The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0751 | S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 2nd. (b) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th. |
·
Shift solenoid valve S1 remains closed ·
Valve body is blocked ·
Automatic transmission (clutch, brake or gear, etc.) |
| P0751 | S1 stuck OFF malfunction*2: The ECM determines there is a malfunction when conditions (a) and (b) are met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th. (b) When the ECM directs the transmission to switch to 6th gear, the engine overruns (clutch slips). |
·
Shift solenoid valve S1 remains open ·
Shift solenoid valve SLT remains open or closed ·
Valve body is blocked ·
No. 2 brake malfunction (Driving is difficult.) ·
Automatic transmission (clutch, brake or gear, etc.) |
Gear positions in the event of a solenoid valve mechanical problem:
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under S1 stuck ON malfunction | 2nd | 2nd | 3rd | 4th | 5th | 6th |
| *2: Actual gear position under S1 stuck OFF malfunction | 1st | 1st | 3rd | 4th | 5th | N* |
N*: Neutral
Gear position during fail-safe operation:
If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.
| Gear position under normal conditions | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under fail-safe mode when S1 stuck ON malfunction | 2nd | 2nd | 3rd | 4th | 5th | 6th |
| *2: Actual gear position under fail-safe mode when S1 stuck OFF malfunction | 1st*3 | 1st*3 | 3rd | 3rd | 3rd | 3rd |
*3: Under engine braking, downshifting to 1st or 2nd gear is prohibited.
This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S1.
The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.
| Related DTCs | P0751: Shift solenoid valve S1/Functional check |
| Required sensors/Components | Shift solenoid valve S1, Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE), Throttle position sensor, MAF |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) and ON malfunction (A), (B)
0.4 seconds OFF malfunction (B) 3 seconds OFF malfunction (C) 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit) P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0979, P0980 (Shift solenoid valve S3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm
(Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off)
7.75% or more (A/C on) |
| Input speed/output speed (NT/NO)
NT: Input (Turbine) speed NO: Internal counter shaft speed |
3.11 to 7.58
or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| Current ECM selected gear | 6th |
| Last ECM selected gear | 5th |
| Vehicle speed (During transition from 5th to 6th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 6th |
| Engine speed-Turbine speed (NE-NT) (After transition from 5th to 6th gear) | 150 rpm or less |
| Vehicle speed (After transition from 5th to 6th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 1st |
| Vehicle speed | 2 km/h (1.2 mph) or more and less than 40 km/h (24.9 mph) |
| Engine speed-Turbine speed (NE-NT) | 50 rpm or more |
| Calculated load value | 7.75% or more (A/C off)
7.75% or more (A/C on) |
| Input speed/output speed (NT/NO)
NT: Input (Turbine) speed NO: Internal counter shaft speed |
3.11 to 7.58
or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm
(Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off)
7.75% or more (A/C on) |
| Input speed/output speed (NT/NO)
NT: Input (Turbine) speed NO: Internal counter shaft speed |
3.11 to 7.58
or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
Both of the following conditions are met: OFF malfunction (A) and OFF malfunction (B) or (C)
| Turbine speed/Output speed (NT/NO) | 0.66 or more, and 0.80 or less
(This means actual gear is 5th) |
| Turbine speed-Output speed x 5th gear ratio
(NT-NO x 5th gear ratio) |
1000 rpm or more |
| Turbine speed-Output speed x 6th gear ratio
(NT-NO x 6th gear ratio) |
1000 rpm or more |
Both of the following conditions are met: ON malfunction (A) and (B)
2 detections are necessary per driving cycle:
1st detection: temporary flag ON
2nd detection: pending fault code ON
| Turbine speed/Output speed (NT/NO) | 1.83 or more, and 2.27 or less
(This means actual gear is 2nd) |
| Turbine speed/Output speed (NT/NO) | 0.66 or more, and 0.80 or less
(This means actual gear is 5th) |
Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
While driving, the shift position can be forcibly changed with the Techstream.
Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate shift solenoid valve and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Possible to check operation of shift solenoid valves
[Vehicle Condition] 50 km/h (30 mph) or less |
This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.
The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the Data List display on the Techstream.
The shift solenoid valve S1 turns ON/OFF normally when the shift lever is in the D position.
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve S1 | OFF | ON | ON | ON | ON | ON |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
|---|---|
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
If any other codes besides P0751 are output, perform troubleshooting for those DTCs first.
A
B
Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
Be careful to prevent SST's hose from interfering with the exhaust pipe.
Perform the test with the A/C OFF.
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Remove the test plug on the transmission case center right side and connect SST.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF
|
[Vehicle Condition]
·
Vehicle stopped ·
Engine idling |
*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.
The line pressure changes as specified when performing the Active Test.
OK
NG
Remove shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.
Valve moves and makes an operating noise.
OK
NG
Check the transmission valve body assembly (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY).
There are no foreign objects on any valve.
OK
(See pageDrivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL)
NG