Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1794  Open in Occupant Classification ECU Battery Positive Line  


DESCRIPTION

DTC B1794 is set when a malfunction is detected in the occupant classification ECU.

DTC Code DTC Detection Condition Trouble Area
B1794 One of following conditions is met:
·

Occupant classification ECU circuit malfunction

·

Occupant classification ECU malfunction

·

Occupant classification ECU receives short circuit to ground signal in passenger side buckle switch circuit for 2 seconds


·

Harness or connector

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1794 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

E285812E02
0.854,0.833 1.771,1.083 0.917,0.25 10 false from Battery 5.229,0.833 5.5,1.031 0.271,0.198 10 false +B 5.229,1.531 5.552,1.729 0.323,0.198 10 false IG2 5.229,2.135 5.583,2.333 0.354,0.198 10 false GND 3.375,1.01 4.333,1.208 0.958,0.198 10 false ECU-B1 3.51,1.698 4.469,1.896 0.958,0.198 10 false IGN 4.74,3.042 6.708,3.292 1.969,0.25 10 false Occupant Classification ECU 0.74,1.531 1.698,1.781 0.958,0.25 10 false from IG2 Relay 4.958,0.719 5.208,0.917 0.25,0.198 10 false 1 4.958,1.396 5.208,1.594 0.25,0.198 10 false 7 4.958,2.01 5.208,2.208 0.25,0.198 10 false 3 4.74,2.823 4.99,3.021 0.25,0.198 10 false Y2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off, and wait for at least 10 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1794 is not output.


HINT:

DTCs other than DTC B1794 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor, occupant detection sensors and occupant classification ECU.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.

Check that the connectors (on the occupant classification ECU side) are not damaged (see page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE)

NG

REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE)
a.
U152943E02
1.406,1.156 1.146,1.146 true 1.427,1.042 1.208,0.906 true 1.771,1.042 2.229,0.854 true 2.281,0.74 2.708,0.938 0.427,0.198 10 false GND 0.146,0.094 2.49,0.458 2.344,0.365 10 false Front view of wire harness connector: (to Occupant Classification ECU) 0.979,0.781 1.198,0.979 0.219,0.198 10 false +B 0.948,1.063 1.156,1.24 0.208,0.177 10 false IG 0.281,1.031 0.531,1.208 0.25,0.177 10 false Y2

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the Y2 ECU connector.


d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Measure the resistance and voltage according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y2-3 (GND) - Body ground Always Below 1 Ω


Standard voltage:
Tester Connection Switch Condition Specified Condition
Y2-1 (+B) - Body ground Always 11 to 14 V
Y2-7 (IG) - Body ground Ignition switch ON




OK

5.CHECK FOR DTC

NG

REPLACE HARNESS OR CONNECTOR

5.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Connect the connectors to the occupant classification ECU.


d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




g.

Turn the ignition switch off, and wait for at least 10 seconds.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1794 is not output.


HINT:

DTCs other than DTC B1794 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE OCCUPANT CLASSIFICATION ECU
6.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

8.PERFORM SENSITIVITY CHECK
8.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END