Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM27M0U _52 Drivetrain _049126 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0234153 AUTOMATIC TRANSMISSION ASSEMBLY A

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 37110 6.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 17410 7.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 8.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C155905

a.

Remove the nut and clip, and disconnect the shift control cable.


Hide 28100 9.REMOVE STARTER ASSEMBLY

Hide 32101A 10.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

A162758

a.

Remove the flywheel housing side cover.


b.
C161354

Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.


Hide 35000 11.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C161355

a.

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


Hide 51204 12.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C161357

a.

Remove the 4 bolts of the rear engine mounting insulator.


b.
C161358

Remove the 4 nuts, 4 washers, 4 bolts and frame crossmember.


Hide 12371 13.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C161359

a.

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 14.DISCONNECT WIRE HARNESS AND CONNECTOR

C155915

a.

Remove the bolt and disconnect the ground cable.


b.
U152337

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



c.
C353007

Disconnect the park/neutral position switch connector, 2 transmission wire connectors and 2 speed sensor connectors.

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



d.

Disconnect the 3 connector clamps and 4 harness clamps.


e.

Remove the 2 bolts and disconnect the harness clamps and wire harness.


Hide 35104V 15.DISCONNECT BREATHER PLUG HOSE

C163095

a.

Disconnect the breather plug hose from the harness clamp bracket.


Hide 16278 16.DISCONNECT NO. 2 WATER BY-PASS PIPE (w/ Trailer Towing System)

C162128

a.

Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then separate the by-pass pipe from the automatic transmission.

NOTICE:

Use a container to catch any coolant which flows out of the water by-pass hoses.



b.
C162139

Disconnect the 2 transmission oil cooler hoses from the transmission oil thermostat.


Hide 16278 17.DISCONNECT NO. 2 WATER BY-PASS PIPE (w/o Trailer Towing System)

a.
C162563

Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then separate the by-pass pipe from the automatic transmission.

NOTICE:

Use a container to catch any coolant which flows out of the water by-pass hoses.



Hide 35000 18.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C161363

Remove the 10 bolts and transmission.

NOTICE:

Do not use excess force to pry off the transmission assembly.



Hide 33490F 19.REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)

C161366

a.

Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.


b.

Separate the oil cooler from the transmission oil thermostat.


c.

Remove the 4 O-rings.


Hide 33490F 20.REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)

C161367

a.

Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.


b.

Separate the transmission oil cooler from the transmission oil cooler spacer.


c.

Remove the 4 O-rings.


Hide 21.REMOVE HARNESS CLAMP BRACKET

a.

Remove the 3 bolts and 3 brackets.


Hide 33823A 22.REMOVE TRANSMISSION CONTROL CABLE BRACKET

C161368

a.

Remove the 2 bolts and bracket.


Hide 32000 23.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.