Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1610/13  Front Airbag Sensor RH Malfunction  B1615/14  Front Airbag Sensor LH Malfunction  


DESCRIPTION

The front airbag sensor LH and RH consists of the diagnostic circuit and the frontal deceleration sensor, etc.

If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.

DTC B1610/13 or B1615/14 is recorded when a malfunction is detected in the front airbag sensor LH and RH circuit.

DTC Code Detection Condition Trouble Area
B1610/13 When one of the following conditions is met:
·

Front airbag sensor RH malfunction

·

Center airbag sensor malfunction


·

Front airbag sensor RH

·

Center airbag sensor assembly


B1615/14 When one of the following conditions is met:
·

Front airbag sensor LH malfunction

·

Center airbag sensor malfunction


·

Front airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C158882E04
1.313,1.021 1.635,1.198 0.323,0.177 10 false +SR 1.333,2.198 1.625,2.375 0.292,0.177 10 false -SR 5.635,1.01 6.01,1.188 0.375,0.177 10 false +SR 5.656,2.188 6,2.365 0.344,0.177 10 false -SR 1.74,0.917 1.896,1.104 0.156,0.188 10 false 2 1.75,2.083 1.917,2.25 0.167,0.167 10 false 1 5.323,0.906 5.51,1.094 0.188,0.188 10 false 29 5.313,2.083 5.531,2.271 0.219,0.188 10 false 27 3.354,2.208 3.677,2.365 0.323,0.156 10 false AJ1 3.354,1.021 3.677,1.177 0.323,0.156 10 false AJ1 3.438,1.979 3.563,2.125 0.125,0.146 10 false 1 3.438,0.802 3.594,0.99 0.156,0.188 10 false 2 0.271,3.958 1.813,4.146 1.542,0.188 10 false Front Airbag Sensor RH 0.271,3.792 0.469,3.938 0.198,0.146 10 false A1 5.479,3.969 6.875,4.167 1.396,0.198 10 false Center Airbag Sensor 5.479,3.792 5.76,3.938 0.281,0.146 10 false J46 0.094,0.052 1.146,0.281 1.052,0.229 12 false for RH Side:

C158882E05
1.313,1 1.635,1.177 0.323,0.177 10 false +SL 1.333,2.177 1.625,2.354 0.292,0.177 10 false -SL 5.635,0.979 6.01,1.156 0.375,0.177 10 false +SL 5.656,2.156 6,2.333 0.344,0.177 10 false -SL 1.74,0.927 1.896,1.115 0.156,0.188 10 false 2 1.75,2.094 1.917,2.26 0.167,0.167 10 false 1 5.323,0.917 5.51,1.104 0.188,0.188 10 false 30 5.313,2.094 5.531,2.281 0.219,0.188 10 false 28 3.438,1.979 3.563,2.125 0.125,0.146 10 false 1 3.438,0.802 3.594,0.99 0.156,0.188 10 false 2 0.271,3.958 1.813,4.146 1.542,0.188 10 false Front Airbag Sensor LH 0.271,3.792 0.469,3.938 0.198,0.146 10 false A2 5.479,3.969 6.875,4.167 1.396,0.198 10 false Center Airbag Sensor 5.479,3.792 5.76,3.938 0.281,0.146 10 false J46 3.354,2.208 3.667,2.375 0.313,0.167 10 false AJ8 3.354,1.031 3.667,1.198 0.313,0.167 10 false AJ8 0.104,0.083 1.063,0.292 0.958,0.208 12 false for LH Side:

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1615 is output A
DTC B1610 and B1615 are not output B
DTC B1610 and B1615 are output C
DTC B1610 is output D



D

2.CHECK CONNECTION OF CONNECTORS

A

7.CHECK CONNECTION OF CONNECTORS

B

C

13.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front airbag sensor RH.


b.

Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
U152188E02
3.125,1.583 2.552,2.229 true 3.313,1.583 3.896,2.198 true 5.396,2.052 5.229,2.354 false 5.438,1.635 4.885,1.896 true 5.604,1.646 6.385,2.125 true 0.063,1.75 0.875,2.115 0.813,0.365 10 false Front Airbag Sensor RH 0.427,1.271 0.615,1.417 0.188,0.146 10 false F 0.677,1.5 0.844,1.667 0.167,0.167 10 false E 0.938,1.5 1.219,1.667 0.281,0.167 10 false DC 1.281,1.5 1.438,1.667 0.156,0.167 10 false B 1.563,1.323 1.708,1.49 0.146,0.167 10 false A 1.396,1.969 2.302,2.302 0.906,0.333 10 false Center Airbag Sensor 2.063,0.229 4.417,0.594 2.354,0.365 10 false Front view of wire harness connector: (to Front Airbag Sensor RH) 3.76,1.198 4.573,1.385 0.813,0.188 10 false Connector E 2.396,2.26 2.708,2.427 0.313,0.167 10 false -SR 3.813,2.24 4.146,2.406 0.333,0.167 10 false +SR 4.813,2.365 5.667,2.563 0.854,0.198 10 false Service Wire 4.656,0.24 6.99,0.604 2.333,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.563,1.854 4.896,2.021 0.333,0.167 10 false +SR 6.365,2.115 6.677,2.281 0.313,0.167 10 false -SR 2.406,1.198 2.635,1.344 0.229,0.146 10 false A1 4.802,1.125 5.073,1.271 0.271,0.146 10 false J46 6.313,1.219 7.125,1.406 0.813,0.188 10 false Connector B

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A1-1 (-SR) - Body ground Ignition switch ON Below 1 V
A1-2 (+SR) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A1-1 (-SR) - A1-2 (+SR) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A1-1 (-SR) - A1-2 (+SR) Always 1 MΩ or higher
A1-1 (-SR) - Body ground
A1-2 (+SR) - Body ground




OK

5.CHECK FRONT AIRBAG SENSOR RH

NG

6.CHECK INSTRUMENT PANEL WIRE
5.CHECK FRONT AIRBAG SENSOR RH
C172066E01
0.395,0.956 1.204,1.286 0.809,0.330 10 Front Airbag Sensor LH 1.917,1.32 2.816,1.653 0.899,0.333 10 Center Airbag Sensor

a.

Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1610 is output A
DTC B1615 is output B
DTC B1610 and B1615 are not output C

HINT:

Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.




C

A

12.REPLACE CENTER AIRBAG SENSOR

B

6.CHECK INSTRUMENT PANEL WIRE
C353036E01
2.698,1.281 3.052,1.521 0.354,0.24 4.76,1.271 5.115,1.51 0.354,0.24 0.885,1.271 0.885,0.354 0.885,0.354 1.073,0.354 false 1.281,2.448 1.281,1.385 false 2.979,2.021 3.469,1.552 true 4.313,2.01 3.76,1.563 true 6.188,2.271 5.635,1.823 true 4.979,2.292 5.469,1.823 true 5.417,2.396 5.479,2.198 true 2.469,0.146 4.75,0.74 2.281,0.594 10 false Front view of wire harness connector: (to Engine Room Main Wire) 4.813,0.146 7.094,0.74 2.281,0.594 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 1.177,0.26 2.094,0.854 0.917,0.594 10 false Engine Room Main Wire 0.792,2.458 2.198,2.667 1.406,0.208 10 false Instrument Panel Wire 0.083,1.625 0.906,2.083 0.823,0.458 10 false Front Airbag Sensor RH 0.375,1.25 0.531,1.448 0.156,0.198 10 false F 0.677,1.438 0.833,1.635 0.156,0.198 10 false E 0.969,1.427 1.125,1.625 0.156,0.198 10 false D 1.125,1.438 1.281,1.635 0.156,0.198 10 false C 1.396,1.438 1.552,1.635 0.156,0.198 10 false B 1.688,1.24 1.844,1.438 0.156,0.198 10 false A 1.49,1.906 2.385,2.427 0.896,0.521 10 false Center Airbag Sensor 4.115,1.604 5.802,1.802 1.688,0.198 10 false Connector C 6.354,1.615 7.156,1.875 0.802,0.26 10 false Connector B 2.771,1.323 3.229,1.521 0.458,0.198 10 false AJ1 4.833,1.313 5.292,1.51 0.458,0.198 10 false J46 2.833,2.031 3.292,2.229 0.458,0.198 10 false +SR 4.813,2.302 5.271,2.5 0.458,0.198 10 false +SR 4.198,2.031 4.656,2.229 0.458,0.198 10 false -SR 6.115,2.302 6.573,2.5 0.458,0.198 10 false -SR 5.156,2.427 6.99,2.625 1.833,0.198 10 false Service Wire

a.

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
AJ1-1 (-SR) - Body ground Ignition switch ON Below 1 V
AJ1-2 (+SR) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminal 27 (-SR) and 29 (+SR) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified Condition
AJ1-1 (-SR) - AJ1-2 (+SR) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
AJ1-1 (-SR) - AJ1-2 (+SR) Always 1 MΩ or higher
AJ1-1 (-SR) - Body ground
AJ1-2 (+SR) - Body ground




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor LH.

OK:

The connectors are properly connected.




OK

8.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front airbag sensor LH.


b.

Check that the connectors (on the center airbag sensor side and front airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

9.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

9.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
U152189E02
3.135,1.594 2.594,2.198 false 3.302,1.583 3.885,2.198 false 5.333,2.052 5.167,2.354 false 5.344,1.646 4.656,2.021 false 5.521,1.656 6.156,2.052 false 0.042,1.698 0.854,2.063 0.813,0.365 10 false Front Airbag Sensor LH 0.427,1.24 0.615,1.385 0.188,0.146 10 false F 0.688,1.469 0.854,1.635 0.167,0.167 10 false E 0.948,1.469 1.229,1.635 0.281,0.167 10 false DC 1.292,1.469 1.448,1.635 0.156,0.167 10 false B 1.573,1.292 1.719,1.458 0.146,0.167 10 false A 1.385,1.938 2.292,2.271 0.906,0.333 10 false Center Airbag Sensor 1.99,0.073 4.344,0.438 2.354,0.365 10 false Front view of wire harness connector: (to Front Airbag Sensor LH) 3.75,1.188 4.563,1.375 0.813,0.188 10 false Connector E 2.417,2.198 2.729,2.365 0.313,0.167 10 false -SL 3.854,2.198 4.188,2.365 0.333,0.167 10 false +SL 4.75,2.354 5.604,2.552 0.854,0.198 10 false Service Wire 4.51,0.083 6.844,0.448 2.333,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.469,2.042 4.802,2.208 0.333,0.167 10 false +SL 6.146,2.042 6.458,2.208 0.313,0.167 10 false -SL 2.417,1.198 2.646,1.344 0.229,0.146 10 false A2 4.875,1.198 5.146,1.344 0.271,0.146 10 false J46 6.323,1.167 7.146,1.344 0.823,0.177 10 false Connector B

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A2-1 (-SL) - Body ground Ignition switch ON Below 1 V
A2-2 (+SL) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A2-1 (-SL) - A2-2 (+SL) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A2-1 (-SL) - A2-2 (+SL) Always 1 MΩ or higher
A2-1 (-SL) - Body ground
A2-2 (+SL) - Body ground




OK

10.CHECK FRONT AIRBAG SENSOR LH

NG

11.CHECK INSTRUMENT PANEL WIRE
10.CHECK FRONT AIRBAG SENSOR LH
a.
C172066E03
0.395,0.956 1.204,1.285 0.809,0.330 10 Front Airbag Sensor RH 1.917,1.32 2.816,1.653 0.899,0.333 10 Center Airbag Sensor

Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1610 is output A
DTC B1615 is output B
DTC B1610 and B1615 are not output C

HINT:

Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.




C

A

B

12.REPLACE CENTER AIRBAG SENSOR
11.CHECK INSTRUMENT PANEL WIRE
U152205E02
0.875,1.26 0.875,0.396 0.875,0.396 1.042,0.396 false 1.302,1.375 1.302,2.438 false 3.51,1.417 3.063,1.854 false 3.844,1.448 4.323,1.896 false 5.354,1.833 4.979,2.125 false 5.563,1.802 6.073,2.125 false 5.313,2.167 5.229,2.365 false 0.052,1.615 0.865,1.99 0.813,0.375 10 false Front Airbag Sensor LH 1.521,1.885 2.417,2.24 0.896,0.354 10 false Center Airbag Sensor 0.979,1.406 1.177,1.573 0.198,0.167 10 false D 1.385,1.396 1.563,1.583 0.177,0.188 10 false B 1.677,1.219 1.844,1.385 0.167,0.167 10 false A 0.688,1.406 0.865,1.594 0.177,0.188 10 false E 0.417,1.219 0.542,1.406 0.125,0.188 10 false F 1.094,0.281 2.104,0.635 1.01,0.354 10 false Engine Room Main Wire 0.479,2.458 2.052,2.635 1.573,0.177 10 false Instrument Panel Wire 2.219,0.104 4.583,0.448 2.365,0.344 10 false Front view of wire harness connector: (to Engine Room Main Wire) 4.75,0.094 7.052,0.438 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.208,1.25 5.104,1.427 0.896,0.177 10 false Connector C 6.302,1.25 7.115,1.427 0.813,0.177 10 false Connector B 2.792,0.917 3.083,1.094 0.292,0.177 10 false AJ8 4.813,0.917 5.125,1.073 0.313,0.156 10 false J46 4.365,1.875 4.667,2.063 0.302,0.188 10 false -SL 2.802,1.865 3.104,2.052 0.302,0.188 10 false +SL 6.104,2.104 6.406,2.292 0.302,0.188 10 false -SL 4.677,2.094 4.99,2.302 0.313,0.208 10 false +SL 4.771,2.354 5.688,2.552 0.917,0.198 10 false Service Wire 1.115,1.396 1.25,1.615 0.135,0.219 10 false C

a.

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
AJ8-1 (-SL) - Body ground Ignition switch ON Below 1 V
AJ8-2 (+SL) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminal 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified Condition
AJ8-1 (-SL) - AJ8-2 (+SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
AJ8-1 (-SL) - AJ8-2 (+SL) Always 1 MΩ or higher
AJ8-1 (-SL) - Body ground
AJ8-2 (+SL) - Body ground




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

12.REPLACE CENTER AIRBAG SENSOR
a.
C167366E02
0.167,0.927 1.688,1.125 1.521,0.198 10 false Front Airbag Sensor RH 1.677,2.896 3.083,3.094 1.406,0.198 10 false Center Airbag Sensor 0.125,2.104 1.74,2.344 1.615,0.24 10 false Front Airbag Sensor LH

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the center airbag sensor.


ii.

for Floor Shift Type (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY(for Floor Shift Type)>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




d.

Connect the connectors to the center airbag sensor.


e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1610 and B1615 are not output.


HINT:

Codes other than B1610 may be output at this time, but they are not related to this check.




OK

END

NG

REPLACE FRONT AIRBAG SENSOR RH AND LH

13.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH and LH.

OK:

The connectors are properly connected.




OK

14.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

14.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front airbag sensor RH and LH.


b.

Check that the connectors (on the center airbag sensor side and front airbag sensor RH and LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

15.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

15.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
U152188E02
3.125,1.583 2.552,2.229 true 3.313,1.583 3.896,2.198 true 5.396,2.052 5.229,2.354 false 5.438,1.635 4.885,1.896 true 5.604,1.646 6.385,2.125 true 0.063,1.75 0.875,2.115 0.813,0.365 10 false Front Airbag Sensor RH 0.427,1.271 0.615,1.417 0.188,0.146 10 false F 0.677,1.5 0.844,1.667 0.167,0.167 10 false E 0.938,1.5 1.219,1.667 0.281,0.167 10 false DC 1.281,1.5 1.438,1.667 0.156,0.167 10 false B 1.563,1.323 1.708,1.49 0.146,0.167 10 false A 1.396,1.969 2.302,2.302 0.906,0.333 10 false Center Airbag Sensor 2.063,0.229 4.417,0.594 2.354,0.365 10 false Front view of wire harness connector: (to Front Airbag Sensor RH) 3.76,1.198 4.573,1.385 0.813,0.188 10 false Connector E 2.396,2.26 2.708,2.427 0.313,0.167 10 false -SR 3.813,2.24 4.146,2.406 0.333,0.167 10 false +SR 4.813,2.365 5.667,2.563 0.854,0.198 10 false Service Wire 4.656,0.24 6.99,0.604 2.333,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.563,1.854 4.896,2.021 0.333,0.167 10 false +SR 6.365,2.115 6.677,2.281 0.313,0.167 10 false -SR 2.406,1.198 2.635,1.344 0.229,0.146 10 false A1 4.802,1.125 5.073,1.271 0.271,0.146 10 false J46 6.313,1.219 7.125,1.406 0.813,0.188 10 false Connector B

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A1-1 (-SR) - Body ground Ignition switch ON Below 1 V
A1-2 (+SR) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A1-1 (-SR) - A1-2 (+SR) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A1-1 (-SR) - A1-2 (+SR) Always 1 MΩ or higher
A1-1 (-SR) - Body ground
A1-2 (+SR) - Body ground




OK

16.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

NG

18.CHECK INSTRUMENT PANEL WIRE
16.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
U152189E02
3.135,1.594 2.594,2.198 false 3.302,1.583 3.885,2.198 false 5.333,2.052 5.167,2.354 false 5.344,1.646 4.656,2.021 false 5.521,1.656 6.156,2.052 false 0.042,1.698 0.854,2.063 0.813,0.365 10 false Front Airbag Sensor LH 0.427,1.24 0.615,1.385 0.188,0.146 10 false F 0.688,1.469 0.854,1.635 0.167,0.167 10 false E 0.948,1.469 1.229,1.635 0.281,0.167 10 false DC 1.292,1.469 1.448,1.635 0.156,0.167 10 false B 1.573,1.292 1.719,1.458 0.146,0.167 10 false A 1.385,1.938 2.292,2.271 0.906,0.333 10 false Center Airbag Sensor 1.99,0.073 4.344,0.438 2.354,0.365 10 false Front view of wire harness connector: (to Front Airbag Sensor LH) 3.75,1.188 4.563,1.375 0.813,0.188 10 false Connector E 2.417,2.198 2.729,2.365 0.313,0.167 10 false -SL 3.854,2.198 4.188,2.365 0.333,0.167 10 false +SL 4.75,2.354 5.604,2.552 0.854,0.198 10 false Service Wire 4.51,0.083 6.844,0.448 2.333,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.469,2.042 4.802,2.208 0.333,0.167 10 false +SL 6.146,2.042 6.458,2.208 0.313,0.167 10 false -SL 2.417,1.198 2.646,1.344 0.229,0.146 10 false A2 4.875,1.198 5.146,1.344 0.271,0.146 10 false J46 6.323,1.167 7.146,1.344 0.823,0.177 10 false Connector B

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A2-1 (-SL) - Body ground Ignition switch ON Below 1 V
A2-2 (+SL) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A2-1 (-SL) - A2-2 (+SL) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A2-1 (-SL) - A2-2 (+SL) Always 1 MΩ or higher
A2-1 (-SL) - Body ground
A2-2 (+SL) - Body ground




OK

17.REPLACE FRONT AIRBAG SENSOR RH AND LH

NG

19.CHECK INSTRUMENT PANEL WIRE
17.REPLACE FRONT AIRBAG SENSOR RH AND LH
a.
C167366E03
0.167,0.948 1.688,1.146 1.521,0.198 10 false Front Airbag Sensor RH 1.677,2.896 3.083,3.094 1.406,0.198 10 false Center Airbag Sensor 0.125,2.115 1.74,2.354 1.615,0.24 10 false Front Airbag Sensor LH

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front airbag sensor RH and LH (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1610 and B1615 are not output.


HINT:

Codes other than B1610 and B1615 may be output at this time, but they are not related to this check.


Result
Result Proceed to
NG (for Floor Shift Type) A
NG (for Column Shift Type) B
OK C



C

END

A

B

18.CHECK INSTRUMENT PANEL WIRE
C353036E01
2.698,1.281 3.052,1.521 0.354,0.24 4.76,1.271 5.115,1.51 0.354,0.24 0.885,1.271 0.885,0.354 0.885,0.354 1.073,0.354 false 1.281,2.448 1.281,1.385 false 2.979,2.021 3.469,1.552 true 4.313,2.01 3.76,1.563 true 6.188,2.271 5.635,1.823 true 4.979,2.292 5.469,1.823 true 5.417,2.396 5.479,2.198 true 2.469,0.146 4.75,0.74 2.281,0.594 10 false Front view of wire harness connector: (to Engine Room Main Wire) 4.813,0.146 7.094,0.74 2.281,0.594 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 1.177,0.26 2.094,0.854 0.917,0.594 10 false Engine Room Main Wire 0.792,2.458 2.198,2.667 1.406,0.208 10 false Instrument Panel Wire 0.083,1.625 0.906,2.083 0.823,0.458 10 false Front Airbag Sensor RH 0.375,1.25 0.531,1.448 0.156,0.198 10 false F 0.677,1.438 0.833,1.635 0.156,0.198 10 false E 0.969,1.427 1.125,1.625 0.156,0.198 10 false D 1.125,1.438 1.281,1.635 0.156,0.198 10 false C 1.396,1.438 1.552,1.635 0.156,0.198 10 false B 1.688,1.24 1.844,1.438 0.156,0.198 10 false A 1.49,1.906 2.385,2.427 0.896,0.521 10 false Center Airbag Sensor 4.115,1.604 5.802,1.802 1.688,0.198 10 false Connector C 6.354,1.615 7.156,1.875 0.802,0.26 10 false Connector B 2.771,1.323 3.229,1.521 0.458,0.198 10 false AJ1 4.833,1.313 5.292,1.51 0.458,0.198 10 false J46 2.833,2.031 3.292,2.229 0.458,0.198 10 false +SR 4.813,2.302 5.271,2.5 0.458,0.198 10 false +SR 4.198,2.031 4.656,2.229 0.458,0.198 10 false -SR 6.115,2.302 6.573,2.5 0.458,0.198 10 false -SR 5.156,2.427 6.99,2.625 1.833,0.198 10 false Service Wire

a.

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
AJ1-1 (-SR) - Body ground Ignition switch ON Below 1 V
AJ1-2 (+SR) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminal 27 (-SR) and 29 (+SR) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified Condition
AJ1-1 (-SR) - AJ1-2 (+SR) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
AJ1-1 (-SR) - AJ1-2 (+SR) Always 1 MΩ or higher
AJ1-1 (-SR) - Body ground
AJ1-2 (+SR) - Body ground




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

19.CHECK INSTRUMENT PANEL WIRE
U152205E02
0.875,1.26 0.875,0.396 0.875,0.396 1.042,0.396 false 1.302,1.375 1.302,2.438 false 3.51,1.417 3.063,1.854 false 3.844,1.448 4.323,1.896 false 5.354,1.833 4.979,2.125 false 5.563,1.802 6.073,2.125 false 5.313,2.167 5.229,2.365 false 0.052,1.615 0.865,1.99 0.813,0.375 10 false Front Airbag Sensor LH 1.521,1.885 2.417,2.24 0.896,0.354 10 false Center Airbag Sensor 0.979,1.406 1.177,1.573 0.198,0.167 10 false D 1.385,1.396 1.563,1.583 0.177,0.188 10 false B 1.677,1.219 1.844,1.385 0.167,0.167 10 false A 0.688,1.406 0.865,1.594 0.177,0.188 10 false E 0.417,1.219 0.542,1.406 0.125,0.188 10 false F 1.094,0.281 2.104,0.635 1.01,0.354 10 false Engine Room Main Wire 0.479,2.458 2.052,2.635 1.573,0.177 10 false Instrument Panel Wire 2.219,0.104 4.583,0.448 2.365,0.344 10 false Front view of wire harness connector: (to Engine Room Main Wire) 4.75,0.094 7.052,0.438 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.208,1.25 5.104,1.427 0.896,0.177 10 false Connector C 6.302,1.25 7.115,1.427 0.813,0.177 10 false Connector B 2.792,0.917 3.083,1.094 0.292,0.177 10 false AJ8 4.813,0.917 5.125,1.073 0.313,0.156 10 false J46 4.365,1.875 4.667,2.063 0.302,0.188 10 false -SL 2.802,1.865 3.104,2.052 0.302,0.188 10 false +SL 6.104,2.104 6.406,2.292 0.302,0.188 10 false -SL 4.677,2.094 4.99,2.302 0.313,0.208 10 false +SL 4.771,2.354 5.688,2.552 0.917,0.198 10 false Service Wire 1.115,1.396 1.25,1.615 0.135,0.219 10 false C

a.

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
AJ8-1 (-SL) - Body ground Ignition switch ON Below 1 V
AJ8-2 (+SL) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminal 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified Condition
AJ8-1 (-SL) - AJ8-2 (+SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
AJ8-1 (-SL) - AJ8-2 (+SL) Always 1 MΩ or higher
AJ8-1 (-SL) - Body ground
AJ8-2 (+SL) - Body ground




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE