Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234207 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.REMOVE SPIRAL CABLE SUB-ASSEMBLY

a.

If there are any defects as mentioned below, replace the spiral cable sub-assembly with a new one:

Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.


b.
C353079E01
0.375,0.958 0.635,1.198 0.26,0.24 1.167,1.49 1.427,1.729 0.26,0.24 1.677,0.906 1.938,1.104 0.26,0.198 2.229,0.927 2.552,1.167 0.323,0.24 1.313,4.26 1.635,4.5 0.323,0.24 2.25,4.344 2.573,4.563 0.323,0.219 1.771,0.917 1.927,1.115 0.156,0.198 10 false A 2.281,0.969 2.74,1.167 0.458,0.198 10 false P14 0.458,1 0.771,1.198 0.313,0.198 10 false I1 1.25,1.531 1.563,1.729 0.313,0.198 10 false I2 1.385,4.292 1.844,4.49 0.458,0.198 10 false J45 2.313,4.365 2.771,4.563 0.458,0.198 10 false J11

Check the spiral cable sub-assembly.

i.

Set the spiral cable sub-assembly to the center position (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown. Then rotate the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the U4 (uecs) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J11-1 - I1-2 Always Below 1 Ω
J11-2 - I1-1
J11-3 - I2-1
J11-4 - I2-2
J45-6 - A-10
J45-5 - A-9
J45-4 - A-8
J45-3 - A-7
J45-2 - A-6
J45-2 - P14-4
J45-1 - P14-3
J45-12 - A-5
J45-11 - A-4
J45-10 - A-3
J45-9 - A-2
J45-8 - A-1
J45-8 - P14-2
J45-7 - P14-1



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the U4 (uecs) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J11-1 - I1-2 Always Below 1 Ω
J11-2 - I1-1
J11-3 - I2-1
J11-4 - I2-2
J45-6 - A-10
J45-5 - A-9
J45-4 - A-8
J45-3 - A-7
J45-2 - A-6
J45-2 - P14-4
J45-1 - P14-3
J45-12 - A-5
J45-11 - A-4
J45-10 - A-3
J45-9 - A-2
J45-8 - A-1
J45-8 - P14-2
J45-7 - P14-1


NOTICE:

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.