Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655/37  Driver Side Seat Belt Buckle Switch Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor and the front seat inner belt LH.

DTC B1655/37 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC Code Detection Condition Trouble Area
B1655/37 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.

·

Front seat inner belt LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C158843E19
2.448,3.021 2.698,3.25 0.25,0.229 10 false 2 2.448,1.448 2.573,1.615 0.125,0.167 10 false 1 2.021,1.229 2.438,1.385 0.417,0.156 10 false LBE+ 2.021,2.76 2.417,2.906 0.396,0.146 10 false LBE- 5.875,1.344 6.281,1.51 0.406,0.167 10 false LBE+ 5.583,1.49 5.833,1.656 0.25,0.167 10 false 11 0.323,3.938 0.677,4.083 0.354,0.146 10 false P7 0.333,4.135 2.5,4.281 2.167,0.146 10 false Front Seat Inner Belt LH 5.5,3.906 5.844,4.063 0.344,0.156 10 false P1 5.5,4.063 6.844,4.448 1.344,0.385 10 false Center Airbag Sensor 5.594,3.021 5.844,3.188 0.25,0.167 10 false 12 5.875,2.896 6.281,3.063 0.406,0.167 10 false LBE-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
C158841E01
0.526,0.995 1.467,1.366 0.941,0.371 10 Front Seat Inner Belt LH 1.785,1.08 2.726,1.430 0.941,0.350 10 Center Airbag Sensor

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.


b.

Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
U152930E02
4.083,2.198 3.698,1.49 false 3.458,1.49 3.031,2.104 false 0.99,1.094 0.99,0.594 0.99,0.594 0.865,0.594 false 5.771,1.885 6.26,2.208 false 5.656,1.896 5.177,2.198 false 5.792,2.25 5.958,2.5 false 0.177,0.51 0.854,0.656 0.677,0.146 10 false Floor Wire 0.427,1.052 0.563,1.24 0.135,0.188 10 false D 0.781,1.292 0.99,1.49 0.208,0.198 10 false C 1.104,1.281 1.333,1.49 0.229,0.208 10 false B 1.427,1.052 1.667,1.25 0.24,0.198 10 false A 1.271,1.583 2.188,1.885 0.917,0.302 10 false Center Airbag Sensor 0.042,1.469 0.927,1.792 0.885,0.323 10 false Front Seat Inner Belt LH 2.229,0.104 4.646,0.469 2.417,0.365 10 false Front view of wire harness connector: (to Front Seat Inner Belt LH) 4.75,0.115 7.073,0.479 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.74,1.344 3.01,1.542 0.271,0.198 10 false P7 4.698,1.573 4.906,1.74 0.208,0.167 10 false P1 3.948,2.25 4.375,2.406 0.427,0.156 10 false LBE+ 2.875,2.156 3.25,2.333 0.375,0.177 10 false LBE- 2.385,1.063 3.26,1.208 0.875,0.146 10 false Connector C 4.448,1.188 5.26,1.344 0.813,0.156 10 false Connector B 4.906,2.219 5.354,2.365 0.448,0.146 10 false DBE- 6.146,2.219 6.563,2.385 0.417,0.167 10 false DBE+ 5.875,2.521 6.708,2.688 0.833,0.167 10 false Service Wire

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
P7-1 (LBE+) - Body ground Ignition switch ON Below 1 V
P7-2 (LBE-) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P7-1 (LBE+) - P7-2 (LBE-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P7-1 (LBE+) - P7-2 (LBE-) Always 1 MΩ or higher
P7-1 (LBE+) - Body ground
P7-2 (LBE-) - Body ground




OK

5.CHECK FRONT SEAT INNER BELT LH

NG

REPLACE FLOOR WIRE

5.CHECK FRONT SEAT INNER BELT LH
C158841E04
0.526,0.995 1.467,1.366 0.941,0.371 10 Front Seat Inner Belt LH 1.785,1.08 2.726,1.430 0.941,0.350 10 Center Airbag Sensor

a.

Connect the connector to the center airbag sensor and the front seat inner belt LH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE FRONT SEAT INNER BELT LH
6.REPLACE FRONT SEAT INNER BELT LH
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform inspection using parts from a normal vehicle if possible.




NEXT

7.CHECK CENTER AIRBAG SENSOR
7.CHECK CENTER AIRBAG SENSOR
C158841E01
0.526,0.995 1.467,1.366 0.941,0.371 10 Front Seat Inner Belt LH 1.785,1.08 2.726,1.430 0.941,0.350 10 Center Airbag Sensor

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1655 is output (for Column Shift Type) A
DTC B1655 is output (for Floor Shift Type) B
DTC B1655 is not output C

HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




C

END (FRONT SEAT INNER BELT ASSEMBLY LH IS DEFECTIVE)

A

B