Home › General › INTRODUCTION › REPAIR INSTRUCTION
RM27M0U _V1 General _049090 INTRODUCTION _0233743 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED / RECONNECTED



Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal
Necessary Procedure Effect or Inoperative Function when Necessary Procedure is not Performed See page
Gain acquisition mode and trailer brake type setting Initial value Gain value is set to 5.0 (initial value) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED



PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part Necessary Procedures Effects / Inoperative Functions When Necessary Procedures are not Performed See Page
for 1UR-FE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Initialization Engine control system (Click here)
for 3UR-FE, 3UR-FBE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from air induction system

·

Gas leaks from exhaust system

·

Knock sensor


Initialization Engine control system (Click here)(for 3UR-FE)
(Click here)(for 3UR-FBE)
ECM Register VIN DTC P0630 is output (Click here)(for 1UR-FE)
(Click here)(for 3UR-FE)
(Click here)(for 3UR-FBE)
for 3UR-FBE:
Fuel with different alcohol concentration is used
Reset fuel density learning value
·

Engine starting

·

Rough idling


(Click here)
·

Automatic transmission assembly

·

Valve body assembly

·

Any of the shift solenoid valves


Reset memory Large shift shock (Click here)(for AB60F)
(Click here)(for AB60E)
(Click here)(for A760F)
(Click here)(for A760E)
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
Tire pressure warning ECU
1.

Register transmitter IDs

2.

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates

·

Tire pressure monitoring function


(Click here)(for Registration)
(Click here)(for Initialization)
Tire pressure warning valve and transmitter
1.

Register transmitter IDs

2.

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates

·

Tire pressure monitoring function of replaced wheel


Skid control ECU
·

Deceleration sensor zero point calibration

·

Master cylinder pressure sensor zero point calibration


·

ABS warning light illumination

·

Slip indicator light illumination


(Click here)
Yaw rate sensor
·

Zero point calibration data clearance

·

Deceleration sensor zero point calibration


·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC control is prohibited or operation is incorrect


Front Wheel Alignment Adjustment
·

Zero point calibration data clearance

·

Deceleration sensor zero point calibration

·

Perform initialization of steering angle sensor


·

ABS warning light illumination

·

Slip indicator light illumination


Brake Control with Bracket Relay Gain value setting Initial value Gain value is set to 5.0 (initial value) (Click here)
Occupant classification ECU
·

Zero point calibration

·

Sensitivity check


·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger side)


(Click here)
·

Transponder key ECU

·

ECM

·

Key


Registration Engine starting (Click here)
·

Door control transmitter

·

Door control receiver


Register recognition code Wireless door lock operation (Click here)
·

Power window regulator motor (Driver side)

·

Power window regulator motor (Passenger side)


Initialize the motor
·

Jam Protection Function

·

Power window control system (w/ Jam protection function)


(Click here)
Inner rear view mirror Register transmitter code Garage door opener system (Click here)
Compass calibration Direction is not displayed correctly (Click here)
·

Sliding roof drive gear (Sliding roof ECU)

·

Sliding roof housing

·

Sliding roof glass


Initialize sliding roof system
·

Auto operation

·

Jam protection function

·

Sliding roof operation after ignition switch is turned OFF

·

Key-linked operation function (Driver side door only)


(Click here)