Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM L

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  PRECAUTION  


CAUTION:
·

The vehicle is equipped with a Supplemental Restraint System (SRS), which consists of a steering pad, front passenger airbag, knee airbag, curtain shield airbag, front seat side airbag, seat belt pretensioner, center airbag sensor, front airbag sensor, side airbag sensor, door side airbag sensor, occupant classification ECU and seat position airbag sensor. Failure to carry out service procedures in the correct sequence could cause SRS parts to unexpectedly deploy and possibly lead to serious injuries. Furthermore, if a mistake is made when servicing SRS parts, they may fail to operate when required. Before performing servicing (including installation/removal, inspection and replacement of parts), be sure to read the following precautions.

·

Before starting work, wait at least 90 seconds after the ignition switch is turned off and after the cable of the negative (-) battery terminal is disconnected. (SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal, SRS parts may deploy.)

·

Do not expose SRS parts directly to hot air or flames.

·

Be sure to perform the initialization of the occupant classification ECU if any of the following conditions occur. If the initialization is not performed, the SRS may not operate properly.

1.

The occupant classification ECU is replaced.

2.

Accessories (seatback tray, seat cover, etc.) are installed onto the vehicle.

3.

The passenger seat is removed from the vehicle, and then reinstalled or replaced.

4.

The passenger airbag ON/OFF indicator light (OFF) comes on when the passenger seat is not occupied.

5.

The vehicle is brought to the workshop for repair due to an accident or collision.




NOTICE:
·

Malfunction symptoms of SRS parts are difficult to confirm. DTCs are the most important source of information when troubleshooting. During troubleshooting, always confirm DTCs before disconnecting the cable from the negative (-) battery terminal.

·

For minor collisions where SRS parts do not deploy, always inspect the SRS parts.

·

Before performing repairs, remove airbag sensors if any kind of impact is likely to occur to an airbag sensor during repairs.

·

Never use SRS parts from another vehicle. When replacing SRS parts, replace them with new ones.

·

Never disassemble or attempt to repair SRS parts.

·

If an SRS part has been dropped, or if there are any cracks, dents or other defects in the case, bracket or connector, replace the SRS part with a new one.

·

Use an ohmmeter/voltmeter with high impedance (10 kΩ/V minimum) for troubleshooting the electrical circuits.

·

Information labels are attached to the periphery of SRS parts. Follow the cautions and instructions on the labels.

·

After work on the SRS is completed, perform the SRS warning light check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).

·

When the cable is disconnected from the negative (-) battery terminal, the memory settings of each system will be cleared. Because of this, be sure to write down the settings of each system before starting work. When work is finished, reset the settings of each system as before. Never use a backup power supply from outside the vehicle to avoid erasing the memory in a system.

·

If the vehicle is equipped with a mobile communication system, refer to the precaution in the INTRODUCTION section.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

In the airbag system, the center airbag sensor, front airbag sensor LH and RH, side airbag sensor LH and RH, door side airbag sensor LH and RH are collectively referred to as the airbag sensors.


HANDLING PRECAUTIONS FOR AIRBAG SENSORS


a.

Before starting the following operations, wait for at least 90 seconds after disconnecting the negative (-) terminal cable from the battery:

i.

Replacement of the airbag sensors.


ii.

Adjustment of the front doors of the vehicle equipped with side airbags and curtain shield airbags (fitting adjustment).



b.

When connecting or disconnecting the airbag sensor connectors, ensure that each sensor is installed in the vehicle.


c.

Do not use airbag sensors which have been dropped during operation or transportation.


d.

Do not disassemble the airbag sensors.



INSPECTION PROCEDURE FOR VEHICLE INVOLVED IN ACCIDENT


a.

When the airbag has not deployed, confirm the DTCs by checking the SRS warning light. If there is any malfunction in the SRS airbag system, perform troubleshooting.


b.

When any of the airbags have deployed due to the collision, be sure to replace all sensors in the damaged areas and center airbag sensor assembly.



SRS CONNECTORS


a.

SRS connectors are located as shown in the following illustration.

E285813E02
0.385,0.188 1.938,0.531 1.552,0.344 10 false Passenger Airbag ON/OFF Indicator 0.385,1.052 1.979,1.25 1.594,0.198 10 false Front Airbag Sensor LH 0.385,1.813 2.469,2.042 2.083,0.229 10 false Steering Pad (Driver Side Squib) 0.385,3.458 2.271,3.823 1.885,0.365 10 false Front Passenger Airbag (Front Passenger Side Squib) 0.396,5.115 1.969,5.313 1.573,0.198 10 false Front Airbag Sensor RH 0.385,5.906 1.74,6.26 1.354,0.354 10 false Combination Meter (SRS Warning Light) 3.479,1.865 4.313,2.063 0.833,0.198 10 false Spiral Cable 4.844,6.979 6.25,7.219 1.406,0.24 10 false Center Airbag Sensor 5.563,3.865 6.594,4.083 1.031,0.219 10 false to Other Side 2.875,0.031 3.063,0.198 0.188,0.167 10 false 5 3.052,0.49 3.219,0.646 0.167,0.156 10 false 6 2.865,0.833 3.052,1.021 0.188,0.188 10 false 7 3.052,1.302 3.177,1.5 0.125,0.198 10 false 8 3.583,1.104 3.833,1.271 0.25,0.167 10 false 19 3.99,1.292 4.229,1.438 0.24,0.146 10 false 20 2.875,1.677 2.969,1.854 0.094,0.177 10 false 9 3.052,2.104 3.313,2.323 0.26,0.219 10 false 10 4.333,1.677 4.563,1.875 0.229,0.198 10 false 22 4.5,1.917 4.74,2.083 0.24,0.167 10 false 21 2.854,3.292 3.073,3.458 0.219,0.167 10 false 11 3.052,3.76 3.333,3.917 0.281,0.156 10 false 12 3.583,3.531 3.823,3.719 0.24,0.188 10 false 24 4,3.771 4.208,3.927 0.208,0.156 10 false 23 0.385,4.271 2.656,4.635 2.271,0.365 10 false Front Passenger Side Knee Airbag (Front Passenger Side Knee Squib) 2.854,4.125 3.073,4.292 0.219,0.167 10 false 15 3.052,4.573 3.333,4.729 0.281,0.156 10 false 16 0.385,2.625 2.313,2.99 1.927,0.365 10 false Driver Side Knee Airbag (Driver Side Knee Squib) 2.854,2.479 3.073,2.646 0.219,0.167 10 false 41 3.052,2.958 3.333,3.115 0.281,0.156 10 false 42 3.583,5.177 3.833,5.344 0.25,0.167 10 false 19 4.01,5.354 4.25,5.5 0.24,0.146 10 false 20 3.052,5.375 3.198,5.594 0.146,0.219 10 false 8 2.896,4.927 3.042,5.125 0.146,0.198 10 false 7 3.052,6.24 3.313,6.406 0.26,0.167 10 false 17 2.865,5.75 3.104,5.958 0.24,0.208 10 false 18 4.865,6.438 5.021,6.625 0.156,0.188 10 false 1 4.875,6.302 4.969,6.448 0.094,0.146 10 false 2 5.667,6.438 5.781,6.594 0.115,0.156 10 false 3 6.26,6.438 6.375,6.594 0.115,0.156 10 false 3 5.656,6.302 5.771,6.458 0.115,0.156 10 false 4 6.26,6.292 6.375,6.448 0.115,0.156 10 false 4

C158068E05
4.146,4.031 6.063,4.438 1.917,0.406 10 false Front Seat Outer Belt LH (Front Pretensioner Squib LH) 0.813,6.938 2.219,7.177 1.406,0.24 10 false Center Airbag Sensor 0.354,4.115 1.385,4.333 1.031,0.219 10 false to Other Side 4.146,0.49 5.854,0.885 1.708,0.396 10 false Curtain Shield Airbag LH (Curtain Shield Squib LH) 4.146,1.688 5.927,1.885 1.781,0.198 10 false Seat Position Airbag Sensor 4.146,2.854 5.781,3.052 1.635,0.198 10 false Front Seat Inner Belt LH 4.146,5.229 5.813,5.594 1.667,0.365 10 false Front Seat Side Airbag LH (Side Squib LH) 4.146,6.406 5.698,6.656 1.552,0.25 10 false Side Airbag Sensor LH 4.146,7.573 6.01,7.823 1.865,0.25 10 false Door Side Airbag Sensor LH* 0.115,8.469 1.979,8.719 1.865,0.25 10 false *: except Regular Cab 3.781,0.365 3.979,0.563 0.198,0.198 10 false 28 3.583,0.792 3.792,0.969 0.208,0.177 10 false 27 3.563,1.771 3.792,1.938 0.229,0.167 10 false 29 3.781,1.552 3.969,1.75 0.188,0.198 10 false 30 3.552,2.969 3.74,3.125 0.188,0.156 10 false 31 3.781,2.698 4,2.885 0.219,0.188 10 false 32 3.563,4.156 3.771,4.302 0.208,0.146 10 false 33 3.781,3.917 3.99,4.063 0.208,0.146 10 false 34 3.573,5.323 3.771,5.49 0.198,0.167 10 false 35 3.781,5.073 3.99,5.24 0.208,0.167 10 false 36 3.552,6.448 3.771,6.615 0.219,0.167 10 false 37 3.792,6.25 3.979,6.417 0.188,0.167 10 false 38 3.781,7.458 4.01,7.604 0.229,0.146 10 false 40 3.563,7.854 3.76,8.01 0.198,0.156 10 false 39 3.573,6.792 3.76,6.958 0.188,0.167 10 false 22 3.083,7.365 3.292,7.531 0.208,0.167 10 false 21 0.76,6.469 0.906,6.615 0.146,0.146 10 false 1 0.771,6.292 0.938,6.448 0.167,0.156 10 false 2 1.594,6.469 1.688,6.656 0.094,0.188 10 false 3 1.594,6.302 1.75,6.49 0.156,0.188 10 false 4 2.354,6.458 2.448,6.646 0.094,0.188 10 false 3 2.344,6.302 2.5,6.49 0.156,0.188 10 false 4

C158069E05
0.708,6.75 2.188,6.979 1.479,0.229 10 false Center Airbag Sensor 0.167,8.396 2.594,8.625 2.427,0.229 10 false *: except Regular Cab 3.979,0.281 5.656,0.688 1.677,0.406 10 false Curtain Shield Airbag RH (Curtain Shield Squib RH) 3.979,1.573 5.667,1.948 1.688,0.375 10 false Front Seat Side Airbag RH (Side Squib RH) 3.979,2.813 5.531,3.021 1.552,0.208 10 false Side Airbag Sensor RH 3.979,4.063 5.854,4.292 1.875,0.229 10 false Door Side Airbag Sensor RH* 3.979,5.323 5.938,5.677 1.958,0.354 10 false Front Seat Outer Belt RH (Front Pretensioner Squib RH) 3.979,6.604 5.813,6.802 1.833,0.198 10 false Occupant Classification ECU 3.438,0.385 3.667,0.563 0.229,0.177 10 false 27 3.625,0.135 3.823,0.344 0.198,0.208 10 false 28 3.427,1.646 3.625,1.813 0.198,0.167 10 false 35 3.635,1.406 3.833,1.583 0.198,0.177 10 false 36 3.438,3.156 3.656,3.313 0.219,0.156 10 false 37 3.625,2.646 3.823,2.844 0.198,0.198 10 false 38 3.24,3.49 3.479,3.688 0.24,0.198 10 false 22 2.813,3.823 3.052,3.979 0.24,0.156 10 false 21 3.646,3.917 3.854,4.094 0.208,0.177 10 false 40 3.448,4.354 3.677,4.542 0.229,0.188 10 false 39 3.448,5.594 3.688,5.792 0.24,0.198 10 false 33 3.635,5.156 3.854,5.344 0.219,0.188 10 false 34 3.448,6.885 3.646,7.042 0.198,0.156 10 false 41 3.625,6.406 3.865,6.604 0.24,0.198 10 false 42 0.688,6.375 0.833,6.542 0.146,0.167 10 false 1 1.51,6.385 1.635,6.573 0.125,0.188 10 false 3 2.25,6.375 2.375,6.563 0.125,0.188 10 false 3 1.51,6.219 1.635,6.427 0.125,0.208 10 false 4 2.25,6.208 2.375,6.417 0.125,0.208 10 false 4 0.688,6.208 0.802,6.365 0.115,0.156 10 false 2 0.729,4.646 1.677,4.802 0.948,0.156 10 false to Other Side

No. Item Application
(1) Terminal Twin-Lock Mechanism Connectors 2, 4, 8, 10, 12, 21, 22, 23, 25, 26, 27, 29, 31, 33, 35, 37, 39
(2) Activation Prevention Mechanism Connectors 2, 4, 24, 26, 36
(3) Half Connection Prevention Mechanism Connectors 21, 23, 25, 36
(4) Connector Position Assurance Mechanism Connectors 8, 37, 39
(5) Connector Lock Mechanism (1) Connectors 10, 12, 16, 27, 33, 35
(6) Connector Lock Mechanism (2) Connectors 2, 4
(7) Improper Connection Prevention Lock Mechanism Connectors 1, 3


b.
Z005953E25
1.021,0.521 1.563,0.698 1.563,0.698 2.344,0.385 false 1.042,1.198 1.427,1.323 1.427,1.323 1.969,1.156 false 1.323,0.667 1.792,0.865 0.469,0.198 10 false Spacer 1.135,1.313 1.667,1.51 0.531,0.198 10 false Housing 2.198,1.771 2.521,1.969 0.323,0.198 10 false Male 0.292,1.771 0.792,1.969 0.5,0.198 10 false Female

All connectors in the SRS, except the seat position airbag sensor connector, are colored yellow to distinguish them from other connectors. These connectors have special functions, and are specially designed for the SRS. All SRS connectors use durable gold-plated terminals, and are placed in the locations shown below to ensure high reliability.

i.

Terminal twin-lock mechanism:

All connectors with a terminal twin-lock mechanism have a two-piece component consisting of a housing and a spacer. This design enables the terminal to be locked securely by two locking devices (the retainer and the lance) to prevent terminals from coming out.


ii.

Activation prevention mechanism:

All connectors with an activation prevention mechanism contain a short spring plate. When these connectors are disconnected, the short spring plate creates a short circuit by automatically connecting the positive (+) and negative (-) terminals of the squib.

C353029E01
5.406,2.719 5.917,2.031 5.917,2.031 5.5,1.333 false 1.708,2.667 2.24,1.99 2.24,1.99 1.938,1.333 false 1.104,2.76 0.885,2.292 false 2.198,3.26 1.979,3.021 false 2.031,4.448 1.469,3.979 false 1.25,3.844 0.979,3.26 0.979,3.26 1.375,3.844 false 1.177,4.104 1.323,4.365 1.323,4.365 1.354,4.146 false 5.281,2.823 5.344,2.271 5.344,2.271 5.198,2.271 false 4.969,3.792 5.031,3.24 5.031,3.24 4.885,3.24 false 5.323,4.365 5.323,4.01 false 1,0.031 1.156,0.229 0.156,0.198 10 false ● 4.563,0.021 4.719,0.219 0.156,0.198 10 false ● 1.198,0.042 3.125,0.281 1.927,0.24 10 false When Connector is Connected 4.729,0.042 6.896,0.281 2.167,0.24 10 false When Connector is Disconnected 2.323,1.917 5.073,2.115 2.75,0.198 10 false Short Spring Plate 5.958,1.969 7.156,2.25 1.198,0.281 10 false Short Spring Plate 0.354,2.188 1.427,2.385 1.073,0.198 10 false Housing 2.24,3.188 3.313,3.385 1.073,0.198 10 false Housing 2.073,4.365 5.438,4.563 3.365,0.198 10 false Short Spring Plate OFF 0.427,3.177 1.656,3.375 1.229,0.198 10 false Terminal 0.958,4.406 2.49,4.604 1.531,0.198 10 false Connectors 3.594,2.177 5.177,2.417 1.583,0.24 10 false Contacting Male Terminal 3.521,3.167 6.729,3.365 3.208,0.198 10 false Short Spring Plate ON 4.896,4.396 7.042,4.594 2.146,0.198 10 false Closed Circuit 2.042,3.521 2.813,3.719 0.771,0.198 10 false Squib 5.594,3.469 6.365,3.667 0.771,0.198 10 false Squib


iii.

Half connection prevention mechanism:

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.

C150151E15
0.948,0.698 1.115,0.698 1.115,0.698 1.438,1.135 false 1.188,0.333 1.313,0.333 1.313,0.333 1.708,1.031 false 2.281,0.188 2.396,0.188 2.396,0.188 2.344,1.021 false 2.917,0.521 3.052,0.521 3.052,0.521 3.063,0.854 false 3.302,0.188 3.417,0.188 3.417,0.188 3.406,0.979 false 5.969,0.302 5.896,0.302 5.896,0.302 5.917,0.885 false 0.104,0.615 1.052,0.813 0.948,0.198 10 false Locking Part 0.656,0.208 1.271,0.406 0.615,0.198 10 false Stopper 1.458,0.083 2.448,0.281 0.99,0.198 10 false Locking Arm 2.51,0.417 2.979,0.615 0.469,0.198 10 false Slider 2.865,0.094 3.375,0.292 0.51,0.198 10 false Spring 3.646,0.594 5.385,0.792 1.74,0.198 10 false Rebound by Slider (Spring) 6.01,0.198 6.646,0.396 0.635,0.198 10 false Stopper


iv.

Connector position assurance mechanism:

Only when the housing lock (white part) is completely engaged, the CPA (yellow part) slides, which completes the connector engagement.

H043306E13
2.542,0.75 2.25,0.219 2.25,0.219 2.167,0.219 false 2.167,1.458 1.969,1.458 false 0.51,0.115 2.156,0.313 1.646,0.198 10 false Housing Lock (White Part) 0.781,1.354 1.938,1.552 1.156,0.198 10 true CPA (Yellow Part)


v.

Connector lock mechanism (1):

Locking the connector lock button connects the connector securely.

H040181E12
2.177,0.781 1.656,0.781 false 2.135,1.281 1.667,1.281 false 2.688,0.375 3.125,0.375 false 3.135,0.292 3.917,0.49 0.781,0.198 10 false Lock Button 1.323,0.698 1.667,0.896 0.344,0.198 10 false Claw 1.177,1.177 1.667,1.375 0.49,0.198 10 false Groove


vi.

Connector lock mechanism (2):

Both the primary lock with holder lances and the secondary lock with retainer prevent the connectors from becoming disconnected.

C353030E01
1.01,1.865 1.229,1.469 true 1.354,3.542 1.76,3.188 true 3.958,3.094 4.156,2.802 true 5.813,2.76 5.479,2.594 true 4.833,1.646 4.448,1.469 true 0.74,1.865 1.51,2.063 0.771,0.198 10 false Lance 0.813,3.448 2.042,3.646 1.229,0.198 10 false Retainer 3.615,3.094 4.156,3.302 0.542,0.208 10 false Retainer 5.906,2.156 6.448,2.365 0.542,0.208 10 false Retainer 5.063,2.5 5.604,2.708 0.542,0.208 10 false Holder 4.875,1.583 5.417,1.792 0.542,0.208 10 false Holder


vii.

Improper connection prevention lock mechanism:

When connecting the holder, the lever is pushed into the lock position by rotating around the A axis to lock the holder securely.

C160272E12
1.635,1.865 1.865,2.042 0.229,0.177 3.385,2.052 3.615,2.229 0.229,0.177 1.24,1.115 1.24,0.719 1.24,0.719 1.375,0.719 false 5.365,0.865 4.896,0.302 4.896,0.302 4.729,0.302 true 5.323,1.427 4.563,1.427 true 1.458,0.646 1.74,0.948 0.281,0.302 10 false A 1.708,1.875 1.99,2.177 0.281,0.302 10 false 1 3.458,2.063 3.74,2.365 0.281,0.302 10 false 2 4.573,0.229 4.854,0.531 0.281,0.302 10 false A 4.208,1.333 4.719,1.677 0.51,0.344 10 false Lever




DISCONNECTION OF CONNECTORS FOR STEERING PAD, FRONT PASSENGER AIRBAG (SQUIB SIDE), KNEE AIRBAG, CURTAIN SHIELD AIRBAG, FRONT SEAT SIDE AIRBAG AND FRONT SEAT OUTER BELT


HINT:

Tape the screwdriver tip before use.


a.

Release the lock button (yellow part) of the connector using a screwdriver.


b.

Insert the screwdriver tip between the connector and the base, and then raise the connector.

C123672E19
1.49,0.865 1.844,0.323 false 5.417,0.771 5.625,0.344 false 1.406,1.063 1.406,2.156 false 1.677,1.198 2.021,0.906 false 1.875,0.156 2.875,0.563 1,0.406 10 false Lock Button (Yellow Part) 5.667,0.229 6.667,0.635 1,0.406 10 false Lock Button (Yellow Part) 1.219,2.229 1.583,2.417 0.365,0.188 10 false Mark 2.021,0.802 2.375,1 0.354,0.198 10 false Tape



CONNECTION OF CONNECTORS FOR STEERING PAD, FRONT PASSENGER AIRBAG (SQUIB SIDE), KNEE AIRBAG, CURTAIN SHIELD AIRBAG, FRONT SEAT SIDE AIRBAG AND FRONT SEAT OUTER BELT


a.

Connect the connector.


b.

Push down securely on the lock button (yellow part) of the connector. (When locked, a click sound can be heard.)

H043151E25
4.365,1.167 4.844,0.646 false 4.865,0.542 5.833,0.906 0.969,0.365 10 false Lock Button (Yellow Part)



DISCONNECTION OF CONNECTOR FOR SPIRAL CABLE (INSTRUMENT PANEL WIRE SIDE) AND FRONT PASSENGER AIRBAG (INSTRUMENT PANEL WIRE SIDE)


a.

Place a finger on the slider, slide the slider to release the lock, and then disconnect the connector.

C353031E01
0.854,0.813 1.021,0.813 1.021,0.813 1.24,1.25 false 2.885,0.781 3.052,0.781 3.052,0.781 3.271,1.219 false 0.448,0.698 1.365,0.896 0.917,0.198 10 false Slider 2.5,0.688 3.417,0.885 0.917,0.198 10 false Slider 4.625,2.323 6.375,2.521 1.75,0.198 10 false Disconnection is completed



CONNECTION OF CONNECTOR FOR SPIRAL CABLE (INSTRUMENT PANEL WIRE SIDE) AND FRONT PASSENGER AIRBAG (INSTRUMENT PANEL WIRE SIDE)


a.

Connect the connector as shown in the illustration. (When locking, make sure that the slider returns to its original position and a click sound can be heard.)

HINT:

When connecting, the slider will slide. Be sure not to touch the slider while connecting, as it may result in an insecure fit.


H043731E16
2.417,0.542 2.125,0.26 2.125,0.26 1.917,0.26 false 5.833,0.802 5.542,0.521 5.542,0.521 5.323,0.521 false 1.521,0.146 1.927,0.344 0.406,0.198 10 false Slider 4.833,2.177 6.385,2.385 1.552,0.208 10 false Connection is completed 4.927,0.417 5.333,0.615 0.406,0.198 10 false Slider



DISCONNECTION OF CONNECTORS FOR FRONT SEAT SIDE AIRBAG


a.

Place a finger on the slider, slide the slider to release the lock, and then disconnect the connector.

C353032E01
1.063,0.802 1.802,1.323 false 2.948,0.76 3.479,1.302 false 2.552,0.688 3.469,0.885 0.917,0.198 10 false Slider 0.656,0.708 1.573,0.906 0.917,0.198 10 false Slider 4.646,2.167 6.396,2.365 1.75,0.198 10 false Disconnection is completed



CONNECTION OF CONNECTORS FOR FRONT SEAT SIDE AIRBAG


a.

Connect the connector as shown in the illustration. (When locking, make sure that the slider returns to its original position and a click sound can be heard.)

HINT:

When connecting, the slider will slide. Be sure not to touch the slider while connecting, as it may result in an insecure fit.


H043169E11
2.573,0.729 2.313,0.438 2.313,0.438 2.083,0.438 false 5.729,0.969 5.469,0.677 5.469,0.677 5.24,0.677 false 1.677,0.333 2.073,0.531 0.396,0.198 10 false Slider 4.833,0.573 5.229,0.771 0.396,0.198 10 false Slider 4.75,2.135 6.302,2.333 1.552,0.198 10 false Connection is completed



DISCONNECTION OF CONNECTOR FOR CENTER AIRBAG SENSOR


a.

Pull the lever by pushing part A as shown in the illustration and disconnect the holder (with connectors).

H100822E13
1.135,1.573 1.427,1.281 false 5.354,1.49 4.854,0.677 false 1.469,1.177 1.625,1.354 0.156,0.177 10 false A 3.302,0.594 4.823,0.771 1.521,0.177 10 false Holder (with connectors) 4.438,2.438 6.146,2.615 1.708,0.177 10 false Disconnection is complete

HINT:

Perform the following procedures when replacing the holder.



b.

Remove the holder.

i.

Using a screwdriver, unlock the retainer.

H100823E02
2.471,1.005 3.147,1.187 0.676,0.181 10 Retainer 2.179,1.479 2.428,1.089 false


ii.

Release the fitting lance and remove the holder.

H100824E02
1.425,2.136 1.890,2.317 0.465,0.181 10 Lances 1.405,1.821 1.609,2.136 1.609,2.136 0.981,1.821 false 2.133,1.825 1.615,2.144 false



c.
H100825E01
2.657,1.566 3.271,1.740 0.614,0.174 10 Retainer 3.191,1.119 2.987,1.575 false

Install the holder.

i.

Install the connectors to the holder. (When locked, a click sound can be heard.)

HINT:

The retainer is locked when the holder is connected.





CONNECTION OF CONNECTOR FOR CENTER AIRBAG SENSOR


a.

Firmly insert the holder (with connectors) into the center airbag sensor until it cannot be pushed any further.


b.

Push the lever to connect the holder (with connectors). (When locked, a click sound can be heard.)

HINT:

The holder slides into the center airbag sensor when it is being connected. Be sure not to hold the holder while connecting, as it may result in an insecure fit.


H100903E02
1.217,0.323 2.739,0.504 1.522,0.181 10 Holder (with connectors) 4.286,1.066 4.653,1.247 0.366,0.181 10 Lever 5.364,2.24 6.902,2.421 1.538,0.181 10 Connection is complete 3.717,1.5 4.232,1.149 false 0.815,1.257 1.171,0.407 false



DISCONNECTION OF CONNECTOR FOR FRONT AIRBAG SENSOR AND DOOR SIDE AIRBAG SENSOR


a.

Push down the housing lock (white part) and slide the CPA (yellow part). (At this time, the connector cannot be disconnected yet.)


b.

Push down the housing lock (white part) again and disconnect the connector.

HINT:

Do not push down the A part shown in the illustration when disconnecting.


C353033E01
0.938,2.344 1.802,1.063 1.802,1.063 1.938,1.063 false 3.708,1.708 3.708,1.177 false 5.188,0.896 4.281,0.896 false 4.594,0.323 4.021,0.573 false 2.01,0.979 2.958,1.396 0.948,0.417 10 false Connector lock is released 3.146,1.74 5.75,1.938 2.604,0.198 10 false CPA (Yellow Part) 5.24,0.813 6.906,1.021 1.667,0.208 10 false Housing Lock (White Part) 4.667,0.208 4.823,0.406 0.156,0.198 10 false A


c.

After disconnecting the connector, check that the position of the housing lock (white part) is as shown in the illustration.

H043303



CONNECTION OF CONNECTOR FOR FRONT AIRBAG SENSOR AND DOOR SIDE AIRBAG SENSOR


a.

Before connecting the connectors, check that the position of the housing lock (white part) is as shown in the illustration.

H043304


b.

Be sure to engage the connectors until they are locked. (When locking, make sure that a click sound can be heard.)

HINT:

When connecting them, the housing lock (white part) slides. Be sure not to hold the housing lock (white part) and part A, as it may result in an insecure fit.


C353034E01
2.375,1.01 2.708,0.479 2.708,0.479 2.854,0.479 false 2.156,0.781 2.49,0.25 2.49,0.25 2.635,0.25 false 2.417,1.656 2.417,1.396 false 2.896,0.385 4.594,0.625 1.698,0.24 10 false Housing Lock (White Part) 2.677,0.167 2.833,0.365 0.156,0.198 10 false A 1.833,1.688 4.438,1.885 2.604,0.198 10 false CPA (Yellow Part) 5.167,3.375 6.729,3.615 1.563,0.24 10 false Connection is completed



DISCONNECTION OF CONNECTORS FOR SIDE AIRBAG SENSOR


a.
H100826E07
1.708,0.396 1.427,0.115 1.427,0.115 1.25,0.115 false 0.177,0.031 1.229,0.365 1.052,0.333 10 false Outer Connector Locking Sleeve

While holding the sides of the outer connector locking sleeve, slide the sleeve in the direction shown by the arrow.


b.

When the connector lock is released, the connectors are disconnected.

HINT:

Be sure to hold both sides of the sleeve. Holding the top and bottom will make disconnection difficult.


H100827E12
2.688,0.667 2.292,0.188 false 0.583,0.115 2.24,0.292 1.656,0.177 10 false Connector lock is released 4.531,1.323 6.24,1.5 1.708,0.177 10 false Disconnection is complete



CONNECTION OF CONNECTORS FOR SIDE AIRBAG SENSOR


a.

Connect the connector as shown in the illustration (When locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).

HINT:

When connecting, the sleeve will slide. Be sure not to hold the sleeve while connecting, as it may result in an insecure fit.


H100828E16
3.875,0.448 3.875,0.104 3.875,0.104 3.708,0.104 false 6.104,0.365 6.104,0.083 6.104,0.083 6.052,0.083 false 4.542,2.5 6,2.677 1.458,0.177 10 false Connection is complete 4.073,0.021 6.167,0.167 2.094,0.146 10 false Outer Connector Locking Sleeve 1.729,0.021 3.76,0.167 2.031,0.146 10 false Outer Connector Locking Sleeve