Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt RH.

DTC B1771 is recorded when a malfunction is detected in the passenger side buckle switch circuit.

Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are output simultaneously.

DTC Code DTC Detection Condition Trouble Area
B1771 One of following conditions is met:
·

Occupant classification ECU detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in passenger side buckle switch circuit for 2 seconds

·

Passenger side buckle switch malfunction

·

Occupant classification ECU malfunction


·

Front seat wire RH

·

Front seat inner belt RH (Passenger side buckle switch)

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1771 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.



WIRING DIAGRAM

C253566E47
5.115,4.073 6.896,4.583 1.781,0.51 10 false Occupant Classification ECU 0.417,4.094 2.427,4.656 2.01,0.563 10 false Front Seat Inner Belt RH (Passenger Side Buckle Switch) 5.844,2.948 6.271,3.135 0.427,0.188 10 false RBE- 5.125,3.896 5.469,4.073 0.344,0.177 10 false Y2 0.427,3.948 0.771,4.125 0.344,0.177 10 false Y3 5.844,1.375 6.271,1.573 0.427,0.198 10 false RBE+ 2.031,2.844 2.448,3.042 0.417,0.198 10 false RBE- 2.042,1.292 2.5,1.5 0.458,0.208 10 false RBE+ 5.583,2.854 5.781,3.042 0.198,0.188 10 false 18 5.573,1.281 5.75,1.469 0.177,0.188 10 false 10 2.448,2.844 2.594,3.031 0.146,0.188 10 false 3 2.448,1.292 2.594,1.479 0.146,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt RH.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.

Disconnect the connectors from the occupant classification ECU and the front seat inner belt RH.


b.

Check that the connectors (on the occupant classification ECU side and passenger side buckle switch side) are not damaged (see page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.




OK

4.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH
U152939E02
0.771,0.479 0.896,0.479 0.896,0.479 1.125,1.365 false 6.354,1.427 6.594,1.167 false 6.104,1.573 6.563,1.99 false 3.896,1.625 4.354,2.031 false 3.698,1.615 3.302,2.021 false 3.781,1.969 3.781,2.188 false 0.042,0.427 0.74,0.813 0.698,0.385 10 false Front Seat Wire RH 0.542,1.271 0.677,1.448 0.135,0.177 10 false D 1.656,1.375 1.792,1.552 0.135,0.177 10 false A 0.854,1.563 0.99,1.74 0.135,0.177 10 false C 1.313,1.563 1.448,1.74 0.135,0.177 10 false B 1.5,1.927 2.375,2.427 0.875,0.5 10 false Occupant Classification ECU 0.125,1.708 0.833,2.229 0.708,0.521 10 false Front Seat Inner Belt RH 2.396,0.813 3.26,1.031 0.865,0.219 10 false Connector C 2.656,1.313 2.885,1.49 0.229,0.177 10 false Y3 3.417,2.229 4.26,2.448 0.844,0.219 10 false Service Wire 4.771,0.802 5.635,1.021 0.865,0.219 10 false Connector B 6.667,1.052 7.115,1.271 0.448,0.219 10 false BGND 6.615,1.896 6.969,2.115 0.354,0.219 10 false BSW 2.208,0.156 4.594,0.51 2.385,0.354 10 false Front view of wire harness connector: (to Front Seat Inner Belt RH) 4.719,0.146 7.135,0.5 2.417,0.354 10 false Front view of wire harness connector: (to Occupant Classification ECU) 5.115,1.344 5.344,1.521 0.229,0.177 10 false Y2 4.396,1.969 4.885,2.188 0.49,0.219 10 false RBE- 2.917,1.948 3.406,2.167 0.49,0.219 10 false RBE+

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Y2-9 (BSW) - Body ground Ignition switch ON Below 1 V
Y2-5 (BGND) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (RBE+) and 2 (RBE-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-9 (BSW) - Y2-5 (BGND) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-9 (BSW) - Body ground Always 1 MΩ or higher
Y2-5 (BGND) - Body ground
Y2-9 (BSW) - Y2-5 (BGND)




OK

5.CHECK FOR DTC

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the front seat inner belt RH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (see page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




OK

END

NG

7.REPLACE OCCUPANT CLASSIFICATION ECU
7.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

If the DTCs are not cleared at this time, past DTCs will remain.




NEXT

8.PERFORM ZERO POINT CALIBRATION
8.PERFORM ZERO POINT CALIBRATION
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

9.PERFORM SENSITIVITY CHECK
9.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END