Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1793  Occupant Classification Sensor Power Supply Circuit Malfunction  


DESCRIPTION

The occupant detection sensor power supply circuit consists of the occupant classification ECU and the occupant detection sensors.

DTC B1793 is set when a malfunction is detected in the occupant detection sensor power supply circuit.

DTC Code DTC Detection Condition Trouble Area
B1793 One of following conditions is met:
·

Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in occupant detection sensor power supply circuit for 2 seconds

·

Open circuit in occupant detection sensor wire harness

·

Occupant classification ECU malfunction


·

Front seat frame with adjuster RH (Occupant detection sensors)

·

Front seat wire RH

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1793 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

E146076E12
1.227,1.191 1.607,1.372 0.380,0.181 10 SVC 1.22,2.677 1.600,2.859 0.380,0.181 10 SVC 1.62,1.079 1.775,1.260 0.156,0.181 10 1 1.62,2.556 1.775,2.737 0.156,0.181 10 1 1.62,4.052 1.775,4.234 0.156,0.181 10 1 1.62,5.557 1.775,5.738 0.156,0.181 10 1 1.205,4.183 1.584,4.364 0.380,0.181 10 SVC 1.212,5.681 1.592,5.862 0.380,0.181 10 SVC 0.115,6.111 0.317,6.292 0.202,0.181 10 Y7 5.261,6.125 5.463,6.306 0.202,0.181 10 Y1 0.115,6.286 2.641,6.467 2.526,0.181 10 Rear Occupant Detection Sensor RH 0.115,4.605 0.317,4.786 0.202,0.181 10 Y6 0.115,4.78 2.641,4.961 2.526,0.181 10 Rear Occupant Detection Sensor LH 0.115,3.098 0.317,3.280 0.202,0.181 10 Y5 0.115,3.274 2.641,3.455 2.526,0.181 10 Front Occupant Detection Sensor RH 0.115,1.599 0.317,1.781 0.202,0.181 10 Y4 0.115,1.774 2.641,1.956 2.526,0.181 10 Front Occupant Detection Sensor LH 5.261,6.289 7.061,6.470 1.800,0.181 10 Occupant Classification ECU 5.487,1.058 5.658,1.239 0.171,0.181 10 11 5.487,2.515 5.658,2.697 0.171,0.181 10 12 5.567,4.03 5.722,4.211 0.156,0.181 10 5 5.567,5.539 5.722,5.720 0.156,0.181 10 6 5.804,1.191 6.184,1.372 0.380,0.181 10 SVC1 5.804,2.677 6.184,2.859 0.380,0.181 10 SVC2 5.804,4.183 6.184,4.364 0.380,0.181 10 SVC3 5.804,5.681 6.184,5.862 0.380,0.181 10 SVC4

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1793 is not output.


HINT:

DTCs other than DTC B1793 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the occupant detection sensors.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.

Check that the connectors (on the occupant classification ECU side and the occupant detection sensors side) are not damaged (see page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.




OK

4.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH
a.

Disconnect the connectors from the occupant classification ECU and the 4 occupant detection sensors.

U152731E02
1.26,0.656 1.302,0.615 false 1.26,0.708 1.344,0.615 false 1.26,0.76 1.344,0.677 false 1.26,0.813 1.344,0.729 false 1.302,0.823 1.344,0.781 false 2.094,4.375 1.896,4.604 true 5.115,4.375 4.917,4.604 true 3.917,3.063 3.75,3.333 true 1.375,0.125 1.5,0.125 1.5,0.125 1.5,0.677 false 0.896,3.063 0.74,3.333 true 5.146,0.99 5.427,0.906 true 5.073,0.99 5.365,0.708 true 5.052,1.094 5.219,1.375 true 5.156,1.073 5.438,1.229 true 0.115,0.073 1.354,0.271 1.24,0.198 10 false Front Seat Wire RH 1.854,1.031 3.667,1.219 1.813,0.188 10 false Occupant Classification ECU 0.031,1.052 1.302,1.396 1.271,0.344 10 false Occupant Detection Sensor 0.083,2.208 2.625,2.552 2.542,0.344 10 false Front view of wire harness connector: (to Front Occupant Detection Sensor LH) 3.125,2.208 5.698,2.552 2.573,0.344 10 false Front view of wire harness connector: (to Front Occupant Detection Sensor RH) 0.854,3.583 3.427,3.927 2.573,0.344 10 false Front view of wire harness connector: (to Front Occupant Detection Sensor LH) 3.896,3.583 6.469,3.927 2.573,0.344 10 false Front view of wire harness connector: (to Front Occupant Detection Sensor RH) 2.042,0.667 2.219,0.865 0.177,0.198 10 false A 1.719,0.865 1.896,1.063 0.177,0.198 10 false B 1.25,0.865 1.427,1.063 0.177,0.198 10 false C 0.927,0.667 1.083,0.865 0.156,0.198 10 false E 1.469,4.302 1.719,4.448 0.25,0.146 10 false Y6 1.698,4.604 2.104,4.771 0.406,0.167 10 false SVC 4.49,4.302 4.74,4.448 0.25,0.146 10 false Y7 4.729,4.604 5.135,4.771 0.406,0.167 10 false SVC 3.292,2.99 3.542,3.135 0.25,0.146 10 false Y5 3.563,3.354 3.969,3.521 0.406,0.167 10 false SVC 1.469,2.99 2.292,3.146 0.823,0.156 10 false Connector C 4.604,2.99 5.427,3.146 0.823,0.156 10 false Connector C 2.677,4.292 3.5,4.448 0.823,0.156 10 false Connector C 5.813,4.292 6.635,4.448 0.823,0.156 10 false Connector C 3.844,0.031 6.219,0.396 2.375,0.365 10 false Front view of wire harness connector: (to Occupant Classification ECU) 5.979,0.948 6.844,1.135 0.865,0.188 10 false Connector B 0.271,2.99 0.521,3.135 0.25,0.146 10 false Y4 0.531,3.354 0.938,3.521 0.406,0.167 10 false SVC 4.083,0.917 4.333,1.063 0.25,0.146 10 false Y1 5.49,0.802 5.917,0.99 0.427,0.188 10 false SVC4 5.417,0.594 5.844,0.781 0.427,0.188 10 false SVC3 5.5,1.167 5.927,1.354 0.427,0.188 10 false SVC2 5.24,1.354 5.667,1.542 0.427,0.188 10 false SVC1


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Y1-11 (SVC1) - Body ground Ignition switch ON Below 1 V
Y1-12 (SVC2) - Body ground
Y1-5 (SVC3) - Body ground
Y1-6 (SVC4) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
Y1-11 (SVC1) - Y4-1 (SVC) Always Below 1 Ω
Y1-12 (SVC2) - Y5-1 (SVC)
Y1-5 (SVC3) - Y6-1 (SVC)
Y1-6 (SVC4) - Y7-1 (SVC)



h.

Measure the resistance according the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y1-11 (SVC1) - Body ground Always 1 MΩ or higher
Y1-12 (SVC2) - Body ground
Y1-5 (SVC3) - Body ground
Y1-6 (SVC4) - Body ground
Y1-11 (SVC1) - Y1-12 (SVC)
Y1-11 (SVC1) - Y1-6 (SVC)
Y1-12 (SVC2) - Y1-5 (SVC)
Y1-12 (SVC2) - Y1-6 (SVC)
Y1-11 (SVC1) - Y1-5 (SVC)
Y1-5 (SVC3) - Y1-6 (SVC)




OK

5.CHECK FOR DTC

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the 4 occupant detection sensors.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1793 is not output.



HINT:

DTCs other than DTC B1793 may be output at this time, but they are not related to this check.



OK

NG

6.REPLACE OCCUPANT CLASSIFICATION ECU
6.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

8.PERFORM SENSITIVITY CHECK
8.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END