Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor and the passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag, front seat side airbag RH and front seat outer belt RH.

DTC B1660/43 is recorded when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC Code Detection Condition Trouble Area
B1660/43 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.

·

Passenger airbag ON/OFF indicator malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Air conditioning control assembly

·

Center airbag sensor assembly



WIRING DIAGRAM

C146242E26
0.446,4.621 0.893,4.807 0.448,0.186 10 J127 0.453,4.777 2.404,4.951 1.951,0.174 10 Air Conditioning Control 5.486,4.582 5.804,4.757 0.318,0.174 10 J46 5.473,4.744 6.879,4.928 1.406,0.184 10 Center Airbag Sensor 5.645,0.895 6.134,1.106 0.489,0.211 10 PAON 5.661,1.903 6.053,2.087 0.392,0.184 10 P-AB 1.634,1.819 1.914,1.975 0.281,0.156 10 2 1.634,0.806 1.845,0.976 0.211,0.170 10 3 1.634,2.815 1.876,2.985 0.243,0.170 10 4 1.875,3.904 3.517,4.079 1.642,0.175 10 from ECU-IG No. 2 Fuse 5.358,0.804 5.583,0.988 0.225,0.184 10 23 5.679,2.94 5.890,3.110 0.211,0.170 10 E1 5.679,3.893 5.890,4.063 0.211,0.170 10 E2 5.371,1.833 5.582,2.003 0.211,0.170 10 17 5.348,2.82 5.591,3.006 0.243,0.186 10 25 5.356,3.821 5.581,3.973 0.225,0.152 10 26 1.183,1.927 1.577,2.082 0.394,0.156 10 P-AB 1.125,0.93 1.573,1.092 0.448,0.163 10 PAON 1.289,2.94 1.567,3.096 0.279,0.156 10 IG+

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
C272587E13
3.125,0.979 3.854,1.146 0.729,0.167 10 false 4 seconds 4.031,0.896 4.719,1.063 0.688,0.167 10 false 2 seconds 3.125,1.948 3.854,2.115 0.729,0.167 10 false 4 seconds 4.031,1.917 4.719,2.083 0.688,0.167 10 false 2 seconds 4.615,3.073 6.792,3.438 2.177,0.365 10 false ON/OFF condition depends on the front passenger detection results. 0.313,2.448 1.521,3.083 1.208,0.635 10 false Passenger Airbag ON/OFF Indicator ("OFF") 0.281,1.448 1.521,2.083 1.24,0.635 10 false Passenger Airbag ON/OFF Indicator ("ON") 1.708,2.656 1.969,2.823 0.26,0.167 10 false Off 1.708,1.646 1.969,1.813 0.26,0.167 10 false Off 1.708,2.135 1.969,2.302 0.26,0.167 10 false On 1.708,1.167 1.969,1.333 0.26,0.167 10 false On 1.708,0.583 1.969,0.75 0.26,0.167 10 false Off 1.708,0.104 1.969,0.271 0.26,0.167 10 false On 0.375,0.323 1.448,0.51 1.073,0.188 10 false Ignition Switch

a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


Result
ON/OFF Indicator Illumination Proceed to
Remains ON A
Remains OFF B



A

2.CHECK CONNECTION OF CONNECTORS

B

7.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the air conditioning control.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the air conditioning control.


b.

Check that the connectors (on the center airbag sensor side and air conditioning control side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
C295051

a.

Connect the connector to the air conditioning control.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIR CONDITIONING CONTROL ASSEMBLY)
5.CHECK CENTER AIRBAG SENSOR
C146229E10
0.188,0.947 1.334,1.279 1.146,0.332 10 Passenger Airbag ON/OFF Indicator 1.662,1.255 2.572,1.600 0.911,0.346 10 Center Airbag Sensor

a.

Connect the connector to the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1660 is output (for Column Shift Type) A
DTC B1660 is output (for Floor Shift Type) B
DTC B1660 is not output C

HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




C

A

B

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIR CONDITIONING CONTROL ASSEMBLY)
U152931E02
0.865,0.208 1.115,0.208 1.115,0.208 1.115,1.188 false 3.708,1.635 3.948,2.198 false 6.125,1.615 6.563,1.917 false 3.49,1.656 3.198,2.24 false 5.802,1.51 5.24,1.927 false 5.698,2.01 5.156,2.479 false 0.073,1.604 1.271,1.917 1.198,0.313 10 false Air Conditioning Control 1.344,1.833 2.26,2.146 0.917,0.313 10 false Center Airbag Sensor 0.021,0.135 0.833,0.51 0.813,0.375 10 false Instrument Panel Wire 1.51,1.146 1.708,1.344 0.198,0.198 10 false A 1.219,1.333 1.417,1.531 0.198,0.198 10 false B 0.938,1.333 1.135,1.531 0.198,0.198 10 false C 0.646,1.146 0.844,1.344 0.198,0.198 10 false D 2.302,0.063 4.688,0.427 2.385,0.365 10 false Front view of wire harness connector: (to Air Conditioning Control) 4.823,0.063 7.146,0.427 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.75,1.438 3.417,1.615 0.667,0.177 10 false J127 4.979,1.448 5.24,1.625 0.26,0.177 10 false J46 3.792,2.24 4.25,2.385 0.458,0.146 10 false PAON 6.385,1.917 6.844,2.063 0.458,0.146 10 false PAON 2.99,2.323 3.448,2.469 0.458,0.146 10 false P-AB 5.052,1.938 5.51,2.083 0.458,0.146 10 false P-AB 2.302,0.896 3.156,1.104 0.854,0.208 10 false Connector C 4.573,0.917 5.427,1.125 0.854,0.208 10 false Connector B 4.344,2.375 5.177,2.552 0.833,0.177 10 false Service Wire

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connector from the air conditioning control.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J127-3 (PAON) - J127-2 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J127-3 (PAON) - J127-2 (P-AB) Always 1 MΩ or higher
J127-3 (PAON) - Body ground
J127-2 (P-AB) - Body ground



h.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J127-3 (PAON) - Body ground Ignition switch ON Below 1 V
J127-2 (P-AB) - Body ground




OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the air conditioning control.

OK:

The connectors are properly connected.




OK

8.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the air conditioning control.


b.

Check that the connectors (on the center airbag sensor side and air conditioning control side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIR CONDITIONING CONTROL ASSEMBLY)
U152931E02
0.865,0.208 1.115,0.208 1.115,0.208 1.115,1.188 false 3.708,1.635 3.948,2.198 false 6.125,1.615 6.563,1.917 false 3.49,1.656 3.198,2.24 false 5.802,1.51 5.24,1.927 false 5.698,2.01 5.156,2.479 false 0.073,1.604 1.271,1.917 1.198,0.313 10 false Air Conditioning Control 1.344,1.833 2.26,2.146 0.917,0.313 10 false Center Airbag Sensor 0.021,0.135 0.833,0.51 0.813,0.375 10 false Instrument Panel Wire 1.51,1.146 1.708,1.344 0.198,0.198 10 false A 1.219,1.333 1.417,1.531 0.198,0.198 10 false B 0.938,1.333 1.135,1.531 0.198,0.198 10 false C 0.646,1.146 0.844,1.344 0.198,0.198 10 false D 2.302,0.063 4.688,0.427 2.385,0.365 10 false Front view of wire harness connector: (to Air Conditioning Control) 4.823,0.063 7.146,0.427 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.75,1.438 3.417,1.615 0.667,0.177 10 false J127 4.979,1.448 5.24,1.625 0.26,0.177 10 false J46 3.792,2.24 4.25,2.385 0.458,0.146 10 false PAON 6.385,1.917 6.844,2.063 0.458,0.146 10 false PAON 2.99,2.323 3.448,2.469 0.458,0.146 10 false P-AB 5.052,1.938 5.51,2.083 0.458,0.146 10 false P-AB 2.302,0.896 3.156,1.104 0.854,0.208 10 false Connector C 4.573,0.917 5.427,1.125 0.854,0.208 10 false Connector B 4.344,2.375 5.177,2.552 0.833,0.177 10 false Service Wire

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connector from the air conditioning control.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J127-3 (PAON) - J127-2 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J127-3 (PAON) - J127-2 (P-AB) Always 1 MΩ or higher
J127-3 (PAON) - Body ground
J127-2 (P-AB) - Body ground



h.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J127-3 (PAON) - Body ground Ignition switch ON Below 1 V
J127-2 (P-AB) - Body ground




OK

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
U152932E02
2.083,2.25 2.406,2.406 true 0.448,0.177 2.792,0.563 2.344,0.385 10 false Front view of wire harness connector: (to Air Conditioning Control) 0.406,1.74 0.833,1.969 0.427,0.229 10 false J127 2.427,2.354 2.719,2.542 0.292,0.188 10 false IG+

a.

Connect the connectors to the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J127-4 (IG+) - Body ground Ignition switch ON 11 to 14 V




OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE HARNESS AND CONNECTOR (PASSENGER AIRBAG ON/OFF INDICATOR - BATTERY) OR BATTERY

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
U152264E01
0.316,0.27 2.645,0.648 2.330,0.378 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.52,1.863 0.808,2.026 0.288,0.163 10 J46 0.775,2.62 1.153,2.824 0.378,0.205 10 P-AB 2.281,2.62 2.694,2.824 0.413,0.205 10 PAON 2.017,2.131 2.487,2.584 false 1.591,1.961 0.974,2.608 false

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Connect the connector to the air conditioning control.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Check the indicator according to the value(s) in the table below.

Result:
Tester Connection Switch Condition Passenger airbag ON/OFF indicator
J46-23 (PAON) - Body ground Ignition switch ON "ON" comes on
J46-17 (P-AB) - Body ground Ignition switch ON "OFF" comes on




OK

12.CHECK CENTER AIRBAG SENSOR

NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY

12.CHECK CENTER AIRBAG SENSOR
C146229E61
0.303,0.966 1.483,1.306 1.180,0.340 10 Air Conditioning Control 1.739,1.276 2.630,1.598 0.891,0.323 10 Center Airbag Sensor

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Connect the connectors to the center airbag sensor.


d.

Connect the negative (-) terminal cable to the battery and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1660 is output (for Column Shift Type) A
DTC B1660 is output (for Floor Shift Type) B
DTC B1660 is not output C

HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




C

A

B