Home › Vehicle Interior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM27M0U _58 Vehicle Interior _049134 WIPER / WASHER _0234267 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Fluid Level Warning Switch Circuit  


DESCRIPTION

When the volume of washer fluid decreases below a certain level (when the washer fluid level warning switch is turned ON), the combination meter warns the driver through the washer fluid level warning light illumination*1 or warning message*2 on the combination meter.

HINT:

*1: for LCD Display Type


*2: for TFT Display Type

WIRING DIAGRAM

E146596E07
5.292,3.054 5.546,3.209 0.254,0.156 10 J28 5.292,3.223 6.500,3.384 1.208,0.161 10 Combination Meter 5.543,1.893 5.944,2.049 0.401,0.156 10 WLVL 5.253,1.791 5.445,1.943 0.191,0.152 10 15 2.093,2.278 2.362,2.434 0.269,0.156 10 A27 2.093,2.446 4.305,2.627 2.212,0.182 10 Washer Fluid Level Warning Switch 2.736,1.894 2.853,2.056 0.117,0.162 10 E 3.476,1.894 3.593,2.056 0.117,0.162 10 S 3.672,1.793 3.778,1.951 0.106,0.158 10 1 2.541,1.793 2.647,1.951 0.106,0.158 10 2

PROCEDURE

1.READ VALUE USING TECHSTREAM (WASHER FLUID LEVEL WARNING SWITCH)
a.

Check the Data List for proper functioning of the washer fluid level warning switch.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Washer Switch Washer fluid level warning switch / ON or OFF ON: Washer jar is empty
OFF: Washer jar is full
-

OK:

On screen, each item changes between ON and OFF according to above chart.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
2.CHECK WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
a.
E146598E01
0.095,0.074 2.607,0.419 2.512,0.344 10 Component without harness connected: (Washer Fluid Level Warning Switch) 2.446,1.501 2.583,1.662 0.137,0.161 10 S 0.878,1.501 1.015,1.662 0.137,0.161 10 E 2,1.582 2.408,1.582 false 1.036,1.582 1.444,1.582 false

Disconnect the A27 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A27-1 (S) - A27-2 (E) Washer jar is empty Below 1 Ω
A27-1 (S) - A27-2 (E) Washer jar is full 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (WASHER FLUID LEVEL WARNING SWITCH - COMBINATION METER)

NG

REPLACE WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WASHER FLUID LEVEL WARNING SWITCH - COMBINATION METER)
a.
U152756E02
1.469,1.677 1.094,1.677 false 2.344,1.677 1.969,1.677 false 2.219,3.646 2.219,4.125 false 0.219,2.365 2.469,2.719 2.25,0.354 10 false Front view of wire harness connector: (to Combination Meter) 2.031,4.156 2.427,4.323 0.396,0.167 10 false WLVL 0.167,3.521 0.406,3.667 0.24,0.146 10 false J28 0.219,0.115 2.615,0.51 2.396,0.396 10 false Front view of wire harness connector: (to Washer Fluid Level Warning Switch) 0.396,1.563 0.667,1.708 0.271,0.146 10 false A27 0.958,1.594 1.073,1.74 0.115,0.146 10 false S 2.396,1.594 2.51,1.74 0.115,0.146 10 false E

Disconnect the A27 switch connector.


b.

Disconnect the J28 meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A27-1 (S) - J28-15 (WLVL) Always Below 1 Ω
A27-2 (E) - Body ground Always Below 1 Ω
A27-1 (S) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR