Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049125 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0234142 AUTOMATIC TRANSMISSION SYSTEM J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Pattern Select Switch Circuit  


DESCRIPTION

The ECM receives tow/haul pattern select switch information and performs the tow/haul control.

While the tow/haul control is operating, in contrast to normal mode, low gears are used to increase engine braking and towing power, reduce frequent shifts, and improve driveability. The tow/haul control includes throttle control, shift schedule control, wide open throttle shift timing control and AI-SHIFT control.

Tow/haul mode only operates when the shift lever is in the D position and the tow/haul pattern select switch is ON.

HINT:
·

The tow/haul pattern select switch is a momentary-type switch.

·

In order to cancel tow/haul mode, push the tow/haul pattern select switch again or turn the ignition switch off.



WIRING DIAGRAM

C162870E09
0.045,2.99 1.679,3.191 1.634,0.202 10 *1: for Column Shift Type 0.045,3.362 1.679,3.564 1.634,0.202 10 *2: for Floor Shift Type 5.717,2.213 6.086,2.382 0.369,0.170 10 A24 5.717,2.366 6.139,2.561 0.422,0.195 10 ECM 2.372,1.096 2.794,1.292 0.422,0.195 10 J25 2.372,1.271 4.178,1.466 1.806,0.195 10 Transmission Control Switch 2.372,2.401 2.896,2.596 0.524,0.195 10 J23 2.372,2.575 4.636,2.770 2.265,0.195 10 Tow/Haul Pattern Select Switch 3.526,0.604 3.671,0.799 0.144,0.195 10 P 2.91,0.604 3.054,0.799 0.144,0.195 10 E 2.745,0.835 2.931,1.030 0.186,0.195 10 9 3.717,0.835 3.903,1.030 0.186,0.195 10 12 2.745,2.14 2.931,2.335 0.186,0.195 10 1 3.717,2.14 3.903,2.335 0.186,0.195 10 4 4.589,1.861 4.792,2.063 0.204,0.202 10 *2 4.589,0.557 4.792,0.759 0.204,0.202 10 *1 5.219,0.836 5.404,1.031 0.186,0.195 10 51 5.515,0.719 5.919,0.914 0.404,0.195 10 PWR

PROCEDURE

1.INSPECT TOW/HAUL PATTERN SELECT SWITCH ASSEMBLY
a.
C159524E07
0.057,0.006 2.588,0.374 2.531,0.367 10 Component without harness connected: (Transmission Control Switch) 2.763,2.057 2.957,2.258 0.193,0.202 10 E 0.766,2.149 1.589,1.827 false 0.574,2.057 0.735,2.258 0.161,0.202 10 P 2.684,2.149 2.008,1.827 false

for Column Shift Type:

i.

Disconnect the J25 transmission control switch connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
12 (P) - 9 (E) Tow/haul pattern select switch ON Below 1 Ω
12 (P) - 9 (E) Tow/haul pattern select switch OFF 10 kΩ or higher




b.
C162988E01
0.056,0.045 2.587,0.412 2.531,0.367 10 Component without harness connected: (Tow/Haul Pattern Select Switch) 2.264,2.51 2.442,2.655 0.178,0.145 10 1 1.268,2.51 1.432,2.655 0.164,0.145 10 4 1.544,1.836 1.35,2.474 false 2.078,1.836 2.272,2.473 false

for Floor Shift Type:

i.

Disconnect the J23 tow/haul pattern select switch connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
4 - 1 Tow/haul pattern select switch ON Below 1 Ω
4 - 1 Tow/haul pattern select switch OFF 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C




A

2.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - BODY GROUND)

B

REPLACE COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY (TRANSMISSION CONTROL SWITCH)

C

REPLACE TOW/HAUL PATTERN SELECT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - BODY GROUND)
a.
U152213E01
0.386,1.639 0.761,1.872 0.375,0.233 10 J25 0.058,0.004 2.467,0.372 2.409,0.367 10 Front view of wire harness connector: (to Transmission Control Switch) 0.894,2.312 1.38,1.992 false 0.717,2.204 0.887,2.406 0.170,0.202 10 E

for Column Shift Type:

i.

Disconnect the J25 transmission control switch connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J25-9 (E) - Body ground Always Below 1 Ω




b.
U152361E01
0.058,0.005 2.467,0.372 2.409,0.367 10 Front view of wire harness connector: (to Tow/Haul Pattern Select Switch) 1.059,2.536 1.338,1.803 false 0.969,2.551 1.172,2.753 0.203,0.202 10 1 0.403,1.589 0.778,1.822 0.375,0.233 10 J23

for Floor Shift Type:

i.

Disconnect the J23 tow/haul pattern select switch connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J23-1 - Body ground Always Below 1 Ω





OK

3.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - ECM)
a.
U152250E01
0.052,0.006 2.461,0.373 2.409,0.367 10 Front view of wire harness connector: (to ECM) 1.681,1.001 2.056,1.234 0.375,0.233 10 A24 0.869,2.867 1.556,3.069 0.687,0.202 10 51 (PWR) 1.296,2.852 1.605,2.196 false

Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
A24-51 (PWR) - Body ground Tow/haul pattern select switch ON Below 1 Ω
A24-51 (PWR) - Body ground Tow/haul pattern select switch OFF 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR