Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION FLUID
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234174 AUTOMATIC TRANSMISSION FLUID N

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

C351953E01
5.885,2.344 5.885,2.146 5.885,2.146 5.229,1.969 true 2.385,2.542 2.385,2.344 2.385,2.344 1.813,2.063 true 0.167,0.073 2.24,0.292 2.073,0.219 12 false Fluid Filling Procedure: 0.188,0.427 1.854,0.844 1.667,0.417 12 false TRANSMISSION FILL (When necessary) 0.094,0.99 2.927,1.208 2.833,0.219 10 false Add fluid to the oil pan to the specified level. 0.281,2.25 1.448,2.771 1.167,0.521 10 false Add fluid until fluid comes out of the overflow plug hole. 1.844,2.583 3.094,2.948 1.25,0.365 10 false No. 1 Transmission Oil Filler Tube 4.031,0.74 6.479,1.104 2.448,0.365 10 false Add the correct amount of fluid specified for the operation that was performed. 6.271,1.594 6.865,2.125 0.594,0.531 10 false Specified Amount of Fluid 5.552,2.385 6.448,2.615 0.896,0.229 10 false Overflow Plug 1.802,3.26 4.542,3.49 2.74,0.229 12 false FLUID TEMPERATURE CHECK 1.781,3.604 7.125,3.938 5.344,0.333 10 false Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified value. 0.563,5.125 2.406,5.354 1.844,0.229 12 false FLUID LEVEL CHECK 0.563,5.552 2.958,5.875 2.396,0.323 10 false Drain excess fluid at the specified fluid temperature. 0.104,6.99 2.135,7.333 2.031,0.344 10 false Keep the overflow plug open until only drops of fluid come out. 4.365,5.406 6.802,5.771 2.438,0.365 10 false If no fluid comes out, add fluid until fluid comes out of the overflow plug hole.

NOTICE:
·

This transmission requires Toyota Genuine ATF WS.

·

After servicing the transmission, you must follow the ATF adjustment procedure.

·

Maintain the vehicle in a horizontal position while adjusting the fluid level.



PROCEDURE

Hide 1. BEFORE FILLING TRANSMISSION

·

When you have replaced the entire transmission, transmission pan, drain plug, valve body and/or torque converter, proceed to the "Transmission Fill" procedures.

·

When you have replaced the transmission hose and/or output shaft oil seal, proceed to the "Fluid Temperature Check" procedures.


Hide 2. TRANSMISSION FILL

C209344E02
1.833,0.927 1.427,0.115 1.427,0.115 1.333,0.115 true 3.146,1.563 3.073,1.99 3.073,1.99 2.969,1.99 false 2.25,3.729 1.771,4.281 1.771,4.281 1.667,4.281 true 0.688,0.031 1.375,0.219 0.688,0.188 10 false Refill Hole 2.313,1.896 3.021,2.115 0.708,0.219 10 false Refill Plug 0.771,4.198 1.781,4.417 1.01,0.219 10 false Overflow Plug

a.

Remove the refill plug and overflow plug.


b.
C351951E01
2.51,1.115 1.802,0.802 true 0.823,1.188 1.031,0.781 true 2.188,1.146 3.167,1.344 0.979,0.198 10 false Overflow Tube 0.188,1.229 1.552,1.417 1.365,0.188 10 false Specified Fluid Level

Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.


c.

Reinstall the overflow plug.


d.

Fill the transmission with the amount of fluid listed in the table below.

Reference Capacity:
Repair Fill Amount
Transmission pan and drain plug removal 2.1 liters (2.2 US qts, 1.8 Imp. qts)
Transmission valve body removal 4.7 liters (5.0 US qts, 4.1 Imp. qts)
Torque converter removal 5.4 liters (5.7 US qts, 4.8 Imp. qts)



e.

Install the refill plug.

HINT:

If you cannot fill the listed amount of fluid, perform the following:


i.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



ii.

Move the shift lever through the entire gear range to circulate the fluid.


iii.

Wait for 30 seconds with the engine idling.


iv.

Stop the engine.


v.

Remove the refill plug.


vi.

Fill the transmission with the remaining fluid until the amount in the table has been filled.


vii.

Install the refill plug.



Hide 3. FLUID TEMPERATURE CHECK

NOTICE:

The ATF temperature can be confirmed by using the Techstream.


a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Powertrain / ECT / Data List / A/T Oil Temperature 1.


e.

Check the ATF temperature.

NOTICE:

If the ATF temperature is higher than 59°C (138°F), turn the ignition switch off and wait until the fluid temperature drops to between 53 and 59°C (127 and 138°F).



Hide 4. FLUID LEVEL CHECK

NOTICE:
·

It is necessary to change to temperature detection mode in order to idle the vehicle appropriately.

·

The ATF temperature must be between 53 and 59°C (127 and 138°F) to accurately check the fluid level.



a.

When using the Techstream:

Enter the following menus: Powertrain / ECT / Active Test / Connect the TC and TE1.

Standard condition:

Indicator lights in the combination meter blink.



b.
H102392E90
2.039,0.34 2.272,0.490 0.234,0.150 10 CG 2.165,1.765 2.379,1.925 0.214,0.160 10 TC 0.108,0.052 1.437,0.289 1.329,0.237 10 Front view of DLC3: 2.022,0.49 1.616,0.891 false 1.777,1.451 2.123,1.798 false

When not using the Techstream:

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Standard condition:

Indicator lights in the combination meter blink.



c.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



d.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then return the shift lever to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.



e.
C290567E01
0.297,0.091 0.460,0.273 0.164,0.181 10 *A 0.297,2.403 0.460,2.584 0.164,0.181 10 *B

Move the shift lever to D, and quickly move it back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

Text in Illustration
*A w/ Multi-Information Display
*B w/o Multi-Information Display

Standard condition:

Indicator light [D] remains illuminated for 2 seconds and then turns off.



f.

When using the Techstream:

Return the shift lever to P and terminate the Active Test on the Techstream.


g.

When not using the Techstream:

Return the shift lever to P and disconnect SST from the DLC3.


h.

Allow the engine to idle until the fluid temperature reaches 53 to 59°C (127 to 138°F).

HINT:

The indicator [D] will come on again when the fluid temperature reaches 53°C (127°F) and will blink if it is higher than 59°C (138°F).


Indicator [D] Indication of ATF Temperature
Below 53°C (127°F) 53 to 59°C (127 to 138°F) Higher than 59°C (138°F)
Turn off Turn on Blinking


i.
C351951E01
2.51,1.115 1.802,0.802 true 0.823,1.188 1.031,0.781 true 2.188,1.146 3.167,1.344 0.979,0.198 10 false Overflow Tube 0.188,1.229 1.552,1.417 1.365,0.188 10 false Specified Fluid Level

Remove the overflow plug and gasket with the engine idling.


j.

Wait until the overflow slows to a trickle.

NOTICE:

If the fluid does not overflow, perform the following:


i.

Remove the refill plug and gasket.


ii.

Refill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.


iii.

Wait until the overflow slows to a trickle.


iv.

Install a new gasket and the refill plug.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)



k.

Install a new gasket and the overflow plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 5. COMPLETE

a.

Turn the ignition switch off.


b.

When using the Techstream:

Disconnect the Techstream from the DLC3.


c.

Inspect for automatic transmission fluid leaks.


Hide 6. ATF THERMAL DEGRADATION ESTIMATE RESET

HINT:

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).