Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Front Power Seat does not Operate with Front Power Seat Switch  


DESCRIPTION

When a signal is input into the position control ECU and switch assembly, the ECU manages the signals received from the power seat switches, and operates each motors. If the position control ECU and switch assembly receives more than 2 motors operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B226313E13
4.896,0.563 5.208,0.719 0.313,0.156 10 false +B1 4.906,1.063 5.302,1.219 0.396,0.156 10 false SYSB 2.604,1.229 3.135,1.385 0.531,0.156 10 false ECU-B1 2.385,0.719 3.365,0.885 0.979,0.167 10 false FR P/SEAT LH 4.917,1.552 5.344,1.708 0.427,0.156 10 false GND1 4.719,1.958 6.354,2.302 1.635,0.344 10 false Position Control ECU and Switch Assembly 4.604,0.583 4.854,0.74 0.25,0.156 10 false Z9 4.552,1.083 4.854,1.24 0.302,0.156 10 false Z10 4.583,1.563 4.792,1.719 0.208,0.156 10 false Z9 4.635,0.365 4.729,0.521 0.094,0.156 10 false 7 4.583,0.885 4.76,1.042 0.177,0.156 10 false 12 4.625,1.375 4.719,1.531 0.094,0.156 10 false 2 0.917,0.563 1.708,0.76 0.792,0.198 10 false from Battery 0.917,1.073 1.698,1.271 0.781,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

Result
Result Proceed to
All power seat functions does not operate A
One or more power seat functions does not operate B



A

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

B

Go to OTHER FLOW CHART (One or more Power Seat Motors do not Operate)

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U152023E02
2.083,1.167 2.281,1.469 2.281,1.469 2.458,1.469 false 1.313,2.281 1.063,1.885 1.063,1.885 0.875,1.885 false 1.375,2.615 1.594,3 1.594,3 1.75,3 false 0.542,0.844 0.833,1.021 0.292,0.177 10 false Z10 0.583,2.333 0.781,2.51 0.198,0.177 10 false Z9 2.531,1.396 2.99,1.552 0.458,0.156 10 false SYSB 0.115,0.125 0.302,0.302 0.188,0.177 10 false *a 1.833,2.927 2.146,3.094 0.313,0.167 10 false +B1 0.438,1.802 0.844,1.958 0.406,0.156 10 false GND1

Disconnect the Z9 and Z10 position control ECU and switch assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z9-7 (+B1) - Body ground Always 11 to 14 V
Z10-12 (SYSB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-2 (GND1) - Body ground Always Below 1 Ω




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR