Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049126 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0234159 AUTOMATIC TRANSMISSION SYSTEM C

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code DTC Detection Condition Trouble Area
P0724 The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (1.86 mph)) and GO (30 km/h (18.65 mph) or more) pattern 5 times. (2-trip detection logic)
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during "stop and go" driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (1.86 mph)) and go (30 km/h (18.65 mph) or more) 5 times for 2 driving cycles in order to detect a malfunction.

MONITOR STRATEGY

Related DTCs P0724: Stop light switch/Range check/Rationality
Required sensors/Components Stop light switch, Vehicle speed sensor
Frequency of operation Continuous
Duration GO and STOP 5 times
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The stop light switch remains ON during GO and STOP 5 times.

GO and STOP is defined as follows
The monitor will run whenever the following DTCs are not stored None
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF
GO: (Vehicle speed is 30 km/h (18.65 mph) or more) Once
STOP: (Vehicle speed is less than 3 km/h (1.86 mph)) Once

TYPICAL MALFUNCTION THRESHOLDS

Stop light switch status On

WIRING DIAGRAM

C146704E76
5.229,1.469 5.458,1.635 0.229,0.167 10 false 36 3.948,1.469 4.177,1.635 0.229,0.167 10 false 2 4.719,1.469 4.948,1.635 0.229,0.167 10 false 1 2.073,1.542 2.396,1.74 0.323,0.198 10 false ALT 3.01,1.542 3.688,1.74 0.677,0.198 10 false STOP 5.531,1.354 5.958,1.552 0.427,0.198 10 false STP 1.646,2.406 2.177,2.604 0.531,0.198 10 false Battery 3.823,1.708 4.052,1.906 0.229,0.198 10 false A4 3.823,1.885 5.083,2.083 1.26,0.198 10 false Stop Light Switch 5.698,2.885 6.042,3.052 0.344,0.167 10 false A24 5.698,3.042 6.125,3.24 0.427,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Engine and ECT:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
Brake pedal is:
·

Depressed: ON

·

Released: OFF


-



PROCEDURE

1.INSPECT STOP LIGHT SWITCH
a.
C159061E02
1.646,1.292 1.104,0.938 true 2.427,1.885 1.938,1.531 true 1.896,1.292 2.438,0.938 true 1.094,1.885 1.583,1.531 true 0.542,3.208 0.719,2.688 0.719,2.688 0.802,2.688 false 0.958,0.813 1.104,1.01 0.146,0.198 10 false 2 2.479,0.813 2.615,1.01 0.135,0.198 10 false 1 0.979,1.813 1.156,2.01 0.177,0.198 10 false 4 2.469,1.813 2.615,2.01 0.146,0.198 10 false 3 0.854,2.594 1.104,2.813 0.25,0.219 10 false Pin 0.052,3.823 0.583,4.177 0.531,0.354 10 false Not Pushed 0.74,3.823 1.271,4.125 0.531,0.302 10 false Pushed 0.052,0.052 2.615,0.417 2.563,0.365 10 false Component without harness connected: (Stop Light Switch)

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

NG

REPLACE STOP LIGHT SWITCH

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)
a.
U152248E02
2.281,2.896 1.979,2.073 true 0.052,0.052 2.458,0.417 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.677,1.042 2.052,1.271 0.375,0.229 10 false A24 1.969,2.917 2.667,3.115 0.698,0.198 10 false 36 (STP)

Disconnect the A24 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A24-36 (STP) - Body ground Brake pedal is depressed 11 to 14 V
A24-36 (STP) - Body ground Brake pedal is released Below 1 V


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C