Home › Steering › POWER STEERING › POWER STEERING SYSTEM(for 1UR-FE)
RM27M0U _55 Steering _049130 POWER STEERING _0234201 POWER STEERING SYSTEM(for 1UR-FE) G

POWER STEERING  POWER STEERING SYSTEM(for 1UR-FE)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVE BELT

a.
C125842E02
0.202,3.698 0.910,3.848 0.708,0.150 10 CORRECT 2.363,3.698 3.215,3.848 0.852,0.150 10 INCORRECT 1.194,3.698 2.046,3.848 0.852,0.150 10 INCORRECT

Visually check the belt for excessive wear, frayed cords, etc.

If any defect is found, replace the drive belt.

HINT:
·

Cracks on the rib side of a belt are considered acceptable. Replace the belt if there are any missing ribs.

·

After installing a belt, check that it fits properly in the ribbed grooves.

·

Check with your hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley.




Hide 2.BLEED POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.


f.

Run the engine at idle for a few minutes.


g.

Turn the steering wheel.

i.

With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, and then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1


ii.

Repeat *1 several times.



h.

Stop the engine.


i.
C124274E02
0.574,0.312 1.303,0.462 0.730,0.150 10 CORRECT 1.919,0.312 2.841,0.462 0.922,0.150 10 INCORRECT

Check for foaming or emulsification.

If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.


j.

Check the fluid level.


Hide 3.CHECK FLUID LEVEL

a.
C158723E01
0.111,0.719 0.582,1.079 0.471,0.360 10 COLD Range 2.794,0.726 3.283,1.093 0.489,0.367 10 HOT Range

Keep the vehicle horizontal.


b.

With the engine stopped, check the fluid level in the reservoir.

If necessary, add fluid.

Fluid:

ATF DEXRON II or III, or equivalent


HINT:

If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.



c.

Start the engine and run it at idle.


d.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



e.
C124274E02
0.574,0.312 1.303,0.462 0.730,0.150 10 CORRECT 1.919,0.312 2.841,0.462 0.922,0.150 10 INCORRECT

Check for foaming or emulsification.

If foaming or emulsification is identified, bleed the power steering system.


f.
U152120E01
0.48,1.589 1.302,1.739 0.822,0.150 10 Engine idling 1.123,0.062 2.095,0.223 0.973,0.162 10 5.0 mm or less 1.909,1.589 2.928,1.739 1.019,0.150 10 Engine stopped 1.437,0.986 1.835,0.986 false 1.591,0.909 2.006,0.909 false 1.718,0.808 1.718,0.545 false 1.726,1.092 1.726,1.355 false

With the engine idling, measure the fluid level in the reservoir.


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the reservoir.

Maximum fluid level rise:

5.0 mm (0.197 in.)


If the fluid level rise is more than the maximum, bleed the power steering system.


i.

Check the fluid level.


Hide 4.CHECK STEERING FLUID PRESSURE

a.

Disconnect the pressure feed tube from the vane pump (See page Steering>POWER STEERING>VANE PUMP(for 1UR-FE)>REMOVAL).


b.

Connect SST as shown in the illustration.

SST
09640-10010  (09641-01010, 09641-01030, 09641-01060)

NOTICE:

Check that the valve of SST is in the open position.



c.

Bleed the power steering system.


d.

Start the engine and run it at idle.


e.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)


C161566E03
5.396,0.188 5.677,0.188 false 5.458,3.094 5.188,3.094 false 1.323,2.854 1.323,3.021 false 2.438,2.25 2.438,3.031 false 4.583,1.635 4.802,1.802 0.219,0.167 10 false IN 6.156,1.635 6.542,1.802 0.385,0.167 10 false OUT 5.729,0.115 6.063,0.292 0.333,0.177 10 false SST 0.979,3.052 1.771,3.229 0.792,0.177 10 false Attachment 5.5,3.01 6.292,3.188 0.792,0.177 10 false Attachment 1.906,3.063 3.198,3.26 1.292,0.198 10 false Pressure Feed Tube


f.
C353064E01
2.344,0.229 3.25,0.427 0.906,0.198 10 false Oil Reservoir 2.385,1.25 3.156,1.458 0.771,0.208 10 false Vane Pump 0.156,0.771 0.719,0.958 0.563,0.188 10 false PS Gear 1.01,0.844 1.469,1.031 0.458,0.188 10 false Closed 1.375,1.656 1.719,1.833 0.344,0.177 10 false SST

With the engine idling, close the valve of SST and observe the reading on SST.

Minimum fluid pressure:

8336 kPa (85.0 kgf/cm2, 1209 psi)


NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is less than the minimum, check for fluid leaks and replace parts as necessary.


g.
C353065E01
2.396,0.229 3.208,0.438 0.813,0.208 10 false Oil Reservoir 2.417,1.229 3.167,1.448 0.75,0.219 10 false Vane Pump 0.146,0.75 0.74,0.927 0.594,0.177 10 false PS Gear 1.125,0.844 1.542,1.021 0.417,0.177 10 false Open 1.427,1.667 1.75,1.844 0.323,0.177 10 false SST

With the engine idling, fully open the valve.


h.

Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

Difference in fluid pressure:

490 kPa (5.0 kgf/cm2, 71 psi) or less


NOTICE:

Do not turn the steering wheel.


If the pressure difference is above the specified range, check for fluid leaks and replace parts as necessary.


i.
C353066E01
0.885,0.438 1.802,0.677 0.917,0.24 10 false Lock Position 1.042,0.781 1.448,0.99 0.406,0.208 10 false Open 2.313,0.167 3.229,0.344 0.917,0.177 10 false Oil Reservoir 2.354,1.198 3.271,1.375 0.917,0.177 10 false Vane Pump 0.167,0.74 0.76,0.906 0.594,0.167 10 false PS Gear 1.333,1.604 1.74,1.813 0.406,0.208 10 false SST

With the engine idling and the valve fully open, turn the steering wheel left or right to the full lock position. Observe the reading on SST.

Minimum fluid pressure:

8336 kPa (85.0 kgf/cm2, 1209 psi)


NOTICE:
·

Do not keep the steering wheel in the full lock position for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is less than the minimum, check for fluid leaks and replace parts as necessary.


j.

Disconnect SST.

SST
09640-10010  (09641-01010, 09641-01030, 09641-01060)


k.

Connect the pressure feed tube (See page Steering>POWER STEERING>VANE PUMP(for 1UR-FE)>INSTALLATION).


l.

Bleed the power steering system.