Home › Vehicle Interior › INTERIOR PANEL › INSTRUMENT PANEL SAFETY PAD(for Floor Shift Type)
RM27M0U _58 Vehicle Interior _049163 INTERIOR PANEL _0234481 INSTRUMENT PANEL SAFETY PAD(for Floor Shift Type) A

INTERIOR PANEL  INSTRUMENT PANEL SAFETY PAD(for Floor Shift Type)  REMOVAL  


PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.


U152091E01
0.664,1.795 0.936,1.977 0.272,0.181 10 <A> 2.639,1.795 2.911,1.977 0.272,0.181 10 <B> 4.639,1.795 4.918,1.977 0.280,0.181 10 <C> 0.66,3.48 0.940,3.661 0.280,0.181 10 <D> 2.639,3.48 2.911,3.661 0.272,0.181 10 <E> 2.069,1.63 2.526,1.812 0.457,0.181 10 (0.236) 2.069,2.032 2.399,2.213 0.330,0.181 10 L=25 2.069,2.387 2.526,2.569 0.457,0.181 10 (0.984) 4.057,3.323 4.386,3.504 0.330,0.181 10 L=15 4.057,3.678 4.514,3.859 0.457,0.181 10 (0.590) 6.007,1.923 6.464,2.104 0.457,0.181 10 (0.236) 0.608,0.875 0.957,1.056 0.349,0.181 10 Code 2.606,0.875 2.955,1.056 0.349,0.181 10 Code 4.577,0.875 4.926,1.056 0.349,0.181 10 Code 1.532,0.875 1.951,1.056 0.419,0.181 10 Shape 3.545,0.875 3.964,1.056 0.419,0.181 10 Shape 5.569,0.875 5.987,1.056 0.419,0.181 10 Shape 4.057,1.63 4.514,1.812 0.457,0.181 10 (0.236) 4.057,2.032 4.386,2.213 0.330,0.181 10 L=20 4.057,2.387 4.514,2.569 0.457,0.181 10 (0.787) 4.057,1.279 4.407,1.472 0.350,0.193 10 φ 6 5.17,0.442 6.545,0.628 1.376,0.186 10 mm (in.) (L = Length) 0.66,5.352 0.965,5.534 0.304,0.181 10 <G> 4.639,3.48 4.911,3.661 0.272,0.181 10 <F> 2.069,3.323 2.399,3.504 0.330,0.181 10 L=21 2.069,3.678 2.526,3.859 0.457,0.181 10 (0.826) 4.057,5.157 4.514,5.338 0.457,0.181 10 (0.236) 4.057,5.559 4.386,5.740 0.330,0.181 10 L=22 4.057,5.914 4.514,6.095 0.457,0.181 10 (0.866) 4.057,4.764 4.407,4.957 0.350,0.193 10 φ 6 2.069,5.157 2.526,5.338 0.457,0.181 10 (0.315) 2.069,5.559 2.399,5.740 0.330,0.181 10 L=20 2.069,5.914 2.526,6.095 0.457,0.181 10 (0.787) 2.069,4.764 2.419,4.957 0.350,0.193 10 φ 8 6.039,3.323 6.369,3.504 0.330,0.181 10 L=20 6.039,3.678 6.496,3.859 0.457,0.181 10 (0.787) 2.634,5.352 2.939,5.534 0.304,0.181 10 <H>

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

a.

Disable the Autoaway/Return function by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).

NOTICE:

Record the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.



b.

Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column.


c.

Turn the ignition switch off.


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 55061 5.REMOVE NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY

Hide 33504F 7.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

a.
B355384

Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.


Hide 58805C 8.REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

a.

Move the shift lever to N.


b.
B355386E01
1.934,2.966 2.126,3.132 0.192,0.166 10 *1 2.127,3.054 2.275,3.054 2.275,3.054 2.35,2.618 false

Apply protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


c.

Using a moulding remover B, detach the 6 clips and remove the upper rear console panel sub-assembly.


Hide 58804A 9.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

a.
B355388

Detach the 12 clips and remove the upper console panel sub-assembly.


Hide 58903A 10.REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY

a.
B355389

Using a moulding remover B, detach the 7 clips and remove the rear console end panel sub-assembly.


b.

w/ Power Outlet Socket:

Detach the 2 wire harness clamps and disconnect the connector.


Hide 58815A 11.REMOVE CONSOLE BOX CARPET

B355391

a.

Remove the console box carpet.


Hide 58910C 12.REMOVE REAR CONSOLE BOX ASSEMBLY

a.
B355392

Disconnect the 2 connectors.


b.

Remove the 2 screws <E> and 4 bolts <B> and rear console box assembly.


Hide 58811A 13.REMOVE FRONT CONSOLE BOX

a.
B355393

Remove the 2 clips and detach the connector.


b.

Remove the 5 screws <E> and front console box.


Hide 67914 14.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913 16.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62111C 17.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 55046A 18.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

Hide 73900 19.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55474C 20.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55447C 21.REMOVE NO. 2 SWITCH HOLE BASE

a.
B355394E01
2.802,2.712 2.989,2.875 0.187,0.163 10 *1 2.791,2.813 2.606,2.813 2.606,2.813 2.517,2.624 false

Apply protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Detach the 4 clips and remove the No. 2 switch hole base.


c.

Disconnect each connector.


Hide 55471A 22.REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT

a.
B355396E01
3.081,1.25 3.278,1.406 0.198,0.156 10 *1 3.059,1.332 2.737,1.332 2.737,1.332 2.622,1.427 false

Apply protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Detach the 3 clips, claw and remove the instrument cluster finish panel ornament.


Hide 55410C 23.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B355398

Remove the 2 clips.


b.

Detach the 6 clips and remove the instrument cluster finish panel assembly.


Hide 83100 24.REMOVE COMBINATION METER ASSEMBLY

Hide 55607 25.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55045A 30.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH

Hide 55475A 31.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 32.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY

Hide 86140A 33.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

Hide 55405B 34.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 62312B 35.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 37.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 55409A 39.REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 55409F 41.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 55301 43.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

a.

for Manual Tilt Steering Column:

Operate the tilt lever to fully extend and lower the steering column.


b.

Disconnect each connector and each wire harness clamp.


c.

for Automatic Air Conditioning System:

Detach the 2 claws and disconnect the cooler thermistor.

B355399E02
2.802,0.615 3.01,0.781 0.208,0.167 10 true *A 3.021,0.938 3.229,1.104 0.208,0.167 10 true *B 1.531,4.573 1.74,4.74 0.208,0.167 10 false *C

Text in Illustration
*A w/ Automatic Light Control System *B w/ Front Center Speaker
*C for Automatic Air Conditioning System - -


d.

Apply protective tape as shown in the illustration.

B355400E02
1.625,1.313 1.375,1.313 1.375,1.313 1.24,1.656 false 1.635,1.24 1.833,1.438 0.198,0.198 10 false *1 5.104,5.458 5.302,5.615 0.198,0.156 10 false *2 5.865,5.438 6.042,5.594 0.177,0.156 10 true *2 6.448,3.146 6.625,3.302 0.177,0.156 10 true *3 4.052,4.51 4.229,4.667 0.177,0.156 10 true *3 3.135,4.51 3.323,4.677 0.188,0.167 10 true *3 2.875,4.792 3.052,4.948 0.177,0.156 10 false *4 1.188,4.906 1.365,5.063 0.177,0.156 10 false *4

Text in Illustration
*1 Protective Tape *2 Bolt <G>
*3 Bolt <B> *4 Nut <C>


e.

Remove the 2 bolts <G>.


f.

Remove the 3 bolts <B> and 2 nuts <C>.


g.

Detach the 5 claws and remove the instrument panel sub-assembly.