Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234172 AUTOMATIC TRANSMISSION UNIT G

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  INSPECTION  


PROCEDURE

Hide 35106 1.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D001124

a.

Remove the magnets, and use them to collect steel particles.


b.

Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

·

Steel (magnetic): bearing, gear and clutch plate wear

·

Brass (non-magnetic): bush wear



Hide 35780B 2.INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY

C352748E01
2.375,0.198 2.99,0.396 0.615,0.198 10 false Lock 2.646,0.885 3.26,1.083 0.615,0.198 10 false Free

a.

Hold the reverse clutch hub and turn the 1-way clutch assembly.


b.

Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.

If there is a problem with the 1- way clutch, replace the No. 2 1-way clutch assembly.


Hide 35677C 3.INSPECT REAR CLUTCH DISC

C162758

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35049 4.INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

D028000

a.

Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

Standard inside diameter:

35.812 to 35.837 mm (1.410 to 1.411 in.)


Maximum inside diameter:

35.887 mm (1.413 in.)


If the inside diameter is more than the maximum, replace the reverse clutch hub.



Hide 35061 5.INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
D028501

Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

Standard inside diameter:

26.037 to 26. 062 mm (1.025 to 1.026 in.)


Maximum inside diameter:

26.112 mm (1.028 in.)


If the inside diameter is more than the maximum, replace the forward clutch hub.



Hide 34360B 6.INSPECT UNDERDRIVE 1-WAY CLUTCH ASSEMBLY

C161784E01
0.137,0.814 0.520,0.989 0.383,0.175 10 Lock 1.624,0.07 1.966,0.273 0.342,0.202 10 Free

a.

Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.

If there is a problem with the 1-way clutch, replace the underdrive 1-way clutch assembly.


Hide 35633B 7.INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

C161790

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35685 8.INSPECT COAST CLUTCH DISC

C161789

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35603A 9.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C161788

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

26.74 mm (1.05 in.)


If the free length is less than the standard, replace the forward clutch return spring sub-assembly.


Hide 35667A 10.INSPECT DIRECT CLUTCH DISC

C161787

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35047 11.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

C161786

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.04 mm (0.828 in.)


If the free length is less than the standard, replace the reverse clutch return spring sub-assembly.


Hide 35604 12.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C161785

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

19.51 mm (0.768 in.)


If the free length is less than the standard, replace the direct clutch return spring sub-assembly.


Hide 13.INSPECT NO. 3 BRAKE DISC

C161778

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35046 14.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C171518

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

15.72 mm (0.619 in.)


If the free length is less than the standard, replace the No. 3 brake piston return spring sub-assembly.


Hide 35720 15.INSPECT FRONT PLANETARY GEAR ASSEMBLY

D028544

a.

Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

Standard clearance:

0.2 to 0.60 mm (0.00787 to 0.0236 in.)


Maximum clearance:

0.65 mm (0.0256 in.)


If the clearance is more than the maximum, replace the front planetary gear assembly.



b.
D028543

Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

Maximum inside diameter:

57.48 mm (2.26 in.)


If the inside diameter is more than the maximum, replace the front planetary gear.



Hide 35790 16.INSPECT 1-WAY CLUTCH ASSEMBLY

C352749E01
1.073,0.115 1.688,0.313 0.615,0.198 10 false Free 2.156,0.26 2.771,0.458 0.615,0.198 10 false Lock

a.

Install the 1-way clutch to the 1-way clutch inner race.


b.

Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

If there is a problem with the 1-way clutch, replace the 1-way clutch assembly.


c.

Remove the 1-way clutch from the 1-way clutch inner race.


Hide 35681A 17.INSPECT NO. 1 BRAKE DISC

C171514

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35608J 18.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C171519

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.05 mm (0.671 in.)


If the free length is less than the standard, replace the brake piston return spring sub-assembly.


Hide 35682A 19.INSPECT NO. 2 BRAKE DISC

a.
C161770

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35045 20.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C171520

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.45 mm (0.687 in.)


If the free length is less than the standard, replace the No. 2 brake piston return spring sub-assembly.


Hide 35750 21.INSPECT CENTER PLANETARY GEAR ASSEMBLY

a.
D028533

Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

Standard clearance:

0.12 to 0.68 mm (0.00472 to 0.0268 in.)


Maximum clearance:

0.73 mm (0.0287 in.)


If the clearance is more than the maximum, replace the center planetary gear assembly.



Hide 35770C 22.INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

C352750E01
0.656,0.302 1.271,0.5 0.615,0.198 10 false Lock 0.344,1.25 0.958,1.448 0.615,0.198 10 false Free

a.

Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

If there is a problem with the 1-way clutch, replace the No. 3 1-way clutch assembly.


Hide 35077D 23.INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

a.
D028531

Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.

Maximum inside diameter:

32.175 mm (1.27 in.)


If the inside diameter is more than the maximum, replace the rear planetary ring gear.



Hide 35713 24.INSPECT INTERMEDIATE SHAFT

a.
D028529

Using a dial indicator, measure the intermediate shaft runout.

Maximum runout:

0.08 mm (0.00315 in.)


If the runout is more than the maximum, replace the intermediate shaft with a new one.


b.
C352751E01
0.698,2.958 0.854,3.156 0.156,0.198 10 false A 1.396,2.948 1.552,3.146 0.156,0.198 10 false B 1.948,2.948 2.104,3.146 0.156,0.198 10 false C 2.271,2.958 2.427,3.156 0.156,0.198 10 false D

Using a micrometer, check the outer diameter of the intermediate shaft at the positions shown in the diagram.

Standard diameter:
A, B:

25.962 to 25.975 mm (1.022 to 1.023 in.)

C, D:

32.062 to 32.075 mm (1.262 to 1.263 in.)


Minimum diameter:
A, B:

25.912 mm (1.02 in.)

C, D:

32.012 mm (1.26 in.)


If the outer diameter is less than the minimum, replace the intermediate shaft with a new one.


Hide 35684 25.INSPECT NO. 4 BRAKE DISC

a.
C161745

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.



Hide 35760 26.INSPECT REAR PLANETARY GEAR ASSEMBLY

C161743

a.

Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

Standard clearance:

0.2 to 0.6 mm (0.00787 to 0.0236 in.)


Maximum clearance:

0.65 mm (0.0256 in.)


If the clearance is more than the maximum, replace the planetary gear assembly.



b.
D028528

Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

Maximum inside diameter:

20.075 mm (0.790 in.)


If the inside diameter is more than the maximum, replace the rear planetary gear assembly.



Hide 35068 27.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C171521

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

23.74 mm (0.935 in.)


If the free length is less than the standard, replace the 1st and reverse brake return spring sub-assembly.


Hide 28.INSPECT INDIVIDUAL PISTON OPERATION

a.
U116395E03
0.781,0.948 0.365,0.448 true 1.031,0.781 1.188,0.302 true 1.271,0.792 1.479,0.313 true 2.698,1.01 3.094,1.01 true 1.792,2.26 3.052,2.26 true 1.802,2.688 3.042,2.688 true 1.802,3.083 3.063,3.083 true 1.646,4.031 1.396,4.396 true 1.896,4.031 2.135,4.365 true 0.177,0.271 0.552,0.5 0.375,0.229 10 false C2 1.125,0.073 1.479,0.281 0.354,0.208 10 false C4 1.469,0.125 1.823,0.385 0.354,0.26 10 false C1 3.125,0.927 3.396,1.156 0.271,0.229 10 false C3 3.104,2.177 3.354,2.448 0.25,0.271 10 false B3 3.073,2.604 3.354,2.833 0.281,0.229 10 false B1 3.104,2.979 3.354,3.26 0.25,0.281 10 false B2 1.969,4.396 2.729,4.667 0.76,0.271 10 false B4 (OUT) 1.167,4.417 1.76,4.667 0.594,0.25 10 false B4 (IN)

Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

HINT:

When inspecting the rear clutch, check the operating sound with the C3 accumulator piston hole closed.

If there is no sound, disassemble and check the installation condition of the parts.


1.

Forward multiple disc clutch (C1)

2.

Direct clutch (C2)

3.

Rear clutch (C3)

4.

Coast clutch (C4)

5.

No. 1 brake (B1)

6.

No. 2 brake (B2)

7.

No. 3 brake (B3)

8.

No. 4 brake (B4)