Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234192 AUTOMATIC TRANSMISSION SYSTEM C

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0894  Transmission Component Slipping  P2714  Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)  


DESCRIPTION

C221301E01
4.885,2.063 5.208,1.125 5.208,1.125 5.271,1.125 true 5.031,2.208 5.188,2.573 5.188,2.573 5.26,2.573 true 5.875,2.271 6,2.573 6,2.573 6.063,2.573 true 6.115,2.479 7,2.698 0.885,0.219 10 false Solenoid Coil 0.104,0.677 1.354,0.896 1.25,0.219 10 false Hydraulic Pressure 2.563,3.01 3.125,3.229 0.563,0.219 10 false Current 5.313,2.49 5.844,2.708 0.531,0.219 10 false Sleeve 5.323,1.031 6.167,1.25 0.844,0.219 10 false Spool Valve

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve.

Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC Code DTC Detection Condition Trouble Area
P0894 The ECM detects a malfunction in shift solenoid valve SLT, S1, S2, S3, S4 or SL2, or the 1-2 shift valve, or an incorrect gear 6 ratio according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2-trip detection logic).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed

·

Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)


P2714 The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2-trip detection logic).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed

·

Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)



MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The ECM illuminates the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.

There are two causes of speed difference.

·

When the shift solenoid valve SLT remains ON, oil pressure decreases, which causes the clutch engagement force to decrease.

·

When a shift solenoid valve remains ON or OFF, the gear position commanded by the ECM and the actual gear position are not the same.


NOTICE:

If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


MONITOR STRATEGY

Related DTCs P0894: Automatic transmission slip malfunction
P2714: Shift solenoid valve SLT/Functional check
Required sensors/Components Shift solenoid valve SLT
Frequency of operation Continuous
Duration P0894 ON malfunction (A): Immediately
P0894 ON malfunction (B): 0.4 seconds
P2714: Immediately
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0717 (Turbine speed sensor circuit)
P0712, P0713 (ATF temperature sensor circuit)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit)
P0500 (Vehicle speed sensor circuit)
ECT (Engine Coolant Temperature) sensor circuit Not circuit malfunction
ETCS (Electric Throttle Control System) Not system down
Transmission position "D"
Duration time from shifting "N" to "D" 4 seconds or more
ECT 40°C (104°F) or higher
Spark advance from max. retard timing by KCS control 0° crankshaft angle or more
Engine Starting

TYPICAL MALFUNCTION THRESHOLDS

[P0894: ON malfunction]

When either condition below is met: ON malfunction (A) or (B)


ON Malfunction (A)
Summation of C1 clutch heat generations Specified value

ON Malfunction (B)
Summation of C2 clutch heat generations Specified value
Actual gear for SLT failure judgment Not determined

[P2714: ON malfunction]

One of the following conditions is met: ON malfunction (A), (B), (C), (D), (E), (F), (G) or (H)


ON Malfunction (A)
Summation of C1 clutch heat generations Specified value

ON Malfunction (B)
Shift solenoid valve S1 OFF malfunction Detected

ON Malfunction (C)
Shift solenoid valve S2 OFF malfunction Detected

ON Malfunction (D)
Shift solenoid valve S3 ON malfunction Detected

ON Malfunction (E)
Shift solenoid valve S4 OFF malfunction Detected

ON Malfunction (F)
1-2 shift valve malfunction Detected

ON Malfunction (G)
Reverse sequence valve malfunction Detected

ON Malfunction (H)
Shift solenoid valve SL2 ON malfunction Detected

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0894 AND P2714)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the Techstream.

Result
Result Proceed to
·

Only P0894 is output

·

Only P0894 and P2714 are output


A
P0894, P2714 and other DTCs are output B

HINT:

If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)

NG

17.INSPECT SHIFT SOLENOID VALVE SLT
3.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)
HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the Techstream to the DLC3.



c.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


d.

According to the display on the Techstream, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the Techstream.


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

·

The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the Techstream.




e.

Compare the ECM gear shift command and the actual gear position.

Result
ECM Gear Shift Command 1st 2nd 3rd 4th 5th 6th Proceed to
Actual gear position under malfunction Shift solenoid S1 Stuck ON*1 2nd 2nd 3rd 4th 5th 6th A
Stuck OFF 1st 1st 3rd 4th 5th N*2
Shift solenoid S2 Stuck ON 1st 2nd 2nd 4th 6th 6th B
Stuck OFF 3rd 3rd 3rd 4th 5th 5th
Shift solenoid S3 Stuck ON 1st 2nd 3rd 3rd N*2 N*2 C
Stuck OFF 3rd 4th 4th 4th 5th 6th
Shift solenoid S4 Stuck ON*3 1st 2nd 3rd 4th 5th 6th D
Stuck OFF 1st 2nd 3rd 4th 4th 4th
Actual gear position when normal 1st 2nd 3rd 4th 5th 6th E

HINT:
·

*1: When shift solenoid S1 is stuck ON, the vehicle cannot drive in reverse.

·

*2: Neutral

·

*3: When shift solenoid S4 is stuck ON, gear shifting is normal.





A

4.INSPECT SHIFT SOLENOID VALVE S1

B

7.INSPECT SHIFT SOLENOID VALVE S2

C

10.INSPECT SHIFT SOLENOID VALVE S3

D

13.INSPECT SHIFT SOLENOID VALVE S4

E

20.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE S1

OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

6.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

6.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

7.INSPECT SHIFT SOLENOID VALVE S2

OK

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

9.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

9.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

10.INSPECT SHIFT SOLENOID VALVE S3

OK

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

12.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

12.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

13.INSPECT SHIFT SOLENOID VALVE S4

OK

14.INSPECT SHIFT SOLENOID VALVE SL2

NG

14.INSPECT SHIFT SOLENOID VALVE SL2

OK

15.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

15.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

16.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

16.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

17.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928E18
1.76,0.99 2.208,0.365 true 1.5,0.99 1.052,0.365 true 1.76,2.948 2.208,2.354 true 1.51,2.948 1.052,2.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.125,4.125 0.198,0.198 10 false (-) 1.115,3.927 1.333,4.125 0.219,0.198 10 false (+)

Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLT)


OK

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

19.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

19.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

20.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928E18
1.76,0.99 2.208,0.365 true 1.5,0.99 1.052,0.365 true 1.76,2.948 2.208,2.354 true 1.51,2.948 1.052,2.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.125,4.125 0.198,0.198 10 false (-) 1.115,3.927 1.333,4.125 0.219,0.198 10 false (+)

Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLT)


OK

21.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

21.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

22.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

22.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG