Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from OFF to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.

WIRING DIAGRAM

C159525E19
0.782,6.405 2.762,6.581 1.980,0.177 10 CAN Communication Line 2.908,2.559 3.161,2.764 0.253,0.205 10 2 2.915,3.155 3.127,3.324 0.211,0.170 10 1 2.915,3.736 3.148,3.927 0.232,0.191 10 24 3.16,2.657 3.455,2.841 0.295,0.184 10 IG+ 3.16,3.26 3.469,3.457 0.309,0.198 10 B 3.16,3.834 3.490,4.039 0.330,0.205 10 ES 3.637,2.069 4.070,2.211 0.434,0.142 10 CANL 3.63,2.664 4.063,2.827 0.434,0.163 10 CANH 6.177,2.055 6.611,2.197 0.434,0.142 10 CANL 6.177,2.65 6.611,2.813 0.434,0.163 10 CANH 4.126,1.903 4.393,2.073 0.267,0.170 10 40 4.126,2.505 4.351,2.682 0.225,0.177 10 39 4.786,2.905 5.469,3.082 0.684,0.177 10 CAN Line 5.9,1.903 6.160,2.094 0.260,0.191 10 22 5.9,2.505 6.139,2.689 0.239,0.184 10 13 5.893,3.561 6.104,3.765 0.211,0.205 10 25 5.9,4.153 6.125,4.344 0.225,0.191 10 26 6.177,3.659 6.389,3.815 0.211,0.156 10 E1 6.177,4.261 6.417,4.431 0.239,0.170 10 E2 5.907,0.757 6.086,0.908 0.179,0.151 10 21 6.177,0.848 6.528,1.008 0.350,0.161 10 IG2 2.964,5.613 3.266,5.776 0.302,0.163 10 J28 2.964,5.789 4.204,5.972 1.239,0.184 10 Combination Meter 5.794,5.589 6.131,5.751 0.336,0.163 10 J46 5.794,5.747 7.159,5.951 1.364,0.205 10 Center Airbag Sensor 0.101,0.848 1.055,1.032 0.954,0.184 10 from IGN Fuse 0.101,2.637 1.101,2.820 1.000,0.184 10 from MET Fuse 0.233,3.246 1.019,3.616 0.787,0.371 10 from MET-B Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK BATTERY

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V




OK

3.CHECK CONNECTORS

NG

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
U152130E01
0.247,0.288 2.598,0.625 2.350,0.336 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.409,1.626 0.710,1.768 0.302,0.142 10 J46 1.049,3.078 1.289,3.234 0.239,0.156 10 E2 2.295,3.096 2.542,3.238 0.246,0.142 10 E1 2.854,2.339 3.128,2.502 0.274,0.163 10 IG2 1.677,2.485 1.238,3.053 false 1.797,2.468 2.321,3.07 false 2.407,2.425 2.82,2.425 false

a.

Disconnect the J46 center airbag sensor connector.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J46-21 (IG2) - J46-25 (E1) Ignition switch ON 11 to 14 V
J46-21 (IG2) - J46-26 (E2)




OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
U152218E02
0.99,2.521 1.677,2.99 false 0.677,2.385 0.292,2.854 false 0.781,2.396 0.917,2.865 false 0.49,0.51 2.865,0.844 2.375,0.333 10 false Front view of wire harness connector: (to Combination Meter) 0.24,1.594 0.531,1.74 0.292,0.146 10 false J28 0.219,2.885 0.375,3.042 0.156,0.156 10 false B 1.615,3 1.885,3.156 0.271,0.156 10 false ES 0.823,2.906 1.104,3.063 0.281,0.156 10 false IG+

a.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


b.

Disconnect the J28 combination meter connector.


c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage and resistance according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J28-2 (IG+) - J28-24 (ES) Ignition switch ON 11 to 14 V
J28-1 (B) - J28-24 (ES)

Standard resistance:
Tester Connection Condition Specified Condition
J28-24 (ES) - Body ground Always Below 1 Ω




OK

6.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, SRS warning light goes off for approximately 10 seconds and remains on.


Result
Result Proceed to
NG A
OK (for Column Shift Type) B
OK (for Floor Shift Type) C

HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned ON.




C

A

B