Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1790  Center Airbag Sensor Assembly Communication Circuit Malfunction  


DESCRIPTION

The center airbag sensor communication circuit consists of the occupant classification ECU and the center airbag sensor.

DTC B1790 is set when a malfunction is detected in the center airbag sensor communication circuit.

DTC Code DTC Detection Condition Trouble Area
B1790 One of following conditions is met:
·

Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in center airbag sensor communication circuit for 2 seconds

·

Center airbag sensor malfunction

·

Occupant classification ECU malfunction


·

No. 2 floor wire

·

Front seat wire RH

·

Occupant classification ECU

·

Center airbag sensor



HINT:
·

When DTC B1630/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1790 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C167958E25
0.063,4.808 1.895,4.978 1.832,0.170 10 Occupant Classification ECU 0.063,4.635 0.353,4.805 0.290,0.170 10 Y2 3.401,1.721 3.725,1.865 0.325,0.144 10 QY1 3.486,1.532 3.591,1.676 0.105,0.144 10 1 3.486,3.118 3.591,3.263 0.105,0.144 10 4 5.478,1.599 5.669,1.745 0.191,0.145 10 12 5.478,3.197 5.669,3.342 0.191,0.145 10 13 5.508,4.579 5.727,4.744 0.218,0.165 10 Q1 5.508,4.754 6.984,4.919 1.475,0.165 10 Center Airbag Sensor 0.834,1.704 1.246,1.895 0.413,0.191 10 FSR+ 0.876,3.288 1.288,3.478 0.413,0.191 10 FSR- 5.828,1.711 6.241,1.902 0.413,0.191 10 FSP+ 5.814,3.302 6.227,3.492 0.413,0.191 10 FSP- 1.408,1.592 1.550,1.762 0.142,0.170 10 8 1.415,3.211 1.557,3.401 0.142,0.191 10 4 3.401,3.302 3.753,3.446 0.352,0.144 10 QY1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.

Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (see page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.




OK

4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT

NG

REPLACE HARNESS OR CONNECTOR

4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT
C353058E01
4.375,0.719 4.708,0.979 0.333,0.26 4.354,1.927 4.688,2.188 0.333,0.26 4.979,1.188 5.24,1 true 5.781,1.219 5.396,0.906 true 5.073,2.552 5.375,2.344 true 5.76,2.271 5.458,2.344 true 5.76,2.615 5.542,2.573 true 2.156,1.563 3.021,2.167 0.865,0.604 10 false Center Airbag Sensor 0.406,1.792 1.896,2.292 1.49,0.5 10 false Occupant Classification ECU 1.219,1.313 1.375,1.51 0.156,0.198 10 false F 1.5,1.083 1.656,1.281 0.156,0.198 10 false E 1.74,1.094 2.198,1.292 0.458,0.198 10 false D C 2.063,1.094 2.219,1.292 0.156,0.198 10 false B 2.344,1.313 2.5,1.51 0.156,0.198 10 false A 4.208,0.104 6.542,0.719 2.333,0.615 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.469,0.76 4.781,0.958 0.313,0.198 10 false Y2 5.927,0.833 6.729,1.031 0.802,0.198 10 false Connector E 4.75,1.188 5.365,1.385 0.615,0.198 10 false FSR+ 5.719,1.25 6.333,1.448 0.615,0.198 10 false FSR- 4.208,1.427 6.521,1.969 2.313,0.542 10 false Front view of wire harness connector: (to Center Airbag Sensor) 4.438,1.969 4.75,2.167 0.313,0.198 10 false Q1 5.823,1.948 6.625,2.146 0.802,0.198 10 false Connector B 4.688,2.469 5.052,2.667 0.365,0.198 10 false FSP- 5.813,2.167 6.177,2.365 0.365,0.198 10 false FSP+ 5.813,2.542 6.635,2.781 0.823,0.24 10 false Service Wire

a.

Disconnect the connectors from the occupant classification ECU and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Y2-8 (FSR+) - Body ground Ignition switch ON Below 1 V
Y2-4 (FSR-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-8 (FSR+) - Y2-4 (FSR-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-8 (FSR+) - Y2-4 (FSR-) Always 1 MΩ or higher
Y2-8 (FSR+) - Body ground
Y2-4 (FSR-) - Body ground




OK

5.CHECK FOR DTC

NG

10.CHECK FRONT SEAT WIRE RH
5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear any DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE OCCUPANT CLASSIFICATION ECU
6.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

8.PERFORM SENSITIVITY CHECK
8.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.


Result
Result Proceed to
DTC B1790 is not output A
DTC B1790 is output (for Column Shift Type) B
DTC B1790 is output (for Floor Shift Type) C



A

END

B

C

10.CHECK FRONT SEAT WIRE RH
U152919E02
3.656,1.521 3.156,2.083 true 6.188,1.469 6.521,1.646 true 3.917,1.417 4.49,2.01 true 6.188,1.302 6.521,1.219 true 1.115,1.531 1.115,0.781 1.115,0.781 1.042,0.781 false 1.479,1.521 1.479,0.49 1.479,0.49 1.406,0.49 false 3.781,1.896 3.781,2.208 false 1.698,1.667 2.583,2.021 0.885,0.354 10 false Center Airbag Sensor 2.302,0.021 4.646,0.427 2.344,0.406 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.792,0 7.135,0.406 2.344,0.406 10 false Front view of wire harness connector: (to Front Seat Wire RH) 2.552,0.802 3.385,1 0.833,0.198 10 false Connector E 2.76,2.021 3.167,2.219 0.406,0.198 10 false FSR+ 4.542,1.958 4.948,2.156 0.406,0.198 10 false FSR- 4.656,0.823 5.49,1.021 0.833,0.198 10 false Connector D 0.333,1.833 1.271,2.354 0.938,0.521 10 false Occupant Classification ECU 0.021,0.708 1.042,1.052 1.021,0.344 10 false Front Seat Wire RH 0.76,1.458 0.917,1.625 0.156,0.167 10 false F 1.792,1.458 1.948,1.625 0.156,0.167 10 false A 1.344,1.292 1.479,1.458 0.135,0.167 10 false C 1.229,1.292 1.365,1.458 0.135,0.167 10 false D 0.99,1.292 1.125,1.458 0.135,0.167 10 false E 1.542,1.292 1.677,1.458 0.135,0.167 10 false B 6.583,1.563 6.948,1.76 0.365,0.198 10 false FSR- 6.563,1.125 6.969,1.323 0.406,0.198 10 false FSR+ 3,1.25 3.271,1.417 0.271,0.167 10 false Y2 4.948,1.208 5.292,1.375 0.344,0.167 10 false QY1 0.333,0.396 1.417,0.583 1.083,0.188 10 false No. 2 Floor Wire 3.406,2.25 4.542,2.448 1.135,0.198 10 false Service Wire

a.

Disconnect the front seat wire RH connector from the No. 2 floor wire.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
QY1-1 (FSR+) - Body ground Ignition switch ON Below 1 V
QY1-4 (FSR-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the connector from the occupant classification ECU.


g.

Using a service wire, connect terminals 1 (FSR+) and 4 (FSR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
QY1-1 (FSR+) - QY1-4 (FSR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
QY1-1 (FSR+) - QY1-4 (FSR-) Always 1 MΩ or higher
QY1-1 (FSR+) - Body ground
QY1-4 (FSR-) - Body ground




OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT SEAT WIRE RH