE PARKING BRAKE SHOE AND DISC

a.

Drive the vehicle for approximately 400 m (0.25 miles) under the following conditions.

i.

The vehicle speed is approximately 50 km/h (31 mph) and the vehicle is on a safe, level and dry road.


ii.

The parking brake pedal is being depressed with a force of 150 N (15 kgf, 33.7 lbf).



b.

Repeat the procedures above 2 or 3 times.