Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1650/32  Occupant Classification System Malfunction  


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor and the occupant classification system.

If the center airbag sensor receives signals from the occupant classification ECU, it determines whether the front passenger airbag, the front seat side airbag RH and front seat outer belt should be operated.

DTC B1650/32 is recorded when a malfunction is detected in the occupant classification system circuit.

DTC Code Detection Condition Trouble Area
B1650/32 When one of the following conditions is met:
·

Occupant classification system malfunction

·

The center airbag sensor receives a line short circuit, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit for 2 seconds.

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat wire RH

·

Occupant classification system

·

Center airbag sensor assembly



WIRING DIAGRAM

C167958E26
0.063,4.813 1.896,4.979 1.833,0.167 10 false Occupant Classification ECU 0.063,4.635 0.354,4.802 0.292,0.167 10 false Y2 3.396,1.74 3.719,1.885 0.323,0.146 10 false QY1 3.49,1.531 3.594,1.677 0.104,0.146 10 false 1 3.49,3.115 3.594,3.26 0.104,0.146 10 false 4 5.479,1.604 5.667,1.75 0.188,0.146 10 false 12 5.479,3.198 5.667,3.344 0.188,0.146 10 false 13 5.51,4.583 5.729,4.75 0.219,0.167 10 false Q1 5.51,4.75 6.99,4.917 1.479,0.167 10 false Center Airbag Sensor 0.833,1.708 1.25,1.896 0.417,0.188 10 false FSR+ 0.875,3.292 1.292,3.479 0.417,0.188 10 false FSR- 5.823,1.74 6.24,1.927 0.417,0.188 10 false FSP+ 5.813,3.333 6.229,3.521 0.417,0.188 10 false FSP- 1.406,1.594 1.552,1.76 0.146,0.167 10 false 8 1.417,3.208 1.563,3.396 0.146,0.188 10 false 4 3.396,3.323 3.75,3.469 0.354,0.146 10 false QY1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC (OCCUPANT CLASSIFICATION ECU)
a.

Turn the ignition switch to ON, and wait for at least 10 seconds.


b.

Check for the DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).



OK

2.CHECK FOR DTC (CENTER AIRBAG SENSOR)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK FOR DTC (CENTER AIRBAG SENSOR)
a.
C146235E11
0.063,1.188 1.563,1.542 1.5,0.354 10 false Occupant Classification ECU 2.021,1.063 2.917,1.417 0.896,0.354 10 false Center Airbag Sensor

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1650/32 is not output.


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

OK:

The connectors are properly connected.




OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the occupant classification ECU.


b.

Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged.

OK:

The connectors are not damaged or damaged.




OK

5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT
C353058E01
4.375,0.719 4.708,0.979 0.333,0.26 4.354,1.927 4.688,2.188 0.333,0.26 4.979,1.188 5.24,1 true 5.781,1.219 5.396,0.906 true 5.073,2.552 5.375,2.344 true 5.76,2.271 5.458,2.344 true 5.76,2.615 5.542,2.573 true 2.156,1.563 3.021,2.167 0.865,0.604 10 false Center Airbag Sensor 0.406,1.792 1.896,2.292 1.49,0.5 10 false Occupant Classification ECU 1.219,1.313 1.375,1.51 0.156,0.198 10 false F 1.5,1.083 1.656,1.281 0.156,0.198 10 false E 1.74,1.094 2.198,1.292 0.458,0.198 10 false D C 2.063,1.094 2.219,1.292 0.156,0.198 10 false B 2.344,1.313 2.5,1.51 0.156,0.198 10 false A 4.208,0.104 6.542,0.719 2.333,0.615 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.469,0.76 4.781,0.958 0.313,0.198 10 false Y2 5.927,0.833 6.729,1.031 0.802,0.198 10 false Connector E 4.75,1.188 5.365,1.385 0.615,0.198 10 false FSR+ 5.719,1.25 6.333,1.448 0.615,0.198 10 false FSR- 4.208,1.427 6.521,1.969 2.313,0.542 10 false Front view of wire harness connector: (to Center Airbag Sensor) 4.438,1.969 4.75,2.167 0.313,0.198 10 false Q1 5.823,1.948 6.625,2.146 0.802,0.198 10 false Connector B 4.688,2.469 5.052,2.667 0.365,0.198 10 false FSP- 5.813,2.167 6.177,2.365 0.365,0.198 10 false FSP+ 5.813,2.542 6.635,2.781 0.823,0.24 10 false Service Wire

a.

Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-4 (FSR-) - Y2-8 (FSR+) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-4 (FSR-) - Y2-8 (FSR+) Always 1 MΩ or higher
Y2-4 (FSR-) - Body ground
Y2-8 (FSR+) - Body ground



e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Y2-4 (FSR-) - Body ground Ignition switch ON Below 1 V
Y2-8 (FSR+) - Body ground


Result
Result Proceed to
OK (for Floor Shift Type) A
OK (for Column Shift Type) B
NG C



C

6.CHECK NO. 2 FLOOR WIRE

A

B

6.CHECK NO. 2 FLOOR WIRE
U152928E02
0.948,1.344 0.948,0.531 0.948,0.531 0.875,0.531 false 1.344,1.427 1.344,2.208 false 3.479,1.667 3.823,2.24 false 3.406,1.479 2.917,2.177 false 5.927,1.813 6.427,2.094 false 5.781,1.802 5.365,2.115 false 5.844,2.031 5.698,2.385 false 0.177,0.469 0.865,0.771 0.688,0.302 10 false Front Seat Wire RH 1.021,2.229 2.083,2.406 1.063,0.177 10 false No. 2 Floor Wire 0.469,1.292 0.604,1.448 0.135,0.156 10 false F 0.74,1.469 0.906,1.635 0.167,0.167 10 false E 1,1.469 1.156,1.615 0.156,0.146 10 false D 1.156,1.469 1.292,1.625 0.135,0.156 10 false C 1.448,1.458 1.604,1.656 0.156,0.198 10 false B 1.719,1.281 1.885,1.448 0.167,0.167 10 false A 0.146,1.656 1,2.177 0.854,0.521 10 false Occupant Classification ECU 1.615,1.531 2.521,1.865 0.906,0.333 10 false Center Airbag Sensor 2.354,0.073 4.771,0.438 2.417,0.365 10 false Front view of wire harness connector: (to Joining Connector) 4.813,0.083 7.135,0.448 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.406,0.979 3.229,1.146 0.823,0.167 10 false Connector C 4.531,1.042 5.365,1.219 0.833,0.177 10 false Connector B 2.688,1.365 3.01,1.542 0.323,0.177 10 false QY1 5.156,1.365 5.479,1.542 0.323,0.177 10 false Q1 5.135,2.406 5.958,2.594 0.823,0.188 10 false Service Wire 2.615,2.208 3.021,2.385 0.406,0.177 10 false FSR+ 3.698,2.271 4.104,2.448 0.406,0.177 10 false FSR- 6.292,2.115 6.708,2.271 0.417,0.156 10 false FSP+ 5.146,2.115 5.563,2.271 0.417,0.156 10 false FSP-

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the front seat wire RH connector from the No. 2 floor wire.


d.

Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.


e.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
QY1-1 (FSR+) - QY1-4 (FSR-) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
QY1-1 (FSR+) - QY1-4 (FSR-) Always 1 MΩ or higher
QY1-1 (FSR+) - Body ground
QY1-4 (FSR-) - Body ground



h.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
QY1-1 (FSR+) - Body ground Ignition switch ON Below 1 V
QY1-4 (FSR-) - Body ground




OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE